Olafus LAW10E LED RGB Flood Light User Manual

June 5, 2024
Olafus

Olafur LAW10E LED RGB Flood Light

Olafus LAW10E LED RGB Flood Light
product

SAFETY INFORMATION

Disconnect the power supply before attempting any work on the unit!

  • Installing these units involves work on the mains voltage supply; installation must therefore be carried out professionally in accordance with the appliance national wiring regulations
    and electrical operating conditions.

  • The product must be installed by a licensed professional electrician.

  • Check all components for damage, do not use the product if it is damaged.

  • To ensure the product can work normally, please use it in the voltage within the range on the lamp label.

  • The floodlight enclosure heats up when the light is on.Please adjust the angle of the light after the power off for 10-15 minutes. Do not look into the LED light at a short range or any prolonged period(>5 min).

  • Do not install the unit on (normally) flammable surfaces.

  • Do not alter or change parts of the light at will, in case of the accidents such as breakage, fall, electric shock, fire, etc.

  • To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach

  • The light is IP66 waterproof, but the plug is non-waterproof. Please connect the plug indoor or connect to a socket that provides IP65 protection.

  • Please use tools to adjust the lights.

  • The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.

  • Never plug the light in with wet hands in case of electric shock.

  • This light is a non-dimmable product. To avoid failure, please don’t connect it with the dimming controller.

  • Do not connect this light fixture to an ungrounded electrical system.

  • WARNING: Installing this light in an ungrounded electrical system may cause the metal parts of the light to carry current if any wires or wire connections are damaged or loose. In this case, anyone who touches the light will receive an electric shock, resulting in injury or death.

  • Be sure to use wire nuts/connectors rated for the correct gauge and number of wires used. NOTE: Make sure there are no exposed wire bundles outside the wire nut/connector (if applicable).

  • Be careful not to damage or cut the wire insulation (covering) during installation. Do not let the wires touch any sharp edges.

  • The floodlight is supplied with cable and must be terminated using a terminal block (not supplied) in a suitable IP rated enclosure (not included).
    For type Z attachments:

  • The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.

  • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

PAIRING LED LIGHT WITH”SMART LIFE” App.

NOTE Turn ON/OFF the Smart LED Light three times until the LED Light starts to flash quickly, whichin dicates the success of the factory reset.

Step 1: “Smart Life” App Installation.
There are 2 options for obtaining and installing the “Smart Life” App on your smart device.

  1. Scan the QR code on the right.
  2. Search for “Smart Life” in the App Store or Google Play.Olafus LAW10E LED RGB Flood Light fig 1

Step 2: Enter the “Smart Life” App. and register an account and log in. If you already have an account for Smart Life App., Please select “Log in with existing account”.
Note: You will need your “Smart Life” App. username and password to pair with Amazon Alexa and/or Google Assistant.Olafus LAW10E LED RGB Flood Light
fig 2

Step 4. How to pair the LED Light.Olafus LAW10E LED RGB Flood Light fig
3

Step 5. Name the LED light and tap “Done”. You will find the device you’ve named is shownon the App homepage. Tap the device to enter the setting page. You can now control the light with Smart Life App. on this setting page.Olafus LAW10E LED RGB Flood Light fig 4

AMAZON ALEXA

Please make sure that your Alexa App. is connected to Amaozn Echo, and both work together successfully under your Wi-Fi network.

Step B : Type “Smart Life” to search for “Smart Life”, and enable “Smart Life” on Alexa.

Step C : Enter your account and password of Smart Life App., tap “Link Now”, then tap ” Authorize” on the next page authorize Smart Life Info to Alexa. Note: Same account and password as Smart Life App.

Step D : Once your Smart Life account is successfully connected to Alexa, the following page will pop up. Tap “Done” on top leftcorner, then tap “DISCOVER DEVICES” on the next page.Olafus LAW10E LED RGB Flood Light fig
9

  1. Power on the LED Light.

  2. Power off it three times quickly until the LED chips flashes, it indicates that the flood

  3. Tap the confirmation button to pair the LED Light.

  4. Enter Wi-Fi password to join your network. Please
    Note:
    This smart LED Light can only support 2.4 GHz network and cannot work with 5.0 GHz network.
    b. Please check if your home network is 2.4 GHz and make sure that your phone has been connected to your Wi-Fi network. Please ensure your network is not hidden.

  5. Wait till it is successfully connected.
    Note: If the LED Light is still flashing until the progress map reaches 100%, the pairing fails, and you will need to repeat the previous 4 steps to pair the LED Light.
    Schritt 4. wie man den Strahler repairieren.

Step E : You will find that Google Home has found the device named “Smart LED Light” on this page.

COMPONENTS AND STRUCTURE

1. Tempered Glass Lid 2.LED Light Source 3. Lamp Bracket 4. Antenna

NOTE

  1. Make sure that the distance between the light and the object being lit is more than 1 meter, so as to avoid high temperature caused by short distance.
  2. Safety Class II=This lamp is doubly insulated and may not be wired to a protective conductor.
  3. Lights that are not suitable for covering with thermal insulation materials.

Limitations of Indoor and Outdoor Use

  1. This light is waterproof and dustproof. It is protected against the rain, but it cannot be immersed in water.
  2. The mounting position of this light should be able to bear at least 10 times as heavy as the light.
  3. This light is powered by High Voltage Alternating Current (HVAC). It should be connected to the ground wire and kept away from easy reach.
  4. This light should be used in condition with sound heat dissipation. The working temperature of it should be less than 40°C. Overhigh working temperature will cause serious lumen depression and affect lifespan of the light.

INSTALLATION STEPS

Step 1: According to the spacing (see the “A” part of the picture) of two screw bits on the LED Light bracket, drill two mounting holes.
Step 2: Put the bracket onto the prepared mounting holes and then screw it on.
Step 3: Adjust the beam direction as you like, and then plug into the main socket.
NOTE: Recommended installation height not higher than 5 m (16.4 ft)

OPERATION & MAINTENANCE

  • Prior to cleaning the light, make sure it has been disconnected from the power supply.
  • The unit is not suitable for burglar alarm systems as it is not tamperproof in the manner prescribed for such systems.
  • Never use any chemicals or corrosive substances for cleaning.

DISPOSAL

Electrical and electronic equipment, accessories and packaging must be recycled in an environmentally compatible manner.
Do not dispose of electrical and electronic equipment as domestic waste.

EU cOuntries only:
Under the current European Directive on Waste Electrical and Electronic equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals