Olafus E10BL LED Bluetooth Floodlight Instruction Manual

LED Bluetooth Floodlight
Instruction Manual

MODEL
E10BL/E3BL /E5BL

PARAMETER

| A – 153x40x90 mm
B – 206×42.5×127 mm
C – 263.5x38x161 mm
6.02×1.6×3.54 in
8.11×1.67×4.92 in
10.35×1.5×6.34 in
---|---
| 100-1 120V AC 60Hz 220-240V AC 501-Hz
| RG 8+2700K
| 1P66
| -25°C – 40°C

APP INSTALLATION

1. Please scan the QRcode
2. Search for ‘HAPPY LIGH1 INC In the Apple Store or Google Play.
3. Download and install the App. as shown in the fracture.

http://download.appglobalmarket.com/happylightingdownload.html

Note:

• Before using the app, please make sure that the Bluetooth of your mobile phone is enabled.
• Unable to connect to Bluetooth: Atter you open the app and select the color. the color doesn’t change on the floodlight, It means that the Bluetooth tats to connect. The card mgnt has been connected to the other phone.

1. You need to disconnect the Bluetooth of the other phone, and then your phone xN be automatically connected to the light. Al this limo, when you turn on (he Bkatooth, It will show that the device Tdones-XXXX is connected, which means that the Bluetooth is connected now
2. 0pon the APP and place the phone near the light, it wit be connected to the neatest Bluetooth without blocking. after the light is turned off and turned on again.

APP INSTRUCTIONS

Color Selection Interface
You could actuate the color ono brightness. Div your favorite color.

Wile Mode Interface
You could control the brightness and dynamic changes of the light by playing local music on the phone.
Dynamic Mode interlace:
The dynamic model of the light (Jump, fade, tash, strobe; and the combination o’ seven typical colors changes, you can adjust the brightness when changing.
Tining Interface:
You can turn on or turn off the light regularly.

App

With the memory function, the light can start at your last choice of color and mode.

1. Brightness Adjustment: Press the – ‘ or to either increase or decrease the brightness. There are 8 levels of adjustable brightness.
2. Stop: Pause color changes in the jump mode, lade mode, flash mode, or automate mode,
3. On/Off rum on or off the light by pressing * •
4. Color Options : Press the colored buttons to select the corresponding knight
5. DIY Mode : After pressing the button DIY1 1 DIY2 DIY3, you can DIY different colors by adjusting the ROB brightness If these keys and these colors are automatically saved, there are 7 variations of a cobra, and more than 4.800 colors are available for you to choose, 3 kinds of the DIY colon can be saved as DIY1 l 01Y21 DIY3,
6. Speed Adjustment : Adjust the speed of color changes in Jump Mode, Fade Mode, and Flash Mode; press the button QUICK to speed up and SLOW to slow down. And 30 kinds of different speeds are available for you to choose.
7. Timing: There are 3 regular intervals 31461-412H to set the timer and the light will be off automatically when the lime is up,
8. Auto Mode : Freely switch Jump Mode, Fade Mode. or Flash Mode.
9. Flash Mode : Make the light flash,
10. Fade Mode: FADE3 is the mode of three-color gradients, and FADE7 is the mode of seven color gradients,
11. Jump Mode: JUMPS Is the mode of three color Jumps, and JUMP7 Is the mode of seven color lumps.
12. Remove the insulation sheet before using the remote control.

COMPONENTS AND STRUCTURE

1. Tempered Glass L4
2. LED LignI Source
3. Lamp Bracket

Note: Cord – type Y attachment For type Y attachment
If the external flext4 cable or cord of teas lure nacre’s damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avo4d a hazard,

NOTE

1.  – Wake sure that the distance between the light and the object being lit is more than 1 meter, so as to avoid high temperature caused by a short distance.
2. – Safety Class II-This lamp is doubly insulated and may not be Wred to a protective conductor.
3. – Caution, risk of electric shock.

Non-User Replaceable Light Source
The light source contained in this flood light shall only be replaced by the manufacturer or his service agent or a similarly qualified person.

Limitation of Indoor and Outdoor Use

1. This light is waterproof and dustproof. It is protected against rain, but it cannot be immersed in water.
2. The mounting position of this light should be able to boar at toast 10 times as heavy as the light.
3. This light should be used in conditions with sound heat dissipation. The working temperature of it should be less than 45°C. Overhigh working temperature will cause serious lumen depression and affect the Meson of the light.

INSTALLATION STEPS

Step 1 : According to the spacing (see the ‘A’ part of the picture) of two screw bits on the LED Light bracket. oil two mount ng hoes.
Step 2 Put the bracKet onto the prepared mounting holes and then screw it on.
Step 3 : Ar*1st the beam direction as you like. and then plug into the main socket.

DISPOSAL

EIOCtrtal and electronic equipment. accessories and packaging must be recycled in an environmentally compatible manner. Do not dispose of electrical and electronic equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste Electrical and Electronic equipment and Its Implementation In national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receivingantenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Manufacturer:
Shen Zhen Shi Zhi Hui Duo Ke Ji You Xian Gong Si
Address: Qian wan Yi to 1 hao A dong 201 shi, qian hai shen gang
he Zuo Qu, shen then, Guang dong, 518000, CN support@olafuslife.com www.olafuslife.com
EU Representative:
Bright star consulting e.K.
Humboldtstr.5, 31812 Bad Pyrmont Germany
support@olafushfe.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>