Olafus 3-LBW55M PIR LED Wall Lights with Motion Sensor User Manual

Olafus 3-LBW55M PIR LED Wall Lights with Motion Sensor

Product Specifications

• Model: 3-LBW55M
• Input Voltage: 100-120V
• Input Current: 0.7A
• Rated Power: 55W
• Luminous Flux: 5500lm
• CCT (Color Temperature): 2700-6500K
• CRI (Color Rendering Index) : 80
• Power Factor: Not specified
• L70B50 Lifetime : Not specified
• Beam Angle : Not specified
• Luminaire Location: Not specified
• Dimensions: 274x196x144mm / 10.79×7.72×5.67in
• Weight: 0.9kg/1.98 lb

Components and Structure

1. Cover
2. LED Light Source
3. Lamp Base
4. Sensor Head

PARTS LIST

SPECIFICATIONS

LED WALL LAMP

Model| 3-LBW55M
Input Voltage| 100-120V 60Hz
Input Current| 0.7A
Rated Power| 55W
Luminous Flux| 5500lm
CCT| 2700-6500K
CRI| ≥80
Power Factor| ≥0.9
L70B50 lifetime| 30000hours L70B50 @25°
Beam Angle| 120°
t a| -20-40°C/-4°F-104°F
Luminaire Location| SUITABLE FOR WET LOCATIONS
DIMENSIONS
Model| 3-LBW55M
Dimensions（LxHxW）| 274x196x144mm /

10.79×7.72×5.67in

Weight| 0.9kg/1.98 lb
Note: The testing standard of the product’s luminous flux: Place the three/two lights on the same horizontal surface for testing, and the tested luminous flux is the accurate luminous flux.|

PAIRING LED LIGHT WITH “Smart Life” APP

• Step 1: “Smart Life” App Download. There are 2 options for obtaining and downloading the “Smart Life” App on your smart device.
  • Scan the QR code on the right.
  • Search for “Smart Life” in the App Store or Google Play.

• Step 2: Enter the “Smart Life” App. Register an account and log in. If you already have an account for Smart Life App, Please select “Log in with existing account”.
  Note: You will need your “Smart Life” App username and password to pair with Amazon Alexa and/or Google Assistant.

• Step 3: Please turn on the Wi-Fi and Bluetooth before connecting LED lights to the “Smart Life” App.

• Step 4: How to pair the LED Light

Set the light to the pending pairing state

1. Power on the LED Light.
2. Turn the light on and off 3 times until it starts flashing, indicating that the light is ready for pairing.

Method 1

1. Tap the “+” button on the top right corner and tap “Add Device” to add a device.

2. The app will automatically search for the device. After discovering the device, tap “Add”.

3. 3. Enter your Wi-Fi password to join your network.
   Please Note:

   • a. This smart LED Light can only support 2.4 GHz network and cannot work with a 5.0 GHz network.
   • b. Please check if your home network is 2.4
     GHz and make sure that your phone has been connected to your Wi-Fi network.
     Please ensure your network is not hidden.

4. Wait for the device to register (about 30-60)

5. Tap “Next” to complete the light pairing.

6. You can tap to change the device name.

7. Tap “Done” to enter the control panel.

Method 2

1. Tap the “+” button on the top right corner and tap “Add Device” to add device

2. Tap “Lighting” and then “Light Source” to enter the next page.

3. Tap the “Next” button to pair the LED Light

4. Enter your Wi-Fi password to join your network.
   Please Note:

   • a. This smart LED Light can only support a 2.4 GHz network and cannot work with 5.0 GHz network.
   • b. Please check if your home network is 2.4 GHz and make sure that your phone has been connected to your Wi-Fi network.
     Please ensure your network is not hidden.

5. Wait for the device to register (about 30-60).

6. Tap “Next” to complete the light pairing.

7. You can tap to change the device name.

8. Tap “Done” to enter the control panel.

HOW TO OPERATE THE APP

1. Color Temperature and Brightness Adjustment

2. Motion Sensing Settings

   • Sensing distance setting
     Low (13-26ft), Middle (26-49ft) and High (49-72ft).

   • Full light duration setting
     From 5s to 60mins.

3. Dusk-to-Dawn SettingsThe sensitivity can be set to Day, Dusk, Evening, Night, and Dark, and the light will be on at the selected time.

4. Slight Bright Mod
   Here you can choose the slightly bright mode and its brightness

   • Microlight duration setting Microlight duration can be set from 1min to 8hrs, or it can be set to be always on.
     Note: The countdown and timer mode will not work when exiting the app.

HOW TO CONNECT WITH ALEXA AND GOOGLE ASSISTANT APP

Tap “Me”, find the third-party voice device you want to connect to and tap it, then follow the steps to connect

OPERATION INSTRUCTIONS

Detection Range: 180

NOTE:

1. The PIR sensor shall always be tilted slightly downward.
2. The orientation angle of the sensor shall be between 5-45°

RECOMMENDED INSTALLATION HEIGHT: 6.5-13.1 feet above the ground

• When mounted 8ft above the ground and the sensor is 5° down, the maximum sensing distance is about 72ft.
• When mounted 8ft above the ground and the sensor is 45° down, the minimum sensing distance is about 19ft.

Note: The detection distance of the sensor is the farthest when the ambient temperature is 25℃. Any temperature fluctuations above or below 25℃ will affect the detection distance. If the light continues to detect motion while it is on, it will remain on until the motion stops.

The motion sensor is more sensitive to horizontal movement than vertical movement.

PREPARATION

NOTE: Before beginning assembly of the product, make sure all parts are present. Compare parts with the parts list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 30-60 minutes.

• Recommended to be installed 2.5m (8.2ft) above the ground but not higher than 5m (16.4ft).
• Product appearance may vary from the image shown.

TOOLS REQUIRED

（not included）

WARNING: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED

CAUTION:

• PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT MAIN CIRCUIT BREAKER BOTH ARE OFF.
• IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN

RISK OF SHOCK:
BEFORE BEGINNING INSTALLATION, TURN OFF ELECTRICITY
AT THE CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX

NOTE: BE SURE TO USE WIRE NUTS/CONNECTORS RATED FOR THE CORRECT GAUGE AND NUMBER OF WIRES USED. MAKE SURE THERE ARE NO EXPOSED WIRE BUNDLES OUTSIDE THE WIRE NUT/CONNECTOR (IF APPLICABLE).
BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE INSULATION (COVERING) DURING INSTALLATION. DO NOT LET THE WIRES TOUCH ANY SHARP EDGES.

WARNING:

DO NOT CONNECT THIS LIGHT FIXTURE TO AN UNGROUNDED ELECTRICAL SYSTEM. ATTACH THE GROUND FIXTURE WIRE TO EITHER THE GREEN GROUND SCREW ON MOUNTING PLATE OR THE GROUND WIRE IN THE OUTLET BOX.

INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM MAY CAUSE THE METAL PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE CONNECTIONS ARE DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE AN ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH.

INSTALLATION STEPS

FOR WET LOCATION, MAKE SURE TO FILL THE GAP OF THE EVA GASKET AND MOUNTING SURFACE WITH SEALING COMPOUND OR SILICONE GLUE.

Note: The raised part (RA) of the metal plate must be engaged with the recessed part (RE) of the base, otherwise it cannot be installed

TROUBLESHOOTING

LED senses a movement, the light does not light up

|

1. The light is not energized

2. Other surrounding light sources make the light misjudge it as daytime

3. During the day, the brightness is in night mode

4. Internal wiring is loose

|

1. Check power-on status

2. Turn off the nearby lights or sensor head to other directions

3. Reset

4. Rewiring after power failure

LED sensor light did not go out, continued to light up| Continuous movement within the sensing range| Check the relevant area and retune or override the sensor head if necessary

LED sensor light illuminates during the day

|

The shadows around the sensor make it mistakenly think it’s night

|

1. Do not cover the sensor head

2. Place the light in a place where the light is bright enough during the day

LED sensor light flashing| Surrounded by other unstable light sources shining onto the induction| Avoid being exposed to such light sources

LED lights turn on unexpectedly

| 1. Wind blows the branches

and bushes within the sensing range

2. Sensing cars on the road

3. Sudden temperature change due to climate factors or fans, exhaust from open windows

|

1. Adjust its scope

2. Adjust its scope

3. Change irradiation area

FCC STATEMENT

FCC Warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body

HK JW Illumination Co., Limited
Unit 616, 6/F., Kam Teem Industrial Building,
135 Connaught Road West, Sai Wan Hong Kong

Manufacturer/Hersteller: MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos Nicosia,
Cyprus

UK Importer: MDH LIGHTING LTD
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom

Made in China
support@olafuslife.com www.olafuslife.com

References

• OLAFUS LED Light - Keep Brighter and Safe for Your Life

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>