SHARP UA-KIN52E UA-KIN42E Air Purifier Instruction Manual

SHARP UA-KIN52E UA-KIN42E Air Purifier

Product Specifications

• Model: UA-KIN52E, UA-KIN42E
• Type: Smart Air Purifier with Humidifying Function
• Languages: English, German, Spanish, French, Italian, Dutch, Polish

Product Usage Instructions

Before using the product, please read and save these instructions. Follow the safety precautions to reduce the risk of fire, electric shock, and injury:

1. Read all instructions before using the product.
2. Use the product only for intended household use as described in the manual.
3. Supervise children using the appliance.
4. Do not operate if the power cord or plug is damaged.
5. Follow specific instructions for the power cord and plug.
6. Avoid using near gas appliances or flammable materials.
7. Avoid exposing the product to water or damp locations.
8. Avoid inserting fingers or foreign objects into air inlets or outlets.
9. Avoid drinking water from the Water Tank or Humidifying Tray.

General Usage Instructions

Follow these general guidelines for optimal use of your Sharp Air Purifier:

1. Place the air purifier in a well-ventilated area for efficient operation.
2. Ensure the product is connected to a suitable AC 220-240 volt outlet.
3. Regularly clean and maintain the air purifier as per the user manual instructions.
4. Do not block the air inlets or outlets for proper airflow.
5. Monitor the filter indicator and replace filters as recommended by the manufacturer.

Frequently Asked Questions

Q: Can the air purifier remove harmful gases like carbon monoxide?
A: The air purifier is not designed to remove harmful gases such as carbon monoxide.

Q: Can children use this air purifier?
A: Children aged 8 years and above can use the appliance under supervision.

Please Read Before Operating Your Air Purifier
The air purifier draws in room air through the air inlet, circulates it through a Pre-Filter, a Deodorizing Filter and a HEPA Filter inside the product, and then discharges it through the air outlet. The HEPA Filter can remove 99.97% of dust particles as small as 0.3 microns that pass through the filter and also helps absorb odours. The Deodorizing Filter gradually absorbs odours as they pass through the filter. Some odours absorbed by the filters will break down over time, causing additional odours. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odours may become noticeable sooner than expected. If these odours persist, replace the filters. When minerals in tap water adhere to the filters and become hard and white, they absorb odours in the room that can cause the emission of an unpleasant odour when the Humidifying Filter is dry. (Varies depending on water quality and other environmental factors) If this occurs, perform the Humidifying Filter maintenance. (Page 20)
NOTE · The air purifier is designed to remove air-suspended dust and the odours.
The air purifier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke. The air purifier may not completely remove an odour if the source of the odour is still present.

PART NAMES

MAIN BODY

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS before using this product.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

WARNING
1. Read all instructions before using the product.
2. Use the product only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
3. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
4. Never operate the product if the power cord or plug is damaged or the product is malfunctioning or damaged.
5. If the power cord or plug is damaged, it must be replaced by the manufacturer, its service agent, a Sharp authorized Service Centre or similarly qualified persons in order to avoid a hazard. Contact the nearest Service Centre for any problems, adjustments, or repairs.
6. Do not repair or disassemble the product yourself.
7. Follow the instructions below for the power cord or plug. It may cause short circuit, excessive heat, electric shock or fire. a. Use only AC 220-240 volt outlet. b. Do not use the product if the power cord or plug is damaged or the connection to the wall outlet is loose or damaged. c. Always turn off the product before unplugging the power plug.

d. Always unplug the product in the following cases. · Before moving the product. · When replacing the filter. (Even when opening the Back Panel) · When refilling water. · Before maintenance of the product. · When the product is not in use.
e. Be sure to pull the power plug and not the power cord.
f. Do not touch the power plug with wet hands when inserting or unplugging from the wall outlet.
g. Periodically remove dust from the power plug.
h. Always observe the following as to not damage the power cord. · Do not damage cord with Caster Wheels when moving the product. · Do not run cord under carpeting. Do not cover the power cord with throw rugs, runners, or similar coverings. · Do not put heavy things on the power cord or pinch it. · Do not run the power cord under furniture or other appliances. · Run the power cord away from traffic area and where it will not be tripped over.
8. Do not use this product near gas appliances, fire places, candle fire, incense or sparks from lit cigarettes. When the product is operated with gas appliances in the same room, Ventilate a room periodically, otherwise it may cause carbon monoxide poisoning.
9. Do not operate the product in a room with flammable gas, such as oily residue or chemical fumes.
10. Do not expose the product to rain, or use near water, in a bathroom, laundry area or other damp location.
11. Do not insert fingers or foreign objects into the air inlets or air outlets.
12. Do not look into the air outlets.
13. Do not drink the water in the Water Tank or Humidifying Tray.
14. Replace the water in the Water Tank daily with fresh tap water, and regularly clean the Water Tank and Humidifying Tray. When the product is not in use, dispose of the water in the Water Tank and Humidifying Tray. Leaving water in the Water Tank or Humidifying Tray can cause mold, bacteria, and bad odours. In rare cases, such bacteria can be a health hazard.

NOTE
– Radio or TV Interference –
If the product should cause interference to radio or television reception, try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the product and radio/TV receiver.
3. Connect the product into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

CAUTIONS CONCERNING INSTALLATION
1. Place the product on a level and stable surface with sufficient air circulation. Strong wind or Dust through the window may prevent the product’s air purifying performance and efficacy. When placed on heavy carpet, the product may vibrate slightly. Place the product on a level surface to avoid water leakage from the Water Tank and Humidifying Tray.
2. Avoid a location where the sensors are exposed to direct breeze or draft if the product has sensors. The product may not operate properly.
3. Avoid use in locations where furniture, fabrics, or other items may come in contact with and restrict the air inlets and/or outlets.
4. Avoid locations exposed to direct sunlight. It may cause to change shape or colour of the product.
5. Avoid locations where the product is exposed to condensation or drastic changes in temperature. Use under appropriate conditions between 0 ºC ­ 35 ºC.

6. Avoid use in locations where greasy or oily smoke is generated. (such as in a kitchen, etc.). The Main Body surface may crack and the sensors may malfunction as a result.
7. The dust collecting ability of the product is effective even when the product is up to 3 cm from the wall, but the surrounding walls or floor may get dirty. Please place the product at a distance from the wall. The wall directly behind the air outlets and the floor or rug on which the product placed may become dirty over time. When using the product for an extended period of time at the same location, periodically clean the walls, the floor or the rug.
8. Do not place the product near or on hot objects, such as stoves or heaters, or where it may come into contact with steam.

CAUTIONS CONCERNING FILTER
1. Follow the instructions in this manual for filter installation and maintenance. (Page 9, 22)
2. Take out the filters from the plastic bag before placing the filter in the Main Body.
3. Do not operate the product without the filters properly installed.
4. Do not wash and reuse the HEPA Filter and the Deodorizing Filter. Washing will not improve filter performance and can also cause electric shock or operating malfunctions.
5. Do not operate the product in a rooms where aerosol insecticides are present. It may cause the odour of insecticide may be remained in the product and emitted from the air outlets.

CAUTIONS CONCERNING OPERATION
1. Do not block the air inlets or air outlets.
2. Always operate the product in an upright position.
3. When carrying the product, first remove the Water Tank and Humidifying Tray not to spill water, and then hold the

product by the handles on both sides.
4. Always lift up the product when moving it on easily damaged flooring, an uneven surface, or carpet.
5. Do not change the direction of the product while moving using the Caster Wheels.
6. When moving the product by its Caster Wheels, move it slowly and in a horizontal direction.
7. Do not operate the product without the Water Tank or Humidifying Tray properly installed.
8. Be careful not to catch your fingers when removing or installing the Water Tank.
9. When refilling the Water Tank, make sure no water leaks from the Water Tank.
10. Be sure to wipe off any excess water on the outside of the Water Tank.
11. Do not use hot water (40 ºC or more), chemical agents, aromatic substances, dirty water, or other damaging substances. Doing so can deform the product or cause it to malfunction.
12. Use only fresh tap water. Using other water sources risks the growth of molds, fungi, or bacteria.
13. Do not shake the Water Tank while holding the Tank Handle.

CAUTIONS CONCERNING MAINTENANCE
1. Follow the instructions in this manual for maintenance. (Page 18 – 23)
2. Clean the exterior with a soft cloth only.
3. Do not use detergents other than what is mentioned in this manual (Page 19 , 21). Do not use volatile fluids and/or detergents. The Main Body surface may be damaged or cracked with strong corrosive cleansers, benzine, paint thinner, polishing powder or grease. The Humidifying Tray may cause deformation, tarnishing, cracking (water leakage). In addition, the sensors may malfunction as a result if the product has sensors.
4. Do not scrub the Back Panel (Pre-Filter)

hard during its maintenance.
5. The frequency of descaling maintenance will depend on the hardness of and the impurities in the water that you use; the harder the water the more often descaling will be necessary.
6. Do not remove the the Humidifier Float and the Roller. If the the Humidifier Float and the Roller comes off, refer to page 21.
7. When replacing filters or any accessories, use specified parts in this manual.

WARNING
When remotely controlling the air purifier
In case of remote operation from outside, you may not be able to check air purifier current condition or the area around it and the situation concerning anyone possibly staying there, so please adequately confirm safety before use.
1. Make sure the electric plug is fully inserted into a power socket, and there is no dust on the plug or in the socket hole. (It may cause heat, combustion, fire, etc., due to poor contact or contact failure)
2. Make sure beforehand to check the ambient environment of the product, because the air flow from the product may cause unexpected phenomenon (such as fall down unstable item), and resulting in fires, wounds, defacement of house belongings.

CAUTION FOR USE
1. Agreement with “Terms of Service” is required to use App.
2. Ensure that the App is up to date. 3. Screens and illustrations in this book
are for explanation, there are some differences to the actual product. 4. In the case of bad connection, the App may not be able to control the air purifier. The current operation of the air purifier may not be accurately reflected on the App. 5. Locking smart device display is recommended to avoid incorrect operation. 6. Communication charges will occur by the download and use of the App.

same frequency (2.4GHz) as this product. *The Bluetooth® word mark is registered
trademarks owned by Bluetooth SIG,. Inc.
b. Near the product which emit magnetic field. (e.g. microwave oven)
c. Near the place with static electricity. d. Near the place where the radio
disturbance occurs. e. Near the other wireless
communications device.
2. Wireless connection and performance cannot be guaranteed for all routers or environmental conditions. At the following places, Wi-Fi connection might be unstable: a. Inside of the building made with concrete, reinforcing steel or metal. b. Near the obstruction. c. Near the wireless communications device using the same frequency.
3. Wi-Fi of this product corresponds to channel 1 – 13. It’s not available to communicate with the routers set up to other channels.
Caution for personal information (related to Security)
1. Using Wi-Fi device has the possibility of interception regardless of secret code setting.
2. Make sure to use the network under your management.
3. Initialize the device when sold, disposed or handover from/to a third person. See page 16 on how to initialize.

CAUTION FOR Wi-Fi
Caution for usage about electrical wave
1. Usage of the application is not guaranteed under below environment: a. Near Bluetooth® wireless communications device using the

FEATURES

Unique Combination of Air Treatment Technologies
Plasmacluster
Plasmacluster treats the air similar to the way nature cleans the environment by emitting a balance of positive and negative ions.

“Plasmacluster” and “Device of a cluster of grapes” are trademarks of Sharp Corporation.

• The number in this technology mark indicates an approximate number of ions supplied into air of 1 cm3, which is measured around the centre of a room applicable floor area (at 1.2 m height above the floor) when the product is placed close to a wall at the MED mode setting.

Triple Filteration System + Humidification
Pre-Filter
Pre-filter traps dust larger than approx. 240 micron particles.
Deodorizing Filter
Deodorizing filter absorbs many common household odours.
HEPA Filter
HEPA filter traps 99.97% of particles as small as 0.3 microns.
Humidifying Function
Comfortable Humidity Indoors Keeps Your Skin and Throat Moisturized and Healthy.
Unique Airflow
Powerful air suction and unique airflow quickly and efficiently collect dust and other particles. Faster airflow at a 20º angle collects dust at lower levels in the room for more effective cleaning. Plasmacluster can remove static electricity and can thus prevent dust from attaching to walls and other surfaces.

HEPA Filter Deodorizing Filter
Pre-Filter
· The illustration in this instruction manual is UA-KIN42E.

Wi-Fi Function
· Confirm that condition of air quality of the room and the air has become clean visually. · Control the product through smart devices as remote control. · Propose optimal timing for filter exchange.

Product information and accessories
Scan the QR code for more information about the Sharp Air Purifiers.

UA-KIN52E

1 Operation Panel / Display 2 Air Outlet (Front) 3 Main Body 4 Caster Wheels (4 Locations) 5 Caster Stopper (Right & Left)
Unit Holder 6 (Plasmacluster Ion Generating
Unit) 7 Unit Cleaning Brush 8 Unit* Cover 9 Tank Handle 10 Water Tank 11 Tank Cap 12 Humidifying Filter 13 Humidifying Tray 14 Tray Panel 15 Humidifier Float 16 Roller 17 Air Outlet (Back) 18 Handle (2 Locations)
Sensor Filter / 19 Sensor (Internal)
Sensitive Dust 20 Power Cord, Power Plug 21 HEPA Filter 22 Deodorizing Filter 23 Back Panel 24 Air Inlet

• The Unit refers to Plasmacluster Ion Generating Unit. (The same as below.)

24

20

21 22

EN-8

BEFORE FIRST USE
· To maintain the quality of the filter, it is installed in the product and packaged in a plastic bag.
· Be sure to stop operation and unplug the product before filter installation or replacement.

FILTER INSTALLATION

1. Remove the
Back Panel.

Back Panel

REFILLING THE WATER TANK
1. Remove the Water Tank.

ENGLISH

2. Take out the filters from the plastic
bag.

HEPA Filter Deodorizing Filter

(Only UA-KIN52E)

3. Install the filters in the correct order
as shown.
HEPA Filter

Tag Deodorizing Filter

4. Install the Back

Click

Panel.

Click

Tank Handle Water Tank
2. Fill the Water Tank with the tap water.
Tank Cap
‘6–
3. To prevent leaks,
securely tighten the Tank Cap.
4. Install the Water
Tank.
Click

NOTE · When replacing the filters, making a memo of
the start of use date is recommended. · Do not operate the product without the filters.
EN-9

OPERATION
Wi-Fi SETTINGS
BEFORE YOU BEGIN
· By connecting your air purifier with your smart device, you can use the air purifier more conveniently.
Ensure your smart device is connected to a 2.4 GHz Wi-Fi Network. Wi-Fi Protected Setup (WPS) Access Point (Router)
· The recommended encryption method is WPA2 (AES).
Ensure your smart device meets minimum software requirements (as of January 2024) :
· Smartphones / tablets of Android 8 or later · iPhones, iPod touch, iPads of iOS 12 or later Product Wi-Fi specifications · Wireless LAN: IEEE802.11b/g/n · Frequency range: 2.4GHz frequency band
Trademarks · “Wi-Fi®” is a registered trademark of Wi-Fi Alliance®. · “Android” is the trademark of Google Inc. · “iPhone”, “iPod touch”, “iPad” are the registered trademarks or trademarks of Apple Inc. · The other company names, corporate names, product names mentioned in the handling instructions are trademarks and registered trademarks of each company.
INITIAL SET UP
NOTE · When pairing the smart device to the air
purifier, please ensure they are both connected to the same Wi-Fi network.
1 DOWNLOAD & SIGN UP
1. Install the designated App “Sharp Life Air” to your smart device.
· Available to download from the Apple Store or Google Play.
· Scan the QR code on page 5 for product information.

2. Connect your smart device to the router and launch the App. Follow instructions on the App.
i. Review the “Privacy and Data Utilization Policy” and “Terms of Use”.
ii. Enter Your Date of Birth. iii. Sign in using your Sharp account
(SHARP ID).
· If you do not have a SHARP ID, please register to create a SHARP ID.
iv. Enter a name for your smart device.
2 CONNECTION OF THE AIR PURIFIER AND A ROUTER
NOTE · If you have stealth settings or MAC filtering
settings on the router, please cancel them. · The product network ID is displayed as
“AP-SHARP-XX” (where XX is a 2-digit number below the product MAC address).
1. Tap ” ” at the upper left part of the “Home” screen, and select “Pairing” “Connection with a router”.

EN-10

ENGLISH

2. Follow instructions on the App.
· If the Wi-Fi Lamp lights up after the notification sound, the connection is successfully completed.

Light up

Tap “NEXT”.

3 CONNECTION BETWEEN THE AIR PURIFIER AND A SMART DEVICE
1. Tap “Pair” for the air purifier you would like to pair.

(MODEL NAME)
· If you do not see the screen above, tap ” ” at the “Home” screen, and select “Pairing” “Already connected with a router”.

2. Follow instructions in the App.
· If the Wi-Fi Lamp lights up after the notification sound, the connection is successfully completed.

Light up

How to set Wi-Fi ON / OFF after completing the INITIAL SET UP
If you would like to turn the Wi-Fi OFF:

Press for 3 sec.
NOTE · Turning the Wi-Fi off will result in not being able
to control the air purifier with the designated App.
If you would like to turn the Wi-Fi ON again:
(How to restore the Wi-Fi connection to the original network.)

Press for 3 sec. The Wi-Fi Lamp will flash after you press the WiFi Button. And within about 3 minutes, you will hear four short beeps. Some time after this beep sounds, the Wi-Fi Lamp lights up and the Wi-Fi connection will be restored to the original network. The designated App can now be used again to control the Air Purifier.
NOTE · Wi-Fi ON / OFF can also be set from ” : Wi-
Fi adapter ON/OFF”. (Page 14, 16) In this case, Wi-Fi connection with the router will be automatically restored. · Reconnection to the Wireless Router may take a few minutes to complete, after turning Wi-Fi on again.

The INITIAL SET UP is completed.
EN-11

START/STOP
START

STOP

NOTE
· When the product starts operation, the operation starts in the previous mode it was operated in.

SHARP LIFE AIR MODE

When the product is connected to Sharp Cloud
Sharp Cloud will analyze and set the optimal operation for your room based on the information retrieved from sensors on the product and your usage records.
When the product is not connected to Sharp Cloud
The fan speed and the humidification ON / OFF are automatically controlled depending on the six detection. (PM2.5 / Usual dust / Odour / Temperature / Humidity / Light)
NOTE · If press the Humidify ON/OFF Button, the
operation mode will change to (AUTO).

SELECT AIR VOLUME AND MODE
AUTO
POLLEN
SLEEP
LOW
MED
MAX
AUTO:
The fan speed is automatically switched depending on the amount of impurities in the air. You can select humidification ON / OFF.
POLLEN:
The Sensitive Dust Sensor sensitivity is automatically increased and the Sensitive Dust Sensor quickly detects impurities such as dust and pollen and cleans the air powerfully.
SLEEP:
The product will operate quietly, and the fan speed will automatically switch depending on the amount of impurities in the air and room brightness. When the Light Control is set to “Auto”, the Display and Cleanliness Indicator will automatically go off.

EN-12

ENGLISH

CLEAN ION SHOWER MODE
The product releases Plasmacluster ions with strong airflow and collects dusts while decreasing static electricity for 10 minutes. After that, the Sensitive Dust Sensor sensitivity is automatically increased and quickly detects impurities and clean the air powerfully for 50 minutes.

SWITCH DISPLAY
Humidity
Temperature
PM2.5 Concentration

NOTE
· When the operation finishes after 60 minutes, the product will return to the prior operation mode. It is able to change to other modes during this operation.
· The Plasmacluster ion cannot be turned “OFF”.

HUMIDIFICATION SETTING

ON

OFF

NOTE
· When operating with Humidification ON in the modes in the table below, the product automatically controls humidity by sensing temperature and humidity. (When the air volume is set to LOW, MED or MAX the product continues to humidify regardless of room conditions.)

Temperature (T)
T 18 ºC 18 ºC T 24 ºC 24 ºC T 28 ºC 28 ºC T

Humidity
65 % / 65 % 60 % / 65 % 55 % / 60 % 45 % / 50 %

• SLEEP Mode

CHILD LOCK

The operation panel will be locked.

(with the product ON or OFF)

ON

CANCELLATION

Press for 3 sec.

Press for 3 sec.

NOTE
· It is possible to turn Wi-Fi off while in Child Lock Mode.

WEEKLY SCHEDULER: APP ONLY
ON TIMER (or OFF TIMER)
You can set a weekly scheduler for the air purifier to start a specific mode (or to stop operation) on a specific day and time. The Timer Lamp will turn on while there is a schedule set.

EN-13

HOW TO CHANGE VARIOUS SETTINGS

· You can change the product and Wi-Fi functions on page 15 – 18.

1. Turn the product OFF.

Press for 3 sec.
When Wi-Fi setting Change “F” to “A”.

Product setting

Wi-Fi setting

4. When Wi-Fi setting
Refer to page 16 – 18 for the detail of each functions.

When Product setting Select “Setting number (01 – 03)” on page 15.

Go Forward

Go Back

or

Set

Set

Product setting

Wi-Fi setting

3. Select “Function number (F1-F7 or
A1-A8)” on page 15 – 18.

Go Forward

Go Back

or

Product setting
Wi-Fi setting
Set

5. Finish the setting.

Goes off

EN-14

ENGLISH

PRODUCT FUNCTIONS (F1-F7)

Function
Light Control
You can select the brightness of the Display and Cleanliness Indicator.
Plasmacluster Ion ON/OFF

Setting
OFF
When set to “OFF”, the “Dim” light illuminates for 8 seconds after operation starts and then the light goes off. However, some indicators that need notification will remain dim.
Dim
Auto (default)
Light automatically switches ON or OFF based on room brightness.
· Room is bright: light is ON · Room is dark: light is OFF Even though room is bright, the light will turn off when operating in sleep mode.
OFF
ON (default)

Auto Restart
If the product is unplugged or if there is a power failure, the product will resume operation with the previous settings after power is restored.
Adjusting sensor sensitivity (F4 – F6)
Light Sensor
Sensitive Dust Sensor
Odour Sensor
Sound Indicator Setting
You can set the product to make a beeping sound when the Water Tank is empty.

Cancellation ON (default)
Low Standard (default) High Cancellation (default) ON

EN-15

Wi-Fi FUNCTIONS (A1-A8)

Function

Setting

1. Select ” ” by following Steps 1 – 3 on page 14.

2. Press “SHARP LIFE AIR” Button to select Setting ” ” or ” “.

Wi-Fi OFF

Wi-Fi adapter ON/OFF

3. Complete

Wi-Fi ON
NOTE · When Setting number (” ” or ” “) is
changed, the square rotates on the display until the setting is completed. When setting is completed, ” ” is displayed.

Wi-Fi connection with a router (with the WPS Button)

1. Select ” ” by following Steps 1 – 3 on page 14.

2. After ” ” is displayed, press the WPS (Wi-Fi Protected Setup)
Button of the router.

Blink

Blink

Light up

weak

strong

Once connected, receiver level will be displayed.

A connection error is occuring if ” ” is displayed. Please confirm that the router is operating correctly and try again.

3. Complete

Initialization of Wi-Fi function

1. Select ” ” by following Steps 1 – 3 on page 14. 2. After ” ” is displayed press “Mode” Button.
An error is occurring if ” ” is displayed. Please try again.

Initializing Complete

3. Complete

Blink
NOTE · Please delete the device registration from the
App when initializing the air purifier which is already connected to the Wi- Fi.

EN-16

ENGLISH

Function
Confirmation of MAC address

Setting
1. Select ” ” by following Steps 1 – 3 on page 14. 2. Press “SHARP LIFE AIR” Button to display MAC address.
For example: In case MAC address is “12:34:56:AB:CD:EF”.
3. Complete

Display Wi-Fi network status

1. Select ” ” by following Steps 1 – 3 on page 14. 2. After displaying ” ” for a few seconds, network status of
Wi-Fi adapter will be displayed.
Connection is stable
Wi-Fi adapter is off Please turn on Wi-Fi adapter.
Router is not registered Please perform the Wi-Fi connection with the router.
Link settings with the App is not performed Please perform the link setting with the smart device.
Wi-Fi adapter network error Please turn off Wi-Fi adapter and turn on again after a while.
Network error between the air purifier and the router Please confirm the network status of the router.
Network service error Please turn off the air purifier and confirm the internet status, then try again.
3. Complete

EN-17

Function
Wi-Fi connection with a router (without the WPS Button) – AP (Access Point) mode –

Setting

1. Select ” ” by following the Steps 1 – 3 on page 14. 2. Perform Wi-Fi connection of the air purifier and the router based
on the App screen.

Refer to the App for further operations.
Blink Blink

Light up

Display while setting the connection between the product and the router.
A connection error is occuring if ” router and try again.

weak

strong

Once connected, receiver level will be displayed.

” is displayed. Please confirm the

CARE AND MAINTENANCE

CARE

· To maintain optimum performance of this air purifier, please clean the product including the filter periodically.
· Be sure to stop operation and unplug the product before any maintenance or replacing accessories.

2 14

6

5

3

4

Place

Page

1 Main Body

19

2 Water Tank

19

3 Humidifying Filter / Humidifying Tray 20

4 Back Panel / Sensors

19

5 HEPA Filter / Deodorizing Filter

22

6 Plasmacluster Ion Generating Unit

23

(Only UA-KIN52E)

EN-18

ENGLISH

FILTER MAINTENANCE LAMP
When the cumulative operation period or the water containing period is more than approximately 720 hours, the Filter Maintenance Lamp will turn on.
· It will not calculate the time when the product is unplugged.
· 30 days × 24 hours = 720 hours
This is a reminder to perform the maintenance described Humidifying Filter and Tray, Main Body, Back Panel, and Sensors.
After maintenance, connect the power plug to the wall outlet and press Power ON/OFF Button, then press and hold the Filter Reset Button for 3 seconds to reset the Filter Maintenance Lamp.

MAIN BODY / BACK PANEL / SENSORS

Wipe with a dry, soft cloth.

Remove the dust gently with a cleaning tool such as a vacuum cleaner.

Sensors

Sensors

Press for 3 sec.
WATER TANK
Rinse the inside with water.
NOTE How to clean hard to remove dirt. Clean the inside of the Water Tank with a soft sponge and the Tank Cap with a cotton swab or toothbrush.
Tank Cap Toothbrush

Back Panel (Pre-Filter)
NOTE · Do not apply excessive pressure when
scrubbing the Back Panel.

NOTE How to Clean Hard-to-Remove Dirt.

Back Panel
1. Add a small amount of mild kitchen detergent to water and soak for about 10 minutes.
2. Rinse off the mild kitchen detergent with clean water.
3. Completely dry the filter in a well-ventilated area.

Back Panel

Sensor Filter
1. Remove the Back Panel. 2. Remove the Sensor
Filter. 3. If the Sensor Filter is very
dirty, wash it with water and dry it thoroughly.

Sensor Filter

EN-19

HUMIDIFYING FILTER / HUMIDIFYING TRAY

REPLACEMENT AND MAINTENANCE CYCLE

Parts Name

Maintenance Cycle

Max Service Life Replacement Filter Model

Humidifying Filter

When odour emanates from the air outlet, or once a month.

10 years*1

UZ-KIL8MF

*1: Designated App notifies when each replacement part should be replaced according to usage.

MAINTENANCE
1. Remove the
Humidifying Filter and Tray.

2. Rinse with plenty of water.
· Do not remove the Humidifier Float. If it comes off, refer to page 21.
· Refer to page 21 for how to clean the Humidifying Filter when it is very dirty.
3. Attach the Humidifying Filter
and Tray.
· After maintenance, correctly reattach the parts.

Tray Panel Roller

Humidifier Float

Click

REPLACEMENT
See this page for directions on how to install the filter when replacing.
· Please consult your dealer for purchase of replacement filter. · Use only filter designed for this product. · Scan the QR code on page 5 for product information and accessories. When replacing the filter, making a memo of the start of use date is recommended.
Disposal of Filters
Please dispose of the replaced filter according to the local disposal laws and regulations. Humidifying Filter materials: Polyester, Rayon

UZ-KIL8MF (1 unit)
Humidifying Filter
Filter Frame
· Do not dispose the Filter Frame.

EN-20

ENGLISH

NOTE How to Clean Hard-to-Remove Dirt.

Mild Kitchen Detergent

Citric Acid

(only Humidifying tray)

(available at some drugstores)

1. Fill the tray half-way with 2 1/2 cups of water water.

1

2. Add a small amount of mild kitchen detergent.

100% Bottled Lemon Juice with No Pulp
3 cups of water

Soak for 30 minutes.
2

3 teaspoons

1/4 cup
Soak for 30 minutes.
(When using lemon juice as your descaling solution, allow for more soak time.)

3

Rinse off the mild kitchen detergent or the descaling solution with clean water.

NOTE How to install the Humidifier Float. Humidifier Float

Roller

3. Insert the tab on the other side of the Humidifier Float into the hole.
2. Insert the tab of the Humidifier Float into the hole.

1. Insert the Humidifier Float under this tab.
Cross-SectionTvaibew Humidifier
Float Cross-Section view

Click Click

EN-21

HEPA FILTER / DEODORIZING FILTER

REPLACEMENT AND MAINTENANCE CYCLE

Filter Name

Maintenance Cycle

Max Service Life

Replacement Filter Model

HEPA Filter Deodorizing Filter

Whenever dust accumulates, when odour emanates from the
air outlet, or once a month.

10 years*1, 2

UZ-HD4HF
UZ-HD4DF (Only UA-KIN42E) UZ-HG4DF (Only UA-KIN52E)

1: According to Japan Electric Manufacture’s Association JEM 1467, the Max service life is based on the equivalent condition of the smoke from 5 cigarettes per day whereby the dust collection/deodorization power is reduced by half compared with that of new filter. It is recommended to replace the filter more frequently under more severe conditions.
2: Designated App notifies when each replacement part should be replaced according to usage.
Filter life varies depending on the room environment, usage conditions, and location of the product. We recommend replacing the filter more frequently if the product is used in conditions significantly more severe (PM2.5 etc.,) than a normal household.

MAINTENANCE
Remove the dust on the filters.
NOTE · Do not wash the filters. Do not expose to
sunlight (Otherwise these filters may lose efficacy.)
HEPA FILTER
Maintain and clean only the tagged surface. Do not clean up the opposite surface. The filter is fragile, so be careful not to apply too much pressure.
Tag

REPLACEMENT

See page 9 for directions on how to install the filter when replacing.
· Please consult your dealer for purchase of replacement filter.
· Use only filter designed for this product. · Scan the QR code on page 5 for product
information and accessories.
When replacing the filters, making a memo of the start of use date is recommended.

UZ-HD4HF (1 unit)

UZ-HD4DF (1 unit)

UZ-HG4DF (1 unit)

DEODORIZING FILTER

Both surfaces can be maintained and cleaned. The filter is fragile, so be careful not to apply too much pressure.

(UA-KIN42E)

(UA-KIN52E)

Some odours absorbed by the filters will break down over time, causing additional odours. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odours may become noticeable sooner than expected. Replace the filter in those cases or if dust is unable to be removed after maintenance.

Disposal of Filters
Please dispose of the replaced filter according to the local disposal laws and regulations.
HEPA Filter materials: Polypropylene, Polyethylene
Deodorizing Filter materials: (Only UA-KIN42E) Polypropylene, Polyester, Activated carbon (Only UA-KIN52E) Paper, ABS resin
NOTE · Do not wash and reuse replaced filter.

EN-22

ENGLISH

PLASMACLUSTER ION GENERATING UNIT (Electrode Section)

REPLACEMENT AND MAINTENANCE CYCLE

Parts Name
Plasmacluster Ion Generating Unit*1

Maintenance Cycle
Every 6 months or more often if necessary

Max Service Life 19,000 hours*2,3

Replacement Model UZ-C90M

1: In the following, “Plasmacluster Ion Generating Unit” is abbreviated as “Unit”. 2: The replacement time will be announced by the Unit Replacement lamp. *3: Designated App notifies when each replacement part should be replaced according to usage.

MAINTENANCE
1. Remove the Unit Cover, and pull out
the Unit Holder.
Unit Cleaning Brush
2. Remove dusts from the Electrode
Section.
Unit Cleaning Brush Electrode

NOTE · Do not clean with anything other than the Unit
Cleaning Brush. Doing so could lead to failures in the Unit. · A bent electrode could be cut off and dropped during the cleaning process, but it will not change the performance. · Do not touch the electrode directly. Doing so could lead to pain / itching. · Do not transform the Electrode Section. Doing so can damage it. · Do not touch the Connection Terminals. Doing so can damage them.
Connection Terminals

Before cleaning

Electrode

After cleaning

Around the base
3. Insert the Unit Holder in the product,
and install the Unit Cover.

Click

REPLACEMENT

Unit Replacement lamp
When the total operation time exceeds 17,500 hours, the Unit Replacement Lamp will flash to indicate that the Unit needs replacement.

Operating time 17,500 hours

Explanation Replace the Unit

Flash slowly

19,000 hours Flash quickly

No Plasmacluster ions will be released by the Unit.

• The replacement time is not related to the selected operation mode.

EN-23

How to replace the Unit

· Please consult your dealer for purchase of a replacement Unit.
· Use only the Unit designed for this product.

UZ-C90M (1 unit)

1. Remove the claw of Unit Holder ( 1 ),
and remove the Unit ( 2 ).

2. Attach the New Unit.
· When the Unit has been replaced with a new part, the timer will be reset and return to 19,000 hours.
Disposal of the Unit
Please dispose of the used Unit according to the local disposal laws and regulations. Materials: Polybutylene Terephthalate, electronic parts

TROUBLESHOOTING
· Before calling for service, please review the Troubleshooting list below, since the problem may not be the product malfunction.
ABOUT THE PRODUCT
Odour and smoke persists.
· Check the filters. If they appear to be extremely dirty, clean or replace them.
Air discharged from the product has an odour.
· Check to see if the filters are extremely dirty. · Clean or replace the filters. · Use only fresh tap water. Using other water
sources risks the growth of mold, fungi, or bacteria.
The product does not operate when cigarette smoke is in the air.
· Make sure the product is installed in a location in which the sensors can detect cigarette smoke.
· Check to see if the Sensitive Dust Sensor openings are blocked or clogged. If they are blocked or clogged, clean the Sensor Filter or the Back Panel.
Smell from a new product and/or filter.
· Immediately after removing the plastic bag, a slight odour may occur. This odour is not harmful for filter performance or human exposure.
The product makes a clicking or ticking sound.
· The product may make clicking or ticking sounds when it is generating ions.
The Cleanliness Indicator is blue even when the air is not clean.
· The air may have been dirty when the product was plugged in. Unplug the product, wait one minute, and then plug the product in again.
The Cleanliness Indicator is red even when the air is clean.
· Dirty or clogged Sensitive Dust Sensor openings interfere with sensor operation. Gently clean the Sensor Filter or the Back Panel.

References

• Mobile applications - Intellectual property rights - Sharp Europe
• SENS eRecycling – Stiftung für Recycling von Elektro- und Elektronikgeräten
• Sharp Consumer Products Europe - Sharp Europe
• Swico - Der Wirtschaftsverband für die digitale Schweiz
• Sharp Consumer Products Europe - Sharp Europe
• Mobile applications - Intellectual property rights - Sharp Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>