SOLIGHT 1L68 Wireless bell User Manual
- August 13, 2024
- Solight
Table of Contents
- SOLIGHT 1L68 Wireless bell
- Product Information
- Product Usage Instructions
- Description
- Receivers
- Transmitter
- Installation
- Transmitter and receiver grouping options
- Troubleshooting possible problems
- Frequently Asked Questions (FAQ)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SOLIGHT 1L68 Wireless bell
Product Information
Specifications:
- Model : Solight 1L68 wireless doorbell
- Receiver Battery : 3x AA alkaline 1.5V pencil batteries
- Transmitter Battery : 3V CR2032 battery
- Maximum Pairing: 15 buttons to one bell; 1 button to 8 bells
Product Usage Instructions
Receiver:
- Open the battery cover and insert 3x AA alkaline 1.5V pencil batteries with correct polarity.
- Adjust melody and volume using the control buttons.
- The receiver can be placed freely on a surface or hung using the mounting hole. Do not cover the speaker.
Transmitter:
- To replace the battery, follow the instructions to open the back cover, replace the 3V CR2032 battery, and close the seal securely.
- Install the transmitter in a location protected from water and excessive heat using adhesive pads or screws.
Pairing Function:
- To pair a new transmitter to a receiver, follow the steps provided in the manual carefully.
- To unpair buttons from the receiver or reset the connection, follow the specific instructions outlined in the manual.
Dear customer, thank you for purchasing our product. Please read the following instructions carefully and follow them to serve you safely and to your full satisfaction. Avoid unprofessional handling of this device and always follow the electrical appliance usage policy. Keep the instruction manual carefully. For use in the home or indoors. Do not expose the receiver to environments with high humidity (e.g. bathroom), avoid contact with liquids.
Description
The receiver (doorbell) and transmitter (button) operate at a frequency of 433-433.92 ±1 MHz. The range is max. 200 m in open area.
Receivers
- Open the battery cover and insert 3x AA alkaline 1.5V pencil batteries.
- Observe the marked polarity. Adjust the melody and volume using the control buttons.
- The volume level changes from lowest to highest and back again, one beep is heard each time.
- The receiver can be freely stood up, laid down or hung on the mounting hole. Do not cover the speaker.
Transmitter
Replacing the battery
- Push the flathead screwdriver into the joint on the short side and open the back cover.
- Using your finger or a flathead screwdriver, release the latch also on the short side and swing the inner cover to the side.
- Unclip the seal protecting the battery from moisture ingress. Replace the 3V CR2032 battery, observing the marked polarity.
- Then close the seal and both covers carefully.
Installation
The transmitter is waterproof and can be placed outdoors. Prefer a location protected from water and excessive heat. The transmitter can be mounted on a pad using double-sided self-adhesive pads or screws with dowels, without or with a protective canopy.
Pairing function “Learning code”
The “Learning code” function allows you to pair several bells or buttons into
one group or to restore the connection between them. This allows several
buttons to ring one bell or one button to ring several bells. A maximum of 15
buttons can be paired to one bell. One button can be paired with up to 8
bells.
Assign a new transmitter to a receiver:
- Plug the receiver into a power outlet. Press and hold the button to change the melody for 3-4 seconds. The LED will flash rapidly. Release the volume button and allow the LED to flash.
- Bring the transmitter close to the receiver and press once. The selected melody will play. This assigns the transmitter to the receiver. The original transmitter is also assigned. Shown in Fig. 1.
Follow a similar procedure when assigning a new receiver to a transmitter. All previously paired receivers are also assigned to a transmitter. Shown in Figure 2.
Unpairing the buttons from the receiver, resetting the connection
If you have multiple transmitters paired to your receiver, there may be times
when you need to unpair one of the transmitters. It may also happen that the
wireless connection stops working.
-
Remove one battery from the receiver. Press and hold the button to change the tune while inserting the battery back in.
Keep the button pressed until the LED starts flashing rapidly. Then release the button. The connection memory is cleared.
The transmitters do not ring. -
Follow the procedure in the previous paragraph – Assigning a new transmitter to the receiver. Restore the connection.
Transmitter and receiver grouping options
Troubleshooting possible problems
If the receiver does not ring repeatedly after pressing a button on the transmitter, check:
- batteries. If necessary, replace with new ones.
- the distance between the transmitter and receiver is not too great.
- there are no strong sources of signal interference between the transmitter and receiver (radio and wireless networks, large metal objects, reinforced concrete walls, etc.).
Power supply | Doorbell | DC 4.5V, 3x AA (not included) |
---|---|---|
Push button | DC 3.0V, 1x CR2032 (included) | |
Power consumption | Doorbell | <0,5W idle mode/klidový/kľudový režim |
Push button | <10mW operating/pracovní/pracovný režim | |
Protection class | Doorbell | IP20 |
Push button | IP56 | |
Operating Temperature | Doorbell | -10°C/+45°C |
Push button | -15°C/+50°C | |
Optional melodies | Doorbell | 38 |
Volume/ | Doorbell | 25 – 110 dB(A) |
Signal range | max. 200m | |
Transmitting frequency | 433,92 ±1 MHz |
Manufacturer: Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500
06, info@solight.cz
Solight Holding s.r.o. declares that the product complies with the
requirements and provisions of Directive 2014/53/EU. The equipment can be
operated freely in the EU. The product can be operated on the basis of general
authorisation No.VOR/10/05.2014-3 Declaration of Conformity is at
www.solight.cz.
Frequently Asked Questions (FAQ)
Q: How many buttons can be paired with one bell?
A: A maximum of 15 buttons can be paired with one bell.
Q: How do I unpair a transmitter from the receiver?
A: Follow the steps to remove one battery from the receiver while pressing
the button to change the tune until the LED starts flashing rapidly. This
clears the connection memory.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>