SENECA MyALARM3 Cloud W-AIR Installation Guide
- August 12, 2024
- SENECA
Table of Contents
SENECA MyALARM3 Cloud W-AIR
FAQ
Q: What should I do if the MyAlarm3 Cloud W-AIR does not turn on?
A: Ensure the power supply is connected correctly and try restarting the device. If issues persist, contact technical support.
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol indicates conditions or actions that
put the user’s safety at risk. The word ATTENTION preceded by the symbol
indicates conditions or actions that might damage the instrument or the
connected equipment.
The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary
for its correct operation, and if the instructions contained in this manual
are not followed.
-
WARNING: The full content of this manual must be read before any operation. The module must only be used by qualified electricians.
Specific documentation is available using the QR-CODE shown on page 1. -
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to electrostatic discharges.
Take appropriate measures during any operation. -
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling). The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste.
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 – Fax +39.049.8706287
CONTACT INFORMATION
-
Technical support
support@seneca.it -
Product information
sales@seneca.it
This document is the property of SENECA srl. Copies and reproduction are
prohibited unless authorised. The content of this document corresponds to the
described products and technologies.
Stated data may be modified or supplemented for technical and/or sales
purposes.
MODULE LAYOUT
SIGNALS VIA LED ON FRONT PANEL
| LED | STATUS | LED MEANING |
|---|
NET (YELLOW)
| Off| WIFI off
Continuous fast flashing
|
Connection error to the WiFi network *()**
Continuous slow flashing
|
Access Point mode set
Flashing
|
Data sending
On| Connected to the WiFi router in Station mode
PWR (GREEN)| Off| MyAlarm3 W-AIR Cloud OFF
Flashing| Battery operation
On| MyAlarm3 W-AIR Cloud on and powered
- (*) Possible errors in the connection to the WiFi network:
- Entering an incorrect password
- Entering an incorrect SSID
- Excessive distance between the MyAlarm3 Cloud W-AIR control unit and the WiFi router
- Lack of WiFi signal due to shielding or network problems
- Failure or incorrect installation of the antenna on the control unit
SAFETY REGULATIONS
WARNING
- Do not apply different voltages or higher voltages than indicated between terminals, or between any terminal and earth (voltages greater than 50Vdc)
- Do not use the control unit if damaged, or if signs of possible damage are visible on it.
- Do not remove the internal battery.
- Do not use the control unit if it runs abnormally.
- Do not touch the control unit terminals during use
- For a correct use, use the cables supplied.
CAUTION
- Make sure the internal battery is charged if you intend to use the MyAlarm3 Cloud control unit without power.
- Use the MyAlarm3 Cloud W= AIR control unit as described in the manual downloadable at www.seneca.it/myalarm3-cloud-w-air.
- Before each use, refer to the electrical connections shown in the manual.
TECHNICAL SPECIFICATIONS
CERTIFICATES
|
---|---
Power supply
Voltage
|
6 – 15 Vdc; 500 mA Max.
Absorption| 3.5 W Max
Internal batteries| Lithium Ions 3.7 V, 1100 mAh, rechargeable non-
replaceable
Voltage output| +12 Vdc 50 mA (maximum current)
Temperature sensor| NTC thermistor (*)
Environmental conditions Temperature| Seneca recommends use at 0
to 45°C for correct operation
With the power supply present: -20 ÷ 55°C.
With use of the battery (when discharged): -20 ÷ 5°C Charging is possible in the range: 0 ÷ 45°C.
Humidity| 30%– 90% non condensing.
Storage temperature| From -20°C to 20°C < 1 year; from -20°C to 45°C < 3
months; from -20°C to 60°C < 1 month
Protection rating| IP20
Connections| Spring clamps, 3.5 mm pitch, connector for Micro USB and
SMA connector for WIFI Antenna
Slot Type / Memory Micro SD| Push-Push for micro SD card and SD HC card
/ max 32GB
Digital inputs Type Maximum frequency Threshold OFF Threshold ON|
4 inputs Reed, contact, PNP, Pulscap 30 Hz
0 ÷ 3 Vdc, I > 1 mA
6 ÷ 24 Vdc, I > 3 mA
Analog inputs| 2 inputs, Voltage 0 ÷ 30 Vdc / Current 0 ÷ 20 mA,
0.1% of full scale
Display| 128×32 LCD Dots with visible area of 39 mm x 8.6 mm
USB| 1 micro USB for configuration
WiFi| 2.4GHz (802.11b/g/n; Up to 150Mbps)
Digital outputs| 2 outlets Relay 3 A max – 250 V SPST (with shared
terminal)
To view all the product’s accessory tools, visit the dedicated page on the www.seneca.it website
CONTROL UNIT INSTALLATION AND FIRST ACTIVATION
CAUTION: to use this product it is necessary to use the dedicated “MyAlarm3 Cloud” APP downloadable via the QR Code on the cover or via the app store and apple store.
First startup procedure
- Download the iOS / Android APP (see QR Code on the cover or search for MyAlarm3 Cloud in the stores);
- Download the installation manual from the APP or from the QR Code on the cover to get the complete guide;
- Install the WiFi antenna supplied with the control unit (or external antenna: see the accessories section on the web page dedicated to the product) and check that the SD Card is correctly inserted;
- Connect the supplied power supply to the device and power the control unit. If the MyAlarm3 Cloud W-AIR does not turn on, press and hold the PWR button for a few seconds;
- When you turn it on for the first time, the device is in “Access Point” mode. The yellow “NET” LED lights up with a continuous slow flash and the writing “WiFI Access Point” appears on the screen;
- Using your mobile phone, connect to the WiFi network “MYA_XXXXXXXXXXXX” where the X r3epresent the MAC ADDRESS of the device Once connected to the control unit, open the address http://192.168.4.1 on the web browser to access the WEB SERVER of the MyALARM3 Cloud W-AIR and enter the SSID and Password of the WiFi network to which you want to connect;
- Once the association procedure has been completed, proceed with the activation of the Seneca cloud account by following the procedure below.
Simplified activation procedure (for complete procedure see the user manual)
- Open the MyAlarm3 Cloud APP, register your Seneca cloud account (if you don’t already have one) and wait for the account activation email;
- After receiving the account activation email, select the “ACTIVATE ACCOUNT” key;
- After activating the account, open the app again and log in for the first time entering the username and password you have just created;
- Enter the 5 + 10 character “activation code” on the back of the control unit and select the “ACTIVATE” button. If it is not the first service associated with the account, from the app click “change system” and then select the “ADD” button;
- From now on, the service is active and the control unit’s owner account can access the MyAlarm3 Cloud W-AIR system from the MyAlarm3 Cloud mobile app, as well as invite other users to use its newly activated MyAlarm3 Cloud W-AIR.
Switching on and menu keys:
The MyAlarm3 Cloud W-AIR is fitted with an ON/OFF PWR key positioned in the LH
top corner (Figure 2).
To switch it off, keep the PWR key pressed for a few seconds and then press
again to confirm switching off.
The device is fitted with a SCR key, in the RH top corner. Pressing this key
allows you to change the screen shown on the display. N.B.: In order to
guarantee the MyAlarm3 Cloud W-AIR control unit works correctly, THE CONTENT
OF THE SD CARD MUST NOT
BE REMOVED.
IMPORTANT: SENECA s.r.l. is not responsible for the times, methods or
non-delivery of reports (alarms, data, etc.) provided by the system via push
notification as these communications depend on the internet and/or telephone
connectivity services on which SENECA s.r.l. has no possibility of
intervening.
For any further information, consult the Cloud service supply contract.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>