VOLLRATH VOL-4076003 Meat Grinder Chamber Installation Guide
- August 11, 2024
- VOLLRATH
Table of Contents
VOLLRATH VOL-4076003 Meat Grinder Chamber
Specifications
- Model No.: 2350053-1
- Revision: 07/10
- Manufacturer: The Vollrath Company, L.L.C.
- Address: 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
Product Information
The meat grinder is designed for grinding meat and can be assembled and disassembled for cleaning and maintenance purposes. It consists of various components including a grinder chamber, blade shaft, worm gear assembly, knife blade, grinder plate, and coupling cover.
FAQ
Q: What should I do if I notice wear on the shaft washer?
A: If you notice wear on the shaft washer, replace it before further use to ensure safe operation of the meat grinder.
Q: Can I use cleaning products on the meat grinder?
A: Avoid using water or cleaning products directly on the unit as it may lead to electrical shock. Instead, clean and dry all parts thoroughly as per the instructions provided.
Q: Who should operate the meat grinder?
A: Only trained personnel should operate the equipment to prevent injuries from sharp blades. Always handle with caution and follow proper assembly and disassembly procedures.
Meat Grinder Chamber and Components Assembly and Disassembly
To ensure safe installation and operation, read the following statements and understand their meaning. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.
Safety Precautions
WARNING
Electrical Shock Hazard.
Keep water and other liquids from entering the inside of the unit. Liquid
inside the unit could cause an electrical shock.
Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock. Do not use unit if power cord is damaged or has been modified. Do not use an extension cord with this unit.
WARNING
Sharp Blade Hazard.
Blades are sharp and can cause cuts and amputation.
To avoid injury from sharp blades, handle with caution. Only trained personal should operate equipment or preform maintenance.
ASSEMBLY PROCEDURES
-
Turn the meat grinder off and unplug from its power source.
-
Thoroughly clean and dry all parts.
-
If necessary assemble the blade shaft (B) into the worm gear (A). See Figure 1.
-
Inspect the shaft washer (A) for wear. See Figure 2. Replace if necessary.
-
Slide the shaft washer (A) onto the worm gear shaft (B).
-
Slide the shaft washer (A) so that it is seated against the worm gear assembly (B) as shown. See Figure 3.
-
Slide the worm gear assembly (B) and the shaft washer (A) into the grinder chamber (C). Slide the worm gear shaft (D) in until it is seated fully.
-
Slide the knife blade (B) so that the flat ground edges (A) face to the outside as shown, onto the blade shaft (C). See Figure 4.
-
Slide the knife blade (B) onto the blade shaft (C) so that it seats completely over the square (D). See Figure 5.
-
Place the grinder plate (D) onto the blade shaft (A) so that the cutout (C) slides over the locating pin (B). See Figure 6.
-
If a sausage filler is to be used, place it between the coupling cover (A) and the grinder chamber (B). See Figure 7.
-
Thread the coupling cover (A) onto the grinder chamber (B) and tighten securely.
Disassembly Procedures
- Turn the meat grinder off and unplug from its power source.
- Unscrew and remove the coupling cover (A) from the grinder chamber (B). See Figure 7.
- Remove the grinder plate (D) from the blade shaft (A). See Figure 6.
- Carefully remove the knife blade (B) from the blade shaft (C). See Figure 5.
- Remove the worm gear assembly (B) from the grinder chamber (C). See Figure 3.
- Thoroughly clean and dry all parts.
The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201
U.S.A.
Main Tel: 800.628.0830
Fax: 800.752.5620
Technical Services: 800.628.0832 Service Fax: 920.459.5462
Canada Service: 800.695.8560
© 2010 The Vollrath Company, L.L.C.