COMFAST CF-EW84 Outdoor AP Gigabit Access Point Installation Guide

COMFAST CF-EW84 Outdoor AP Gigabit Access Point

Product Information

Specifications

• Model: [Insert Model Number]
• Compliance: FCC Regulations
• RF Exposure Limit: FCC radiation exposure limits for uncontrolled environments
• Recommended Distance: Minimum 20cm between radiator and body

Product Usage Instructions

Installation

1. Place the equipment on a stable surface.
2. Ensure there is at least a 20cm distance between the radiator and your body when operating.
3. Connect the necessary cables and power source as per the user manual.
4. Power on the equipment following the specified instructions.

Operation

1. Use the equipment in accordance with the provided guidelines.
2. Maintain the recommended distance of 20cm between the radiator and your body during operation.
3. Monitor the equipment for any unusual behavior or malfunctions.
4. Follow proper shutdown procedures when not in use.

Maintenance

1. Regularly clean the equipment using a soft, dry cloth.
2. Avoid exposing the equipment to extreme temperatures or moisture.
3. Refer to the user manual for specific maintenance tasks and schedules.

FAQ (Frequently Asked Questions)

• Q: What is the recommended distance between the equipment and the body?
  

  • A: The recommended minimum distance is 20cm to comply with FCC radiation exposure limits.

• Q: How should I clean the equipment?
  

  • A: Use a soft, dry cloth to clean the equipment regularly. Avoid using harsh chemicals or abrasive materials.

Outdoor AP
Quick Installation Guide

Outdoor AP
M 03046 3 6Version 6.0

1. Please set automatically get ip for the computer, connect the ap Ian port to the setting page.

2. Set the computer to obtain the IP address automatically, and connect the LAN port of the device to the device management interface.

3. The device is defaulted to the interface Router mode .
   The steps to enter the setup page as follows:
   (Note: Please connect the wireless network management page to the single network port device)

4. Under default configuration, power on the device and wait for the device to start for 90 seconds.

5. Connect device wireless SSID (default is COMFAST_XXXX:_2G, XXXX is the last 4 digits of the MAO.

6. Input 192.168.10.1 in the web browser to get into the setting p age.

7. Open the computer browser, and input 192.168.10.1 to get into the device login page (Default username: admin Default password: admin). The device language is compatible with
   Chinese and English to choose, and you can set up the language by the top right corner icon

8. When getting into the setting page, there are four working modes in the Wizard: AP Mode, Bridge Mode, Router Mode, Repeater Mode.

9. Click AP mode and set up IP Address and Subnet Mask. The IP address and Subnet mask should be within the same network segment as upper network and can’ t be conflict with IP address from upper network router. After settings, you can visit the device from the IP address you have set just now by connecting internet with WAN port of the device or POE adapters LAN port.
   CD Notes : In AP mode, the IP address from the other devices connected the AP will be allocated by the upper network router.
   @The AP needs to set an intra-net IP address (do not set the same IP address as the upper router). If want to manage the device, Manually set the IP address of the same network segment of the intra-net IP.

10. A PM ode: You can setup 2 .4Gwireless SSID, password, channel and country in advance. After setting up, the device’ s WAN p ort or POE adapter LAN p ort connected internet, other mobile devices can connect the SSID to surf the internet.

11. Bridge Mode: Pis ensure the W DS in upper network is enabled. AP device can set up intranet segment(do n ot set the same IP address as the upper router), and then select their less SSID signal you need to bridge and input wireless password.
    (Notes: The password is same as your upper network router) Pis set the SSID and password for the device and click “Next” o finish settings.

12. 8 . Repeater Mode : The AP device can set the internal network segment (the gateway IP should not be the same as the upper device gateway IP). Next, select then of the wireless SSID signal that you need to relay and input wireless password.
    (Notes: The password is same as your upper network router). Pis set the SSID and password for the device and click “Next” o finish settings.

13. Router Mode: There are three ways to surf the internet: PPPOE, Static, and DHCP. (Pis refer to router setting as reference)

Quick Installation Guide

Statement

Shenzhen Four Seas Global Link Network
Technology CO., Ltd. Company all rights reserved.

Without ours official writ permission, no unit or individual shall be copied, reproduced, transcribed or translated in part or whole book. In any form or by any means(electronic, mechanical , printing, record­ing or other possible means)or for the propagation of goods any commercial, profitable purposes.

CDMFAST is the registered trademark of Shenzhen Four Seas Global Link Network Technology Co .• Ltd .Company. All other trademarks or registered trademarks mentioned in this document, by respective owners.

Product specifications and information mentioned in this manual are for reference on subject to updates without notice. Unless there are other special agreed, this manual is used only as a user guide. All statements, information, etc. are not constitute any form of guarantee.

• Manufacturer: Shenzhen Four Seas Global Link Network Technology Co .• Ltd. Company
• Address: Room 607-610.Block B Tao JINDI Electronic
• Business Incubation Base, Tenglong Road, Longhua District, Shenzhen, China
• Hotline: 0755 83790059/83790659
• Website: www.szcomfast.com

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimumdistance20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>