PRORECK PR Series Concert and Venue Set User Manual

: August 11, 2024
: PRORECK

Table of Contents

PRORECK PR Series Concert and Venue Set
INTRODUCTION
BOX CONTENTS
CONNECTION OF CONCERT SET
VENUE SET
CONNECTION OF VENUE SET
FUNCTIONS -SUBWOOFER
FUNCTIONS -ARRAY SPEAKER
DSP SETTINGS
SPEAKER SET UP
SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PRORECK PR Series Concert and Venue Set

WARNING

Do not open cover. No user-serviceable parts inside. Refer servicing to qualified service personnel.
Do not place the product in a location near a heat source, such as a radiator, or in an area subject to direct sunlight, excessive dust, mechanical vibration or shock.
The product must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product.
No naked flame sources, such as lighted candles, should be placed on the product.
Allow adequate air circulation and avoid obstructing vents (if present) to prevent internal heat build-up. The ventillation must not be impeded by covering the appliance with items such as newspapers, table-cloths, curtains etc.
The mains plug is used to disconnect the appliance from the mains supply. Ensure that the mains outlet is easily-accessible and remove the plug from the mains outlet if you notice any abnormality with the appli-ance.

IMPORTANT RIGGING INFORMATION

Installation should be carried out by qualified personnel only. Improper installation can result in serious injury and damage to property.
Overhead rigging requires extensive experience. Working load limits should be respected and certified installation materials would be used.
The installation should be inspected regularly for safety.
Make sure that the area below the installation is free from personnel during rigging, de-rigging & servicing. The device should be installed out of reach of people and away from areas where persons may walk by or be seated.

INTRODUCTION

Thank you for purchasing our product. To get the most out of your product, please read this manual care-fully.
SUBWOOFER

Powerful 12” twin cone subwoofer perfect for small to mid sized venues and outdoor.
Includes 96KHz, 48-BIT DSP processor with four preset frequency curves.
Connect a variety of sources via two combo XLR/Jack inputs.
Independent satellite speaker and subwoofer volume controls guarantee optimised sound reproduction.
Effortlessly switch between mono and stereo playback at the touch of a button.

ARRAY SPEAKER

Boasts serial/parallel connection technology.
Position without compromise via multi-angle line array positioning system.
Robust construction withstands the rigours of live performance.

BOX CONTENTS

BOX MODEL	CONTENTS
PR-212T	1 x subwoofer

1 x power cord (6-feet)

PR-15S| 2 x tripod stand

PR-ADAPTER

| 2 x adapter

2 x speakon to 6.35mm cable (10-feet) 2 x 6.35mm array cable (8-inch)

4 x 6.35mm array cable (14-inch)

PR-204V| 4 x array speaker
PR-204V| 4 x array speaker

CONNECTION OF CONCERT SET

When you use this way of connection, it is necessary for you to release the button (as circled in the picture) to stereo.

VENUE SET

This set includes 7 packages.

BOX MODEL	CONTENTS
PR-212T	1 x subwoofer

1 x power cord (6-feet)

PR-212T| 1 x subwoofer

1 x power cord (6-feet)

PR-204V| 4 x array speaker
PR-204V| 4 x array speaker
PR-204V| 4 x array speaker
PR-204V| 4 x array speaker

PR-FLY CASE

| 1 x FLY CASE

4 x speakon to 6.35mm cable (10-feet) 4 x 6.35mm array cable (14-inch)

8 x 6.35mm array cable (8-inch)

FLOWN/ABOVE HEAD HEIGHT
HEIGHT FROM FLOOR: 3+ METRES
AUDIENCE COVERAGE: 500+ PEOPLE

CONNECTION OF VENUE SET

When you use this way of connection, it is necessary for you to press the button (as circled in the picture) to mono.

FUNCTIONS -SUBWOOFER

SUBWOOFER LEVEL
Adjust this knob for independent control over the subwoofer.
SATELLITE LEVEL
Adjust this knob for independent control over the satellite speakers.
INPUTS
Use these combi-jack inputs to connect line-level sources such as mixing consoles.
LINE OUT
Use these XLR outputs to send your signal to another subwoofer or system.
VOLTAGE SWITCH (115V/220V)
When powering on please ensure that the indicated voltage matches your supply. Please note that the wrong voltage can cause serious damage to your unit.
SPEAKER SOCKETS (NL4)
Use these sockets to connect your subwoofer with the satellite speakers.
DSP INDICATOR
These LEDs indicate which DSP preset is engaged.
DSP PRESET
The DSP knob allows you to choose from one of four presets.
• STANDARD
• DJ 1
• DJ 2
• LIVE
BLUETOOTH SWITCH
Press the Bluetooth switch. If the connection is successful, the blue light will stay on. If the connection fails, the blue light will keep flashing.
If you want to use the TWS mode, then press and hold the Bluetooth switch for three seconds until the red light turns on. If the red light is blinking, the connection is not successful. If the red light is on, the connection is successful.
STEREO / MONO BUTTON
This button allows you to alternate between stereo and mono playback to suit the needs of your performance and environment. When engaged the signal is summed to mono. When disengaged the signal is heard in stereo.
POWER SWITCH
Use this switch to turn the unit on and off.
MAIN POWER INPUT
Use the supplied mains cable to provide power to the unit via a mains socket. Please note only use the same type of fuse that comes installed from the factory (T5AL 250V).

FUNCTIONS -ARRAY SPEAKER

SERIES OUT
Adjust this switch to determine whether the signal is provided from one speaker to the next in either series or parallel.
INPUT
Provides input to the speaker from the subwoofer or another satellite via ¼” TS Jack.
PARALLEL OUT
Provides output for a parallel connection via ¼” TS Jack.
SERIES OUT
Provides output for a serial connection via ¼” TS Jack.

DSP SETTINGS

STANDARD
A clear and accurate sound. The low and high roll-offs, combined with a slight mid cut give clarity making this setting ideal for theatrical or speech orientated events.

Examples

Theatrical productions
Awards and dinner events

DJ 1
Boosts the bass to help drive dance music and enhance your party’s atmosphere. Ideal for larger venues.

Examples

DJ and Club events
Larger venues

DJ 2
Cut through audiences for a pronounced sound, With low and high end boosts and a slight mid cut

Examples

Pre-recorded music
Mixed media events such as weddings or parties

LIVE
Designed to give energy and brightness to live musical performances, with high and low end roll-offs to lightenthe sound.

Examples

Live bands or solo performances
Small to medium sized outdoor / venue stages

SPEAKER SET UP

Insert the front pillar into the slots at the bottom of the speaker. This allows you to connect the speaker to the stand adapter. Please ensure that both holes are aligned before doing so
Achieve the speaker angle you desire by aligning the holes to your intended placement and then inserting the safety pin. Please ensure this is fully inserted before letting go.
To connect the front of the speakers, lift the bottom to ensure that the bracket aligns with the hole in the top speaker and fully insert the safety pin. Then adjust the angle you desire.
When not in use secure the pins into the spare holes.

When using the ﬂying frame please consult a trained professional.