BEKO RHO8122T Oil Filled Heater User Manual

BEKO RHO8122T Oil Filled Heater

This product is only suitable for well insulated spaces or occasional use.

Please read this user manual first!
Dear Customer,
Thank you for preferring a Beko product. We hope that you get the best results from your product which has been manufactured with high quality and state-of- the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use. If you handover the product to someone else, give the user manual as well. Follow all warnings and information in the user manual.

Meanings of the symbols
Following symbols are used in the various section of this manual:

Important safeguards

When using any electrical appliance, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following:

• Read all instructions before using heater.
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surtaces. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the heater. Allow heater to cool before moving and then use the built-in handle for easy movement.
• Extreme caution is necessary when heater is used by or near children and whenever heater is left unattended.
• Always unplug the heater when it is not in use.
• Do not operate any heater with a damaged cord or plug, or after the heater malfunctions, or has been dropped or damaged in any manner. Return heater to the manufacturer for examination, electrical or mechanical adjustment, or repair.
• Do not use heater outdoors. This product is intended for normal household indoor use only.
• This heater is not intended for use in bathrooms, laundry areas or similar moist indoor locations. Never locate heater where it may tall into a bathtub or other water container.
• Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over.
• To disconnect heater, set controls to Off, then remove plug from outlet.
• Keep this heater clean. Do not allow foreign objects to enter any ventilation or exhaust opening as this may cause electric shock, or fire, or damage the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked
• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.

Warning: In order to avoid overheating, do not cover the heater.

• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• The heater must not be located immediately below a socket- outlet.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Correct disposal of this product
This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used device must be returned to official collection point for recycling of electrical and electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was purchased. Each household performs important role In recovering and recycling of old appliance. Appropriate disposal of used appliance helps prevent potential negative consequences for the environment and human health.

• This heater is filled with a precise quantity of special oil. Repairs requiring opening of oil-container are only to be made by the manufacturer or his service agent who should be contacted if there is an oil leak. When scrapping the heater, follow the regulations concerning the disposal of oil.
• Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning .

use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

Warning: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
Warning: In order to avoid overheating, do not cover the heater.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not use this heater if it has been dropped;
• Do not use if there are visible signs of damage to the heater; Use this heater on a horizontal and stable surface.
• Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
• Do not use the heater in green house and building sites.
• If you are not using the heater, switch off and plug out.

Part figure

1. Control panel
2. Display screen
3. Control knob
4. Power switch
5. Air inlet
6. Thermovent
7. Cordwrap
8. Wheel assembly
9. Rear cover
10. Radiators

Assembly instructions

Unpack your heater and find the wheel-holding plate and butterfly nuts between the fins assemblies.

1. Make sure the heater is unplugged and in the “Off” position.
2. Turn the heater upside down.
3. Attach the wheel-holding plates onto the heater as Fig. 1 shows. The U plate is fixed between the last tow fins and the other one is fixed under metal control box. Fix the castors to the vertical axis of both the wheel holding plates.
4. Insert the butterfly nuts and tighten them securely.
5. Turn the heater upright. Your heater is now ready to use.

Warning: Risk of fire. Do not operate heater without wheel assemblies attached Operate heater in upright position only (wheels on bottom, controls on top). Any other position could create a hazardous situation. Ensure that the surface beneath the heater is clean and free of any obstructions. It is not recommended that this heater be placed on high-pile carpeting or any other surface that impedes the flow of air underneath the heater.

Operation

Power on the heater, press the Power switch at the lower side to On position, the power indicator lights on and buzzer makes sound to enter into the standby mode.

[On/Off]
Under Standby mode, press the knob (or remote controller button), the heater enters into the Normal mode, works with highest power, and automatically set the temperature at 35°C, or recover to the state of the last standby state (Note: when the power is not cut off). Repeatedly press the knob untill the heater recovers to the Standby state.

[Mode Switch]
Under Working State, press the button M, the heater switches between Low — Middle– High–Fast-Heating Mode — Energy Saving Mode — Anti-Freezing Mode — Low. Orrepeatedly press the remote controller button to switch between Normal Mode — Fast-Heating Mode — Energy Saving Mode — Anti-Freezing Mode — Normal Mode.

[Level Switch]
Under Working State, press the button M, the heater switches between Low – Middle– High – Fast-Heating Mode — Energy Saving Mode — Anti-Freezing Mode — Low.
Or under normal mode, repeatedly press the remote controller button to switch between High (orange) — Middle (red) — Low (green) — High (orange).

[Temperature setting]
Under Normal mode, press the button to check the current setting temperature, and the temperature icon flashes. Turn the knob to adjust the setting temperature, it will automatically exit the enquiry setting interface if it is not operated within 3s, and display the setting temperature.

[Timing On]
Under Off state, press the button (or remote controller button) to enter into the timing enquiry interface, the setting time and timing icon flashed, turn the knob to adjust the setting time, it will ” automatically exit the enquiry setting interface if it is not operated within 3s. When the setting is O, it cancels Timing On.
After reaching the Timing On time, the heater automatically turns on and works at the last standby state. The time setting range is 0-24H, the adjustment unit in hour.

[Remote ] When working mode is on, press the & button on control panel, press “a” ” to adjust temperature within 5°C to 35°C. Press the © button on remote controller, press “ ” to adjust time within 0 to 24 hours.

[Introduction on mode]
Normal mode : under this mode, the heater works at the setting level, after reaching the setting temperature, it stops heating and the setting temperature flashes. Energy saving mode ECO: under this mode, the heater works normally, the level and setting temperature are not adjustable, the heater works at default setting temperature (22°C). (In Energy saving mode, if the setting temperature flashes, it means the heater is under energy saving heat preservation work state). The indicator light circle indicates green.
Anti-Freezing mode under this mode, press the knob to adjust the level, but the setting temperature is not adjustable, the heater works at default anti- freezing temperature (5°C). (In Anti- Freezing mode, if the setting temperature flashes, it means the heater is under anti-freezing heat preservation work state). The indicator light circle indicates red

[Memory Function]
When the power of the heater is not cut off or the heater keeps under Standby mode, it can memorize the last working mode and setting temperature and works at the setting temperature after turning on, the memory data will be reset if the power supply of the heater is cut off, and the setting temperature of the heater recovers to the default setting (Normal mode, high, setting temperature is 35°C) when turning on.

Inserting batteries

1. Press down on the battery compartment cover and slide it out.
2. Insert the batteries, making sure that the positive terminals are facing the proper direction marked inside the battery compartment.
3. Close the cover by sliding it in.

Note:

1. Use 2 “AAA” batteries (not included).
2. Do not mix old and new batteries.
3. Do not mix alkaline, standard (carbon-line) or rechargeable (nickel-cadmium) batteries.
4. Remove the batteries from remote if is to be left unused for a long period of time.

Warning : This heater includes a thermal cut-off that shuts the heater off if it overheats due to abnormal conditions. If this occurs, turn the heater “off”, unplug it, and inspect and remove any objects on or adjacent to the heater. Allow it to cool for a few minutes, and then plug it back in and resume normal operation.

Others

Saftey features
Thermal cut-off: This heater includes a thermal cut-off that shuts the heater off if it overheats due to abnormal conditions. If this occurs, turn the heater off, unplug it, and inspect and remove any objects on or adjacent to the heater. Allow it to cool for a few minutes, and then plug it back in and resume normal operation. Tip-over switch: This heater includes a safety tip- over protection feature that will shut the heater off in case it is tipped over. If, at any time, the heater tips over, please put the heater back in the upright position. The heater will resume its normal operation.

Cleaning and maintenance instruction

1. The electric heater should be cleaned regularly to wipe out the dust on the surface of flanges. As this may influence the radiating efficiency.
2. Disconnect electricity supply and allow radiator to cool, wipe out dust with a soft damp cloth. Do not use detergent or abrasives.
3. Do not scrap the surfaces of flanges with sharp hard tools, to avoid surfaces getting rusty, because of damage of the paint coat.

Main technology specifications
Power supply: AC220-240V ~ 50Hz

Manufactured by Arcelik A.S. Karaagac Cd. No:2-6 34445 Sutluce, Beyoglu, Istanbul, Turkey

• All performance parameters in the table above were measured before delivery and are for reference only.

Table 2
Information requiremente for electric local snace heaters

www.beko.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>