Einhell 504396 Pneumatic Impact Wrench Tc Pw Compact Instruction Manual

: August 10, 2024
: Einhell

Table of Contents

Einhell 504396 Pneumatic Impact Wrench Tc Pw Compact
Product Usage Instructions
Technical data
Before starting the equipment
Operation
Cleaning, maintenance and ordering of spare parts
Warranty certiﬁcate
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Einhell 504396 Pneumatic Impact Wrench Tc Pw Compact

Specifications

Model: TC-PW 610 Compact
Operating Instructions Languages: German, English, French, Italian, Swedish, Dutch, Spanish, Slovenian, Greek, Croatian, Serbian, Polish
Art.-Nr.: 41.389.65
I.-Nr.: 21011

Product Usage Instructions

Safety Instructions
Ensure to wear the necessary protective gear, especially safety goggles while working with the screwdriver. Follow all safety regulations.

Tool Attachment/Removal
Insert the desired tool (not included) into the air pressure connection (9).

Operation

Connection to Air Supply: Connect a quick coupling of an air hose (hose not included).
Direction/Torque Switch: Turn the direction switch (2) to switch between clockwise and counterclockwise rotation. Adjust the torque by turning the adjustment wheel (8). Note that torque adjustment is only possible in clockwise rotation.
Fastening/Loosening Screws: Turn on the air supply and connect the screwdriver (refer to step 2). For fastening, adjust torque and direction accordingly.

Cleaning, Maintenance, and Spare Parts Ordering

Cleaning: Clean the screwdriver after each use to maintain performance.
Maintenance: Refer to the user manual for maintenance guidelines.
Spare Parts Ordering: When ordering spare parts, provide the necessary details. Visit www.Einhell-Service.com for current prices and information.

Frequently Asked Questions (FAQ):

Q: Can I adjust the torque of the screwdriver?
- A: Yes, you can adjust the torque by using the adjustment wheel (8) in clockwise rotation mode.
Q: How should I clean the screwdriver?
- A: Clean the screwdriver after each use following the cleaning instructions provided in the user manual.

TC-PW 610 Compact

Original operating instructions Air hammer screwdriver

Danger!

When using the equipment, a few safety pre-cautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Explanation of the symbols used (see Fig. 5)

Danger! – Read the operating instructions to reduce the risk of injury.
Caution! Wear ear-muﬀ s. The impact of noise can cause damage to hearing.
Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!
Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
Each time before use, oil the compressed air tool via the compressed air coupling.
Direction of rotation
Torque selector.

Safety regulations
The corresponding safety information can be found in the enclosed booklet.

Warning!

Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, ﬁ re and/or serious injury.
Keep all the safety information and instructions in a safe place for future use.
Protect yourself and your environment from risks and accidents by taking the appropriate precautionary measures.

Layout and items supplied

Layout (Fig. 1-4)

****Trigger lever
Switch for setting forward/reverse rotation
Square driver mount for connector
Nipple
Oil bottle (without oil)
Plug-on attachments (sizes: 17 mm, 19 mm, 21 mm)
Thread sealing tape
Setting wheel for setting the torque
Compressed air connection

Items supplied
Please check that the article is complete as speciﬁed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or transportation braces (if available).
Check to see if all items are supplied.
Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period.

Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of
swallowing or suﬀocating!

Pneumatic impact driver
Nipple
Oil bottle (without oil)
Plug-on attachments (3 items)
Thread sealing tape
Original operating instructions
Safety information

Proper use
The impact driver is a handy, pneumatically operated tool designed for DIY applications. It is suitable for fastening and releasing threaded connections.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

Remember.
Too small a diameter of the hose and too long a hose line will result in loss of power.

Technical data

Max. loosening torque . ……………………….610 Nm
Max. torque ………………………………………610 Nm
Working range (max. thread size) ……………. M18
Recommended operating pressure ……… 6.3 bar
Max. permissible working pressure ………… 8 bar
Idling speed ………………………………….9000 min-1
Square drive mount …………….12.7 mm (1/2 inch)
Air consumption ……………………………. 142 l/min.
Recommended hose diameter ………………. 9 mm
Weight ………………………………………………..1.2 kg

Sound and vibration
Sound and vibration values were measured in accordance with EN ISO 15744.

LpA sound pressure level …………………… 95 dB(A)
KpA uncertainty ……………………………………… 3 dB
LWA sound power level ……………………. 106 dB(A)
LWA sound power level ……………………. 106 dB(A)

Wear ear-muﬀ s.

The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) were determined in accordance with EN ISO 12096 and EN ISO 28927-2.
Vibration emission value ah = 3.8 m/s2
K uncertainty = 1.5 m/s2
The speciﬁed vibration value was established in accordance with a standardized testing method. It may change according to how the electric equipment is used and may exceed the speciﬁed value in exceptional circumstances.
The speciﬁed vibration value can be used to compare the equipment with other electric power tools.
The speciﬁed vibration value can be used for initial assessment of a harmful eﬀ ect.

Keep the noise emissions and vibrations to a minimum.

Only use appliances which are in perfect working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.

Caution!
Residual risks
Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout

Lung damage if no suitable protective dust mask is used.
Damage to hearing if no suitable ear protection is used.
Health damage caused by hand-arm vibrations if the equipment is used over a pro-longed period or is not properly guided and maintained.

Before starting the equipment

Before you connect the equipment to the power supply make sure that the data on the rating plate are identical to those of the supply voltage. Disconnect the compressed air supply before performing any cleaning, adjusting and maintenance work.

Air supply
Via a compressed air source with pressure setting function, e.g. a compressor. Before starting up, please also read the section on care and maintenance.

Performance values of the compressor:
The compressor used should have a tank volume of at least 50 liters.
Setting values for work with the suction spray gun
Set a maximum working pressure of 8 bar at your compressed air supply.

Remember
Wear the necessary protective clothing, in particular safety goggles, when working with the screwdriver.
Pay attention to the safety regulations.

Lubricating the tool
Each time before starting and during prolonged operation

Insert 3-5 drops of special compressed air oil (not included in delivery) into the compressed air connection (9)
Let the equipment run briefly so that any sur-plus oil is blown out.

Inserting/removing a tool (Fig. 1)

Fit the required drive socket insert by pushing onto the square drive mount (3).
Remove the drive socket insert by pulling it oﬀ the square drive mount (3).

Operation

Connecting to a compressed air supply

Connect the nipple (5) to the quick-lock coup-ling of a compressed air hose (the hose is not supplied).
Note the maximum permissible operating pressure of the equipment.

Rotational direction switch/torque switch (Fig. 4)
You can select clockwise or counter-clockwise rotation by turning the rotational direction switch (2).
Turn the setting wheel (8) in order to set the torque. Please note that the torque can be set only in clockwise rotation.

Low torque
Medium torque
High torque

In counter-clockwise rotation there is one level for undoing the screws.

Important!
To avoid gear damage, make sure that the tool has come to a complete stop before you change the direction of rotation.

Working with the impact driver Loosening

Set the direction of rotational direction switch (2) to counter-clockwise.
Mount a drive socket insert on the impact driver (see point 5.2).
Place the impact driver on the screw/nut and press the trigger lever (1).
If the screws/nuts are very tight or if they are rusted, use a tire wrench or torque wrench to slightly loosen them.

Tightening

Warning! Use the impact driver only for loosening screws/nuts. If you want to use the impact driver to tighten screws and nuts, you must also use a torque limiter which is designed for this purpose. If not, the screw connection may be damaged. The torque limiter is available from your dealer. It is not included in the scope of this delivery.
Prior to tightening, carefully insert the screw/nut into the threads.
It is important that screws/nuts with special torque specifications (for example provided by the vehicle manufacturer in the automotive sector) are tightened only with a suitable torque limiter.

Danger!
Screws/nuts must be ﬁnish-tightened with a torque wrench which is set to the torque speciﬁed by the manufacturer and then they must be checked!

Cleaning, maintenance and ordering of spare parts

Disconnect the compressed air supply from the equipment before performing any cleaning work.

Cleaning

Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it down with compressed air at low pressure.
We recommend cleaning the equipment immediately each time after use.
Clean the equipment regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plastic parts in the equipment. Ensure that no water can get into the interior of the equipment.

Maintenance Warning!

Disconnect the equipment from the compressed air supply before you carry out any maintenance or cleaning work.
Compliance with the maintenance instructions listed here will help this quality product provide you with a long service life and trouble-free operation. Regular lubrication is essential for your equipment to work properly for a prolonged period of time.
Regularly check the speed and the vibration level by simply observing the tool.

Note: Use environmentally friendly compressed air oil if you want to operate the equipment outside the workshop.

The following lubrication options are available

Lubrication by mist oiler
Connect a mist oiler between the compressed air source and the equipment (not supplied, available at retail stores)

By hand

Each time before using the compressed air tool insert 3-5 drops of special compressed air oil into the compressed air connection. If the compressed air tool has not been used for several days you must insert 5-10 drops of special compressed air oil into the compressed air connection before switching on.
Store your compressed air tool only in a dry room.

Other maintenance
There are no other parts inside the equipment which require maintenance.

Excluded from the guarantee are

Wear parts
Damage cause by too much operating pressure.
Damage caused by non-conditioned compressed air.
Damage caused by improper use or unauthorized intervention.

Ordering replacement parts
Please quote the following data when ordering replacement parts

Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required For our latest prices and information please go to www.Einhell-Service.com

Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council oﬃces.

Storage

Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.
Subject to technical changes

Service information

We have competent service partners in all countries named on the guarantee certiﬁcate whose contact details can also be found on the guarantee certiﬁcate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Category	Example
Wear parts*	Connector
Consumables*	Plug-on attachments, extension
Missing parts

Not necessarily included in the scope of delivery!

In the eﬀ ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com . Please ensure that you provide a precise description of the problem and answer the following questions in all cases

Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) prior to the failure?
What malfunction does the equipment have in your opinion (main symptom)?Describe this malfunction.

Warranty certiﬁcate

Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made

These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other selfemployed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aﬀected by this guarantee. Our guarantee is free of charge to you.
The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectiﬁcation of said defects on the product or the replacement of the product, whichever we prefer.
Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts ﬁtted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts ﬁtted. This also applies if an on-site service is used.
To make a claim under the guarantee, please register the defective device at:
www.Einhell-Service.com . Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identiﬁcation will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.

Of course, we are also happy oﬀer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.

Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.

Declaration of conformity

We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowed Brook Rd, Upton, Worrall CH49 0AB, United Kingdom declare the conformity to UK standards and legislation was assessed for:

Impact Wrench (Pneumatic) TC-PW 610 Compact (Einhell)

UK legislation

Simple Pressure Vessels (Safety) Regulation
Electrical Equipment (Safety) Regulation
Radio Equipment Regulation
Personal Protective Equipment Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation
Noise Emission in the Environment by Equipment for use Outdoors Regulation
Electromagnetic Compatibility Regulation
Measuring Instruments Regulation
Pressure Equipment (Safety) Regulation

Noise: measured LWA = dB (A); guaranteed LWA = dB (A)

X Supply of Machinery (Safety) Regulation

Annex IV Notiﬁed Body

Reg. No.

Standards: BS 11148-6

Wirral, 2021.07.12

Tom Chambers, Managing Director Einhell UK Ltd.