KRAMER KT-107 Wall/Table Mount Touch Panel User Guide

KRAMER KT-107 Wall/Table Mount Touch Panel User Guide

Scan for full manual

KT-107 Quick Start Guide

This guide helps you install and use your KT-107 for the first time. Go to www.kramerav.com/downloads/KT-107 to download the latest user manual and check if firmware upgrades are available.

Step 1: Check what’s in the box

KT-107 Touch Panel
Tabletop mount
On-wall mount unit
1 Quick start guide
1 C-USB/Micro B cable
AC/DC adapter
Installation screws
Panel mount plate
1 right-angle OTG USB cable

Step 2: Get to know your KT-107

Step 3: Mounting the KT-107

Mounting on a table using one of the following options:

Portable Mount : place the tabletop mount on the table. Connected cables remain visible and the table remains intact.

Secure Mount : secure the tabletop mount to the table as follows:

1. Measure the exact location on the surface of the table where you want to install the KT-107.
2. Drill a hole in the table and optionally cut the cable pass-through opening according to the cut-out dimensions defined in the user manual.
3. Secure the tabletop mount to the table using the M5x60 secure screw.
4. Connect the Ethernet port to a PoE-enabled source. Optionally, you can connect the power adapter too (as backup).
5. Replace the appropriate cover and place the KT-107 over the tabletop mount (the Touch Panel is magnetically held in place), by first inserting the lower part of the Touch Panel then carefully laying the KT-107 in place.
6. Wait for the Home-page to load and then secure the KT-107 to the tabletop mount from the rear side (using 2 M2x4 screws, supplied with the unit).
7. Optionally, lock the tabletop mount with a Kensington locker (not supplied).

Mounting on the wall:
Before mounting KT-107 on a wall, install an in-wall junction box (recommended boxes are listed in the user manual)

1. Attach the on-wall mount unit to the installed junction box (top side up see indication arrows on unit). Connect Ethernet and/or power cables and optionally, insert the right-angle USB cable (supplied) for connecting to an adjacent external USB device.
2. Screw the 4 wall-mounting screws (supplied) through the screw openings. The various screw openings fit various types of wall junction boxes.
3. On the rear side of the KT-107, remove the screw cover and the cover (by slightly pressing downwards and then pulling out) and set aside.
4. Attach the panel mount plate to the rear side of the KT-107 (using 4 M2x4 screws, supplied).
5. Connect the flat cable from the on-wall mount (attached to the in wall junction box) to the connector on the rear of KT-107.
6. Hang the KT-107 on the wall by sliding the tabs on the attached panel mount plate over the grooves on the on-wall mount unit.

For optimum range and performance use the recommended Kramer cables available at www.kramerav.com/product/KT-107.

• Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.

Step 4: Connect the power

Connect the power cord to KT-107 and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution :

• For products with relay terminals and GPIO ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
• There are no operator serviceable parts inside the unit.

Warning :

• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.

Step 5: Customizing the KT-107 settings

The Settings page is accessible from the Home-page and enables customizing the KT-107 settings:

To modify date and time settings :

1. In the Home-page, click Settings.
2. Scroll down to the System area and click Date & time.
3. Enable Automatic date & time to derive the date and time from the Network. When disabled, enter the date and time manually.
4. Select the time format.

To configure the Boot Start App :

1. In the Home page click Settings.
2. Click Control.
3. Click Select Boot Start App and select one of the available Apps (Kramer Control or K-Touch) to appear upon startup or select None.

To modify display settings :

1. In the Home-page, click Settings.
2. Select Display.
3. Set the following (as required):
   • Brightness : brightness level, adaptive brightness
   • Status Bar : Show/hide lower and/or top status bar
   • Auto Sleep : Sleep timeout.

To modify Control button settings :

1. In the Home-page, click Settings.
2. Select Control.
3. Enable or disable the Control button (Kramer Logo touch),.
4. Set Control button password protected to be enabled/disabled.

To change the password of the control button :

1. In the Home-page, click Settings.
2. Select Control.
3. Click Change password (default: Kramer).
4. Follow the instructions in the Password Set window.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.

Operation of the device is subject to the following conditions:

• This device may not cause harmful interference
• This device must accept any interference received, including interference that may cause undesired operation

Recommendations for safe exposure to non-ionizing radiation: Only use the device at least 20 centimeters away from your body.

Technical Specifications:

www.kramerav.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>