impact GALE-50 Studio Fan Instructions
- August 10, 2024
- Impact
Table of Contents
impact GALE-50 Studio Fan
Specifications:
- Power: 5 A
- Mount: 5/8 in.
Product Usage Instructions
Attaching the Air Duct:
- Remove the duct screw from the main body of the fan.
- Align the air duct with the hole and insert the screw.
- Tighten the screw until secure.
Mounting the Fan:
- Loosen the mount’s locking knob. Then press and hold the release button and seat the receiver onto the 5/8-inch stud.
- Tighten the locking knob until secure.
Adjusting the Tilt:
- Support the body of the fan with one hand and loosen the tilt locking knob.
- Tilt the fan into position, and tighten the locking knob until secure.
Fan Operation:
Warning: Before turning on the unit, make sure the fan is securely
attached to the stand, turned off, and no objects are sticking in the air
inlet or outlet.
- Plug the power cord into a power socket.
- Rotate the fan speed control clockwise until you hear a click and the power indicator lights up green and the fan starts to run.
Note: The fan produces a loud noise during operation and it is not recommended for use with audio recordings.
Changing the Fuse:
- With the fan unplugged, loosen the fuse cover in the direction of the arrow.
- Replace the 5 A fuse, and tighten the cover until secure.
FAQ:
-
Q: What should I do if my fan is making unusual noises?
A: Check for any loose screws or objects stuck in the fan that might be causing the noise. If the issue persists, contact Impact Customer Service for assistance. -
Q: Can I use this fan for audio recordings?
A: It is not recommended to use this fan for audio recordings as it produces a loud noise during operation.
Introduction
Thank you for choosing Impact.
Impact’s Studio Fan creates movement in your photos with this simple to use
wind effect. Direct the fan on a subject’s hair to simulate a windy beach
setting or some leaves blowing on a fall afternoon. Mount the fan onto any
light stand with a 5/8-inch stud and use the tilt feature to lock in the ideal
angle. A single knob operates the power switch and variable speed control so
you can dial in
Precautions ⚠⚡
WARNING ⚠ Do not stick any objects into the air inlet or outlet.
- Please read and follow these instructions, and keep this manual in a safe place
- Keep this unit away from water liquids.
- Make sure the unit is powered off when plugging it into a power source.
- Use only the correct, recommended voltage.
- Handle the unit with care.
- Clean the unit with only a soft, dry cloth.
- Do not attempt to disassemble or repair the equipment—doing so will void the warranty, and Impact will not be responsible for any damage.
- Keep this unit away from children.
- Use only parts provided by the manufacturer.
- Make sure this item is intact and that there are no missing parts.
- All images are for illustrative purposes only.
Overview
- Duct screw
- Air duct
- Air outlet
- Air inlet
- Tilt locking knob
- Release button
- Mount locking knob
- Mount (Accepts 5/8-inch stud or baby pin)
- Power and fan speed
- Power indicator
- Fuse (5 A)
Specifications
Operation
Attaching the Air Duct
- Remove the duct screw from the main body of the fan.
- Align the air duct with the hole and insert the screw.
- Tighten the screw until secure.
Mounting the Fan
- Loosen the mount’s locking knob. Then press and hold the release button and seat the receiver onto the 5/8-inch stud.
- Tighten the locking knob until secure.
Adjusting the Tilt
- Support the body of the fan with one hand and loosen the tilt locking knob.
- Tilt the fan into position, and tighten the locking knob until secure.
Fan Operation
Warning ⚠ Before turning on the unit, make sure the fan is securely
attached to the stand, turned off, and no objects are sticking in the air
inlet or outlet.
- Plug the power cord into a power socket.
- Rotate the fan speed control clockwise until you hear a click and the power indicator lights up green and the fan starts to run.
Note: The fan produces a loud noise during operation and it is not recommended for use with audio recordings.
Changing the Fuse
- With the fan unplugged, loosen the fuse cover in the direction of the arrow.
- Replace the 5 A fuse, and tighten the cover until secure.
One-Year Limited Warranty
This Impact product is warranted to the original purchaser to be free from
defects in materials and workmanship under normal consumer use for a period of
one (1) year from the original purchase date or thirty (30) days after
replacement, whichever occurs later. The warranty provider’s responsibility
with respect to this limited warranty shall be limited solely to repair or
replacement, at the provider’s discretion, of any product that fails during
normal use of this product in its intended manner and in its intended
environment. Inoperability of the product or part(s) shall be determined by
the warranty provider. If the product has been discontinued, the warranty
provider reserves the right to replace it with a model of equivalent quality
and function.
This warranty does not cover damage or defect caused by misuse, neglect,
accident, alteration, abuse, improper installation or maintenance. EXCEPT AS
PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES
NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides
you To obtain warranty coverage, contact the Impact Customer Service
Department to obtain a return merchandise authorization (“RMA”) number, and
return the defective product to Impact along with the RMA number and proof of
purchase. Shipment of the defective product is at the purchaser’s own risk and
expense.
For more information or to arrange service, visit
www.impactstudiolighting.com or call
Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
Impact is a registered trademark of the Gradus Group.
© 2024 Gradus Group LLC. All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>