impact PCLK-120 Dual LED Light Kit Instructions
- June 6, 2024
- Impact
Table of Contents
impact PCLK-120 Dual LED Light Kit.
Introduction
Thank you for choosing Impact. The Impact Dual LED Panel Light Kit allows you to light a copy stand or tabletop surface so you can shoot small products and documents with optimal lighting. These lighting supports clamp onto 1.45-inch- thick surfaces and offer five-way adjustment so you can position the light at any angle. There are 96 LEDs in each panel, producing a bright and cool 5600 K daylight color temperature.
Precautions:
- Please read and follow the instructions, and keep this manual in a safe place.
- Keep this unit away from water and any flammable gases or liquids.
- Do not leave this unit in a closed vehicle under the sun or in other areas subject to very high temperatures.
- Make sure this product is intact and that there are no missing parts.
- Do not attempt to disassemble or repair the equipment. There are high-voltage components inside the unit. Failure to observe this precaution could result in electric shock or product malfunction. This will void the warranty, and Impact will not be responsible for any damage.
- Use caution when expanding and collapsing this product.
- Clean with only a soft, dry cloth.
- All images are for illustrative purposes only.
Overview
- LED panel
- Cold-shoe adapter
- Tilt locking knob
- Support locking knob
- Horizontal support
- Horizontal support adapter
- Vertical adjustment locking knob
- Cable tie
- On/off switch
- Power cable
- Pivot locking knob
- Table clamp
- Vertical support
- Clamp locking knob
Installation Hardware
- LED panel (×2)
- Horizontal support arm (×2)
- Table clamp (×2)
- Vertical support arm (×2)
Setup
Table Clamp / Light Assembly
Follow these instructions for both support arms.
-
Unscrew and remove the clamp’s pivot locking knob.
-
Align the vertical support with the clamp. Screw the pivot locking knob through the washer and into the clamp assembly. Tighten until secure.
-
Loosen the clamp locking knob, and fit the clamp onto the surface edge. Tighten until secure.
-
Slide the horizontal support’s adapter over the vertical support. Tighten the adapter’s locking knob until secure.
Caution: The LED support adapters ship with a loose support brake inside the adapter. Be careful not to lose the support brake when removing the packing paper from inside the adapter.
-
Loosen the LED’s support adapter, and slide it over the horizontal support. Tighten until secure.
-
Plug each of the LED panels into a power source, and press the power switch to On.
Lighting Adjustments
Specifications
One-Year Limited Warranty
This Impact product is warranted to the original purchaser to be free from
defects in materials and workmanship under normal consumer use for a period of
one (1) year from the original purchase date or thirty (30) days after
replacement, whichever occurs later. The warranty provider’s responsibility
with respect to this limited warranty shall be limited solely to repair or
replacement, at the provider’s discretion, of any product that fails during
normal use of this product in its intended manner and in its intended
environment. Inoperability of the product or part(s) shall be determined by
the warranty provider. If the product has been discontinued, the warranty
provider reserves the right to replace it with a model of equivalent quality
and function.
This warranty does not cover damage or defect caused by misuse, neglect,
accident, alteration, abuse, improper installation or maintenance.
EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state. To obtain warranty coverage, contact the Impact Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Impact along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense.
For more information or to arrange service, visit www.impactstudiolighting.com or call Customer Service at 212-594-2353. Product warranty provided by the Gradus Group. www.gradusgroup.com Impact is a registered trademark of the Gradus Group. © 2021 Gradus Group LLC. All Rights Reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>