iPE Mclaren GT Exhaust System Instruction Manual
- June 3, 2024
- iPE
Table of Contents
iPE Mclaren GT Exhaust System Instruction Manual
Before Installation
Welcome to iPE Exhaust.
Thank you for choosing iPE Exhaust. Please carefully read and follow the
installation instructions below before proceeding with the installation.
Improper installation may result in a voided warranty.
By reading this installation guide and installing the exhaust system, you have
agreed to the terms and conditions stated in this manual. Please contact
support@ipeofficial.com for any further questions.
Installation Instructions for iPE Exhaust System*
– Please make sure the car is lifted properly. Failure to do so may cause
vehicle damage and personal injury including death. Please make sure the car
is lifted onto the proper lifting point.
– Exhaust systems can create extremely high temperatures. Prior to installing
your iPE exhaust system, please allow your car engine to cool down or wear
proper protective wear in order to prevent inju ries during installation
process.
– Please be careful, do not strip or break nuts and bolts during removal and
installation. Please tighten the bolts to the correct specifications in order
to prevent mechanical issues.
– With iPE Valvetronic exhaust systems, we recommend 60% throttle opening for
valve actuation , in order to prevent excess resonance with exhaust sound.
– Please note, It is normal for white smoke to be visible on the first start.
The smoke will dissipate after the exhaust reaches working temperature.
– For personal safety, please do not stand directly in front of the exhaust on
first start. As it is a new exhaust system, the muffler is not yet active.
There may be some manufacturing debris that will exit the exhaust system,
which may cause injury.
– Please note, iPE exhaust system requires a break-in period, the exhaust
sound and tone may change after driving approximately 300 miles (500 Km) after
installation.
Product Overlook
Down pipe
]
Stock System Removal
Seter 1 Remove the trim panel above the engine compartment.
– Please make sure the vehicle is parked properly onto the ramp, then raise it
up. While adjusting the height of the ramps, make sure it is cleared from
everything around it including people. To ensure safety. When removing the
screws, please place them in the correct order to avoid confusion during the
re-installation process
Step 2 Remove both rear wheels and inner wheel liners.
Step 3 Remove both rearfender liners and under tray.
Step 3 Remove both rearfender liners and under tray.
Stock System Removal
Step 4 Remove both intake manifolds.
Step 5 Remove the muffler cover.
Step 6 Remove the muffler and the front pipe clamps.
Stock System Removal
Step 7 Unplug the original electronic valve motor, then remove the muffler hanger mounts.
Step 8 Remove the clamps & lifting lug screws located at the end of the catalyst section.
Step 9 Remove the flare ring located at the inlet of the catalyst section.
Step 10 OEM exhaust system removal completed.
– Place the screws neatly in order, to avoid confusion during the re- installation process.
Installation
Step 1 Install the catalyst segment into position, flared exhaust pipe adapter and the rear lifting lug screws. Then install the 02 sensors and secure the muffler.
Step 2 Install the muffler into position, hanger mounts and tighten the clamps in sequence.Then connect and plug in the electric valve motors.
Step 3 Tighten the screws on the catalyst segment. Adjust the exhaust tips into position.
Return & Warranty
-
Product Warranty Period iPE provides limited warranty services for one year starting from the shipping date. After verifying that the failure occurred within the warranty period by iPE No inspection, parts, maintenance or other costs will be charged and of these costs will be incurred by iPE. Product warranties are nontransferable.
-
Warranty Policy:iPE’swarrantyseryices follows the standard operating procedure (SOP): Repair Replace Refund. The principlesof this procedure are as follow:
Repair:During the warranty period and under normal usage, iPE is responsible for free repairs if the problem is due to product quality issues.
Replacement During the warranty period and under normal usage, if the product quality issue arises and is unable to be solved by repairing, iPE is responsible for the free replacement.
Refund:lf the replacement of a new product does not resolve the issue and it is the prod uct’s q uality fault that causes the product to be unable to be repaired and used, please notify iPEwith in 7 days and iPE will give a full refund including shippingcosts. -
Product quality problems which are not included in the warranty includes: Consumables Under prolonged use, damaged flanges/screws/flange gaskets/springs/diaphragms/several strips/aluminum adapters… or slight rusting or discoloration of the product is common and natural.
The heat protector (heat wrap or heat shield) is a consumableand has a limited life span. Due to difference in personal usage or frequent disassembly, damage caused by wear and tear is common.
The tips and oxidized blue/purple colors are decorative parts. Before installation, please make sure that the appearance meets the requirements.Once installed and used, the return or exchange of the appearance will not be accepted. Please note that the decorative products will be affected by extreme environments.Therefore, there may be slightdiscoloration after prolonged use. In order to extend the I ifespan of the tips, DO NOT wash with corrosive chemicals.
A friendly reminder, whether it is a 200 cell catalyst or a catalyst-delete pipeRE products are designed for motorsport and race track use only. By deleting the catalytic converters or modifying certain parts of the exhaust system, the chances of triggering theCEL ‘Check Engine Light’ and ‘OPF/GPF (Otto Particulate Filter/ Gasoline Particle Filter)’ warning signal are high in certain car models. Please note, our warranty DOES NOT cover this or any software incompatibilities.
Read More About This Manual & Download PDF:
References
- iPE Valvetronic Exhaust System and Magnesium Wheels – iPE Official
- iPE Valvetronic Exhaust System and Magnesium Wheels – iPE Official
- iPE - Performance Redefined (@ipeofficial_) • Instagram photos and videos
- iPE - Performance Redefined (@ipeofficial_) | TikTok
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>