GOOD WAY NDW6000Z1 Wireless Display 1 Pair Dongle Instruction Manual

GOOD WAY NDW6000Z1 Wireless Display 1 Pair Dongle

Specifications

• Model: NDW6000Z1
• Type: Wireless Display 1 Pair Dongle (TX & RX)
• TX Dongle (NDW6010Z1):
  • USB-C with DP Alt Mode
  • Reset Key
  • Pair Button
• RX Dongle (NDW6020Z1):
  • HDMI Connection
  • Reset Button
  • USB-A 5V Power Supply

Product Usage Instructions

Pairing Process
Initiate the RX Dongle

1. Confirm the RX Device of NDW6000Z1.
2. Connect the USB-A side to the power source.
3. After booting, enter the main interface.
4. Press and hold the button on RX to display the pairing prompt.
5. Confirm that the version number, SSID display, and interface version are normal.

Press the Pair Button on the TX Dongle to Pair

1. Confirm the TX Device of NDW6000Z1 and connect to the device.
2. Press and hold the Pair button on the TX for about 5 seconds until the light stops.
3. About 1 second after the light stops, the light will flash faster.
4. Release the button to start pairing (TX/RX).
5. Confirm that Pairing OK is displayed and the screen is normal.
6. The pairing process is completed, mirroring the content of the device’s screen to the monitor.

Firmware Upgrade
Connect to the Setting Page

1. Press and hold the button on RX to display the pairing prompt. Confirm Ready to Pair is displayed.
2. Find the SSID displayed and connect to it in Wi-Fi settings.
3. Open the device’s web browser and enter IP address 192.168.203.1 into the settings page.

Connect Internet and Start Upgrading

1. Select the router to connect to on the setting page.
2. After configuring connectivity, the standby page will switch.
3. Click Upgrade for transmitter to start upgrading TX dongle’s firmware; click Upgrade to start upgrading RX dongle’s firmware.

Frequently Asked Questions (FAQ)
IC Warning
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

NDW6000Z1
Wireless Display 1 Pair Dongle
TX & RX
Pairing SOP Manual
Rev 1.0

ABOUT NDW6000Z1
NDW6010Z1

Wireless Display TX Dongle

The NDW6010Z1, with USB-C support and DP Alt mode, ensures seamless cross- platform connectivity with Windows, macOS, and ChromeOS on PCs or tablets.

NDW6020Z1
Wireless Display RX Dongle
The NDW6020Z1 includes an HDMI connection for TV and monitors compatibility.

PAIRING PROCESS

1. Initiate the RX Dongle
2. Confirm the “RX Device” of NDW6000Z1.
3. Connect the USB-A side to the power source.
4. After booting, enter the main interface.
5. Press and hold the button on RX to display the pairing prompt.
6. Confirm that the version number, SSID display and version number of the interface are normal and OK.
7. Press the Pair Button on the TX Dongle to Pair
8. Confirm the “TX Device” of NDW6000Z1 and connect to the device.
9. Press and hold the Pair button on the TX for about 5 seconds until the light stops. About 1 second after the light stops, the light will flash faster.
10. At this time, release the button to start pairing (TX/RX).
11. Confirm that “Pairing OK” is displayed, the screen is normal and OK.
12.  The pairing process is completed, mirroring the content of the device’s screen to the monitor.

FIRMWARE UPGRADE

1. Connect to the Setting Page

2. Press and hold the button on RX to display the pairing prompt. Confirm that “Ready to Pair” is displayed.

3. Find the SSID displayed. Open the Wi-Fi settings on the device, locate this SSID in the Wi-Fi list, and connect to it
   

4. When the connectivity is completed, open the device’s web browser and enter the IP address “192.168.203.1” into the settings page.

5. Connect Internet and Start Upgrading

6. When entering the setting page, select the router you want to connect to.

7. After configuring and establishing connectivity, the NDW6000Z1’s standby page will switch as follows.

8. Return to the setting page and click “Upgrade for transmitter” to start upgrading the TX dongle’s firmware; click “Upgrade” to start upgrading the RX dongle’s firmware.

FCC Warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modificaons not expressly approved by the party responsible for compliance could void the authority to operate the equipment.
This device and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter.
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Both the cradle and the scanner should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Proper use of this device ensures that exposure to RF energy is minimized and within the FCC guidelines.

IC Warning :
IC Radiation Exposure Statement:

mobile device
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.

portable device (SAR)
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions to satisfy RF exposure compliance. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>