KAIDI KDDYM002A, KDHM003A Power Motion Solution Instruction Manual

KAIDI KDDYM002A, KDHM003A Power Motion Solution

INSTRUCTION MANUAL

1. Power Motion Solution

2. Power Motion Solution

2. Power Motion Solution

3. PAIRING / UNPAIRING METHOD

COMMENT

1. Manual controller 1 and manual controller 2 have the sarne method of pairing, unpairing and restoring factory Settings;

2. After the pairing of manual controller 1 is completed, it enters the pairing state again, and pairs manual controller 2.
3. When only one hand controller is paired, only the functions on the hand controller are performed.
4. Aftcer che pairing is successful, the contcrol box is powered off and re- powered, the original pair will not be cleared, and che paired manual controller can still be used;
5. At the same tcime, only one manual controller can work, and aftcer the manual contcroller ls hibernation, the other manual controller can work, except the flashlight function;
6. Push rod {Hl) and {HR), when the push rod rises to the maximum stroke, the error before the two push rods is controlled within 2mm;
7. A control box supports a maximum of two controllers for pairing, when there is a third controller for pairing, the first cont roller pairing informat ion will be squeezed out, and so on;
8. Restore factory Settcings: When manual l is used to restore factory Sec tings, the head push rod and leg push rod corresponding to manual l retract to che end and stop, the pairing of manual l will not be cleared, the memory position of manual 1 is cleared, and the same is true for manual 2· ‘

4. matters need attention

1 . Before use, please be sure to correctly connect according to the system connection diagram, and then s,vitch on the main power supply;
2. Children, tl1e elderly and tl1e disabled, please use tmder supervision;
3. Do not insert or remove any cable \Vhen the power is on. This may cause operation failure. In this case, disconnect tlle n1ain power supply and reconnect it in about 30 seconds.
4. Before tL?e for die first time, the ,vireless manual controller should be paired \Vith the control box. For specific metllod?, see Manual pairing/unpairing method;
5. Please replace tl1e manual battery in tin1e. Take out tl1e battery if it is not used for a long tin1e.

FCC Warning for control box

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.

FCC Warning for handset

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interf erence received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if no t installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipmen t and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement.

Frequently Asked Questions (FAQ)

Q: How many memory positions can each memory key remember?

A: Each memory key can remember 1 group of positions.

Q: What should I do if the memory location is not cleared afterpower-on?

A: If the memory location is not cleared after power-on, try performing the memory function again. If the issue persists, contact customer support for assistance.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>