KAIDI ELECTRICAL KDDY109B Highly Functional Upholstery Instruction Manual

KAIDI ELECTRICAL KDDY109B Highly Functional Upholstery

Product Information

The KDDY109B + KDH243B is one control two control system that provides various functions. The system includes a hand control device, control box, power supply box, push rods, and a lamp with a vibrating motor. The control box has an input voltage range of AC 110-240V 50/60Hz and a rated output of 29V DC/ 5A. The manual controller operates on a 4.5V input voltage and has 14 keys for different functions.

Product Usage Instructions

To use the hand control device, follow these steps:

1. Preset Position:
   • Press K1 to stop the push rod at a fixed position (Leisure mode).
   • Press K2 to stop the push rod at a fixed position (Incline tilt mode).
   • Press K5 to stop the push rod at a fixed position (Zero gravity mode).
   • Press K6 to prevent the putter from moving.
   • Press K10 to stop the push rod at a fixed position (Anti-Snore mode).
2. Memory Function:
   • Hold down 6+1/6+2/6+5/6+10 simultaneously to modify the position memory.
   • After the backlight flashes for 3 seconds, the control box will remember the current position of the push rod.
   • Press any of the memory keys (K1, K2, K10, or K5) again, and the push rod will run to the corresponding memory position.
3. Push Bar 1 (Head Bar H):
   • Press K3 to extend the push rod. Release to stop.
   • Press K4 to retract the push rod. Release to stop.
4. Putter 2 (Leg Putter F):
   • Press K7 to extend the push rod. Release to stop.
   • Press K8 to retract the push rod. Release to stop.
5. Putt 1 and Putt 2 (Head and Leg):
   • Short press K9 to activate both putt 1 and putt 2 simultaneously.
   • Long press K9 and pull back after 3 seconds to deactivate both putt 1 and putt 2 simultaneously.
   • During the operation of the push rod, pressing any key will stop the push rod, except for Flat (K9) and Frogram (K6).
6. Vibration Mode:
   • Short press K14 to switch between different vibration modes.
   • Mode 1: Intermittent vibration with a slower frequency and intensity.
   • Mode 2: Intermittent vibration with a faster frequency and intensity.

System connection diagram

Product list

The serial number| Name (code name)| Model and Specificatio

n

| Num ber| note
---|---|---|---|---
1| Hand control

device

| KDH243| 1|
2| Control box| KDDY109| 1|
3| Power         supply

box

| KDDY01B| 1|
4| Push Rod 1 (H)| KDYJT014| 1|
5| Push Rod 2 (F)| KDYJT014| 1|
6| Lamp with| DY056| 1|
7| Vibrating motor| ZYD060| 2|

Performance Parameters

1. Control box performance parameters:****
   Input voltage| AC 110‐240V        50/60Hz
   ---|---
   Rated output (single

channel)

| 29V DC/ 5A (10% work system, maximum 2 minutes of continuous

work and 18 minutes of stop)

2. Manual controller performance parameters:****
   Input voltage| 4.5V
   ---|---
   Number of keys| 14

Outline of KDDY109B

Outline of H243B

Manual controller key function description

Function of the hand control device

position (Leisure mode) stop (head push rod travel: 42mm, leg push rod travel: 43mm).

2.  Press K2 gently and stop the push rod running to a fixed position (Incline tilt mode) (head push rod travel: 48mm, leg push rod travel: 32mm)

3.  Press K5 gently and stop the push rod running to a fixed position (zero gravity mode) (head push rod travel: 23mm, leg push rod travel: 37mm)

4, K6 touch press, the putter does not move.

5. K10 gently presses the push rod to a fixed position (Anti- Snore mode) and stops (head push rod stroke: 18mm, leg push

rod stroke: 0mm).

| 1、 Press any key to stop the push rod during operation;

2、 Perform the head putt first, then the leg putt

2| Place of memory| Press and hold 6+1/6+2/6+5/6+10 at the

same time. After the backlight

| 1、 The position can be modified   by the

customer according to

 |  | flashes for 3

seconds, the control box will remember the current position of the push

rod; At the same time, the buzzer buzzes once and the backlight is off. Press K1, K2, K10 or K5 again, and the push rod will run to the corresponding memory position;

| the itinerary after delivery; Hold down 6+1/6+2/6+5/6+10

for 3S to remember the current position (overwriting the previous position); At the same time, the control box buzzes once and the backlight flashes three times.

2、 Press any key to stop the push rod

during operation;

---|---|---|---
3| Push bar 1 (head bar H) lift| Press K3, push rod out, release will stop;

Press K4, push rod

retract, release will stop;

|
4| Putter 2 (leg putter F) lift| Press K7, push rod out, release will stop;

Press K8, push rod

retract, release will stop;

|
5| Putt 1 and putt

2 (head

and leg) fall together

| 1.  Long press K9 and pull back putter 1 and putter 2 at the same time after 3S;

2.  During the operation of the push rod, you can release the key (Note:

press any key and the push

| ****

1.    Short press is invalid

2.  During the operation of the push rod, press any key to stop the push rod, except Flat(K9) and Frogram (K6).

 |  | rod will stop, except Flat

(9) and Frogram (6).

|
---|---|---|---
6| Vibration mode| 1, short press K14, each| Mode 1: intermittent
 | switching and| vibration mode switch| vibration with a slower
 | vibration| starts from 1,123 cycle in| frequency;
 | intensity| turn;(Note: The| Mode 2: intermittent
 | selection| corresponding indicator| vibration with higher
 |  | light is highlighted)| frequency;
 |  | 2, long press K14, vibration| Mode 3: intermittent
 |  | mode automatically switch| vibration   with   the
 |  | (1S| fastest frequency;
 |  | at each interval), release| The three modes are
 |  | will stop, to stay in the| switched sequentially;
 |  | current gear vibration mode| If the
 |  | operation;| change button is not
 |  |  | operated within 15
 |  |  | minutes, the vibrating
 |  |  | motor will
 |  |  | automatically shut down
 |  |  | (select the motor
 |  |  | strength for the last
 |  |  | time and start to
 |  |  | calculate the time).
7|  | 3、 Short press K12,| The vibration motor can
 |  | vibration motor enhancement| be opened by the rise
 |  | (intensity| button of the vibration
 |  | is divided into four| motor (12) or by
 |  | gears), each time press| pressing the vibration
 |  | gradually strengthen.| mode (14) (Note: the
 |  | 4、 Short press K13, the vibration motor weakens (the strength is divided into four gears), and gradually decreases with each press, and the motor

stops with the fourth press. 5、 Short press K11 to

stop the vibrating motor.

| intensity of the vibration motor is in gear 3 at this time).
---|---|---|---
8| Lamp with| K15 Gently press (the button on the back of the hand controller), and the light belt will turn on. Press it again, and the

light belt will turn off.

|
9| pairing| Method 1: Long press the pairing button of the control box for 3 seconds to enter the pairing state;

Press the hand controller K3 and K7 within 15 seconds, hold

for 3 seconds, the control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes for 3 times, the pairing is

successful;

|
 |  | Method 2: Power on the control box again after 5 seconds of power failure, and the control box enters the pairing state; Press the hand controller K3 and K5 within 15 seconds, hold for

3 seconds, the control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes three times, the pairing is

successful;

|
---|---|---|---
10| Clearing matches| Method 1: Long press the pairing button of the control box for 3 seconds to enter the pairing state; Press the hand controller K4 and K8 within 15 seconds and hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes for 3 times. The pairing is

successful.

|
Method 2: Power on the|
 |  | control box again after 5 seconds of power failure, and the control box enters the pairing state; Press the hand controller K4 and K8 within 15 seconds and

hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the

hand controller flashes

for 3 times. The pairing is successful.

|
---|---|---|---
11| factory data reset| Method 1: Long press the pairing button of the control box for 3 seconds to enter the pairing state; Press the hand controller K3 and K8 within 15 seconds and hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes

quickly for 3 times.

|
Method 2: Power on the

control box again after 5

|
 |  | seconds of power failure, and the control box enters the pairing state; Press the hand controller K3 and K8 within 15 seconds and hold for 3 seconds. The control box buzzes once, the pairing button stops blinking, and the background light of the hand controller flashes

quickly for 3 times.

|
---|---|---|---
12| One control two| When the manual controller is paired with the control box A, it can be paired with the control box B, so

that one controller can

control the action of the control box at the same time

|

Precautions

1. Before use, please be sure to correctly connect according to the system connection diagram, and then switch on the main power supply;
2. Children, the elderly, and the disabled, please use under supervision;
3. Do not plug or remove any connection line when the power supply is switched on, which may cause operation function failure. In this case, you can cut off the main power supply and reconnect it after about 30 seconds.
4. Before the first use, the wireless hand controller should be paired with the control box. See Step 9 for the specific method;
5. The first use needs to be reset, to ensure that the memory position is accurate, the specific method to operate K9; 6, the control box can be paired with two hand controllers, if paired with the third, the first will be cleared. 7. Please replace the battery of the manual controller in time. If it is not used for a long time, the battery should be taken out.

Warning

This device complies with part  15  of the  FCC  Rules.  Operation  is subject  to  the  following  two conditions:

1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>