KICHLER Everly 1 Light Natural Brass Pendant Ceiling Light Instruction Manual

KICHLER Everly 1 Light Natural Brass Pendant Ceiling Light

FAQ

• Q: Can I use LED bulbs with this fixture?
  • A: Yes, you can use LED bulbs as long as they are compatible with the fixture’s socket type.
• Q: How do I adjust the position of the mounting strap?
  • A: The mounting strap can be adjusted by loosening the mounting screws and repositioning it before tightening them back securely.
• Q: What should I do if the glass shade breaks?
  • A: If the glass shade breaks, carefully remove any remaining glass, dispose of it properly, and contact customer service for a replacement.

PARTS LIST

• [A] Outlet Box (Not Supplied)
• [B] Strap Mounting Screw (2)
• [C] Mounting Strap
• [D] Mounting Screw (2)
• [E] Canopy
• [F] Lock Washer (2)
• [G] Knob (2)
• [H] Swivel (Attached to Canopy)
• [I] Stems (2-12”, 2-6” with Short Threaded Tubes [J] installed)
• [J] Short Threaded Tubes
• [K] Glass Shade Trim
• [L] Stem Coupling
• [M] Preinstalled Washer
• [N] Rubber Gasket
• [O] Steel Washer
• [P] Glass Shade (shape may be different than what is shown)
• [Q] Socket
• [R] Slotted Coupling

SAFETY INFORMATION

CAUTION:  RISK OF SHOCK:

• Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

1. This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

NOTE: Thread locking compound must be applied to threads as noted with (4) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc.

1. Lower glass shade trim[K] down over stem coupling[L], and seat on preinstalled washer[M].

2. Pass fixture wires from stem coupling through desired number of short threaded tubes[J] and stems[I]. Screw stems together using short threaded tubes.

   • Screw first stem into stem coupling.
   • NOTE: A minimum of one (1) 12-inch stem must be used when mounting fixture.

3. Pass fixture wires from last stem through end of swivel[H] and into canopy[E]. Thread the end of swivel into end of last stem. Note direction of swivel in accordance with ceiling.

4. Cut fixture wires a MINIMUM of 6 inches from the top edge of canopy.

5. Find the appropriate threaded holes on mounting strap[C] that align with hole distance in canopy. Assemble mounting screws[D] into threaded holes starting from the outlet box side.

6. Attach mounting strap to outlet box[A] using the supplied strap mounting screws[B]. Mounting strap can be adjusted to suit position of fixture.

7. Grounding instructions: (See Illus. a or b).

   • On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
   • On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
     If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

8. Make wire connections. Reference chart below for correct connections and wire accordingly.
   Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   Parallel cord (round & smooth)| Parallel cord (square & ridged)
   Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
   Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
   *Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|

9. Raise canopy to ceiling, carefully passing mounting screws through mounting screw holes in canopy.

   • NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and ceiling.

10. While holding canopy in place, use lock washers[F] and knobs[G] to secure canopy. Tighten to secure.

11. Carefully raise glass shade[P] up (over socket[Q] and slotted coupling[R]) to glass shade trim[K].

    • Carefully raise glass shade and glass shade trim together, above slotted coupling[R].
    • While holding glass shade and glass shade trim above slotted coupling, insert steel washer[O] into the slot in the slotted coupling.
    • While holding glass shade and glass shade trim above slotted coupling, slip rubber gasket[N] onto slotted coupling, and seat rubber gasket on top of steel washer.
    • Lower glass shade and glass shade trim, and seat glass shade on rubber gasket.
    • NOTE: When rubber gasket and steel washer are installed correctly, glass shade will seat between glass shade trim and rubber gasket.

12. Insert recommended bulb(s). (Not supplied).

Contact

• We’re here to help: 866-558-5706
• Hrs: M-F 9am to 5pm EST
• For warranty information please visit: kichler.com/warranty

© 2024 Kichler Lighting LLC. All rights reserved.

References

• Kichler® Warranty Information | Kichler Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>