SECO-LARM EV-Y2251-A2WQ 4 in 1 HD Turret Cameras Installation Guide
- August 5, 2024
- SECO-LARM
Table of Contents
SECO-LARM EV-Y2251-A2WQ 4 in 1 HD Turret Cameras
Specifications
- Model: EV-Y2251-A2WQ, EV-Y2251-AMWQ
- Housing Color: White
- Type: Fixed Turret Camera, Varifocal Turret Camera
- Formats: TVI (Default) / CVI / AHD / Analog (CVBS)
- CMOS: 1/2.7 2MP CMOS, 1/2.8 2MP CMOS
- Resolution (HD): 1920×1080
- 3DNR: Yes
- 2DNR: Yes
- D-WDR: Yes
- OSD (On-Screen Display): Yes
- Megapixels: 2MP
- Lens: 2.8mm ICR, 2.8~12 mm ICR
- Viewing angle: 39/16 (90mm)
- # of IR LEDs: 18 (SMT)
- IR Range: Up to 65ft (20m), Up to 115ft (35m)
- FPS: PAL:25FPS, NTSC:20FPS
- F Stop: F1.6
- Minimum IR On illumination IR Off: 0Lux, 0.05Lux, 0.02Lux
- S/N Ratio: 35dB
- Shutter control: Auto
- Gain control: Auto
- Operating voltage: 12VDC
- Current IR On draw: 320mA, IR Off: 292mA, 80mA
- IP rating: IP66
- Operating temperature: 16.72-oz (474g), 1-lb, 12-oz (800g)
Product Usage Instructions
Before Starting
- Use the camera within the given temperature and voltage limits.
- Do not point the camera at the sun to avoid damage from heat.
- Avoid strong vibrations.
- Avoid mounting the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
Installation
- Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted.
- Loosen the outer case ring and remove the case from the base.
Note: The camera ball is NOT attached to the case or the base. It sits loose inside the case, so be very careful when removing the case from the base. Do not drop the camera ball.
- Mount the base to the wall using the three included mounting screws. Use screw anchors for walls like drywall or brick.
- Run the camera’s BNC and power connectors through the camera base and connect to the video and power wires from the wall.
- Put the case over the camera ball and onto the base.
Holding the case loosely on the base, turn the camera ball to the desired direction. Use a small…
FAQ
-
Do I need to download additional manuals for full functionality?
No, for the full On-Screen Display manual, you can download it from the camera’s product page on www.seco-larm.com. -
I’m unsure about setting the Format via the DIP Switch, can you help?
To set the Format via the DIP Switch, follow these combinations: Format TVI (Default) Dip Switch 1: OFF Dip Switch 2: OFF
| Model | Lens | Resolution | Voltage | Style | Color |
|---|---|---|---|---|---|
| EV-Y2251- A2WQ | 2.8mm | 2MP | 12VDC | Turret | White |
| EV-Y2251- AMWQ | 2.8~12 mm |
- True Day/Night with ICR Module
- D-WDR (Digital Wide Dynamic Range)
- TVI, CVI, AHD, CVBS (Analog)
- Rugged, weatherproof (IP66) construction
- Heavy-duty vandal-resistant design
- Cables concealed in bracket to prevent tampering
For the full On-Screen Display manual, download from the camera’s product page on www.seco-larm.com.
Parts List
- 1x Turret camera
- 1x Mounting template
- 3x Mounting screws
- 1x Power Balun
- 3x Screw anchors
- 1x Manual
Specifications
Overview
EV-Y2251-AMWQ
IMPORTANT NOTES
- Do not cut DC jack or BNC connector jack as warranty will be voided.
- Do not open camera case, no serviceable parts.
Set Format via the DIP Switch
To set the Format via the DIP Switch, move the DIP Switches to the following combinations.
| Format | Dip Switch 1 | DIP Switch 2 |
|---|---|---|
| TVI (Default) | OFF | OFF |
| AHD | OFF | ON |
| CVBS (Analog) | ON | ON |
| CVI | ON | OFF |
Before Starting
- Use the camera within the given temperature and voltage limits.
- Do not point the camera at the sun. Heat could damage the camera, even when not in use
- Do not subject the camera to strong vibrations.
- Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals
Installation
-
Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera is to be mounted.
-
Loosen the outer case ring and remove the case from the base.
NOTE: The camera ball is NOT attached to the case or the base. It sits loose inside the case, so be very careful when removing the case from the base. Do not drop the camera ball. -
Mount the base to the wall using the three included mounting screws. If the wall is made of dry wall, brick, or similar material, it may be necessary to use the included screw anchors.
-
Run the camera’s BNC and power connectors through the camera base, and connect to the video and power wires that were run through the wall.
-
Put the case over the camera ball and onto the base
-
Holding the case loosely on the base, turn the camera ball to the desired direction. Use a small screwdriver to adjust the zoom and focus of the camera ball if needed, via the holes marked “ZOOM” and “FOCUS” on the top of the camera ball (EV-Y2251-AMWQ only).
NOTE: Before securing installation, make sure to check both the day and night images. Adjust the camera ball in such a way so that there are no objects blocking the camera’s view. -
Use the DIP Switches to adjust camera output format.
-
Once the ball is pointing in the desired direction, tighten the outer case ring to secure the camera in its position.
-
Do a final test of the video camera and monitor.
NOTE: For the full On-Screen Display manual, go to the camera’s product page at www.seco-larm.com.
Troubleshooting
The screen is black
- Check that the camera is powered up
- Check that the power supply’s polarity is correct
- Check that the monitor is powered up
- Check that the video cable connecting the camera to the monitor is connected properly
The image is foggy or washed out at night
- Check that there are no objects very close to the camera
- Check that there are no highly reflective objects in the scene
The screen image is dim
- Clean the lens using a soft, clean cloth
- Check that the light source is adequate
The screen image has poor contrast
- Adjust the monitor’s contrast knob
- Change the position of the camera
The screen image flickers
- Change the position of the camera, check cables and format setting
The screen image is distorted
- Change the position of the camera, check cables and format setting
The camera case is hot
- Check that the correct power supply is in use
IR LEDs do not turn on
- Check that the correct power supply is in use
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
- THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
- THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF
exposure requirements and void user’s authority to operate the device.
IMPORTANT: Users and installers of this product are responsible for
ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-
LARM will not be held responsible for the use of this product in violation of
any current laws or statutes.
IMPORTANT: Users and installers of this product are responsible for
ensuring that the installation and configuration of this product complies with
all national, state, and local laws and codes. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or
codes.
California Proposition 65 Warning: These products may contain chemicals
which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
WARRANTY: This SECO-LARM product is warranted against defects in material
and workmanship while used in normal service for three (3) years from the date
of sale to the original customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned,
transportation prepaid, to SECO-LARM. This Warranty is void if damage is
caused by or attributed to acts of God, physical or electrical misuse or
abuse, neglect, repair or alteration, improper or abnormal usage, or faulty
installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects
in material and workmanship. The sole obligation of SECO-LARM and the
purchaser’s exclusive remedy, shall be limited to the replacement or repair
only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any
special, collateral, incidental, or consequential personal or property damage
of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and
improvement. For that reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for
misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their
respective owners. Copyright © 2024 SECO LARM U.S.A., Inc. All rights
reserved.
SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: 949-261-2999 |
800-662-0800
Email: sales@seco-larm.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>