Jyrsin GR-8007 Gasoline Tiller Instruction Manual

: October 30, 2023
: Jyrsin

Table of Contents

Jyrsin GR-8007 Gasoline Tiller
Product Information
- Safety Instructions
- Clothing
Product Usage Instructions
Mounting
Troubleshooting
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Jyrsin GR-8007 Gasoline Tiller

Jyrsin GR-8007 Gasoline Tiller product

Product Information

The gasoline tiller is a machine used for soil cultivation in gardens, farms, and other outdoor areas. It comes with upper steer and cables, blades, lower steer, side guards, user manual, bolts, and nuts. The machine is equipped with a throttle handle, forward speed handle, and rear speed handle. The tiller is powered by an engine that requires oil and fuel to operate.

Safety Instructions

When operating the tiller, follow these safety instructions carefully. Read all of the operating instructions before starting the machine. Make sure you are capable of stopping the machine immediately and switching off the engine in the event of an emergency. All instructions for the handling and maintenance of your tiller are also for your own safety!

The tiller must not be used in any other way than described in the manual.
Use only genuine equipment and spare parts. If you use non-approved spare parts, there is increased risk and this is, therefore, not permissible. All liability is renounced in the event of an accident or other damage caused by the use of non-approved parts.
Before using the machine for the first time, the dealer or other knowledgeable person must instruct in its use.
When using the tiller you are responsible for any third party in the area where the machine is in operation. Never use the tiller in the presence of others, especially children or animals.
Do not allow minors to operate the tiller.
The tiller may only be lent to persons who are familiar with operating the machine. Always pass on the safety and operational instructions.
Only allow persons who are rested, healthy and fit to operate the machine. If the work is tiring, take a break in plenty of time. Do not operate the machine after drinking alcohol.
Do not remove or cover the controls which are mounted on the tiller at the factory, e.g. removing the clutch lever from the handlebar.
Remember to tighten all bolts and nuts before starting.
When the engine is running, do not pull the handle for forward speed and the handle for rear speed at the same time! This will damage the transmission. Always release one handle before the other is used.

“Beware of the rotating knives”
Working with the machine on a steep slope is dangerous! Only use the machine on areas where it can be handled safely.

Clothing

When working with the tiller, wear close-fitting work clothes, sturdy work gloves, hearing protection and boots with non-skid soles, and steel nose is compulsory.

Product Usage Instructions

Clean the area of all foreign items before use. Stone, glass, branches, etc. can damage the tiller.
Check that all bolts on the tiller are tightened.
Mount the lower steer using the accompanying bolts and nuts.
Mount the upper steer using the accompanying bolts and handwheels.
Mount the side guards using the accompanying bolts and nuts.
Mount the blades using the cotter bolts and pins. It is important that the edge of the blade turns forward.
Follow the user manual guide to fill the engine with oil and fuel.
Place the throttle handle on full throttle to start the machine. Follow the guide in the user manual to start.
Use the handle labeled with “forward speed” to move the tiller forwards. Use the handle labeled with “rear speed” to move the tiller backwards. If your back is against an obstacle, pay extra attention when reversing, for example a tree or a wall. Note: For different market demand, thismachine may not have reverse function.
Place the throttle handle on minimum throttle to stop the machine. Follow the guide in the user manual to stop.

The outer blades can be dismounted if the tiller is used between narrow rows of plants and crops. This reduces the tilling width.
The ground can be tilled in two directions, thus achieving optimum tilling.
When the engine is running, do not pull the handle for forward speed and the handle for rear speed at the same time! This will damage the transmission. Always release one handle before the other is used. Always wait until the blades have stopped rotating before another handle is activated.
It is important, that you do not try to hold back the tiller. It must be relaxing to use the machine.
Do not overload your tiller. Always drive carefully.
Adjusting the depth skid
The depth skid can be adjusting for tilling in three different depths. The deeper the depth skid sits in the soil, the deeper the tilling blades will work and the slower the machine will advance. The right cultivating depth will lighten your workload. The correct tilling depth depends on the soil, and we recommend you make several attempts to see how deep the depth skid should be so that you can work optimally in your soil.
To adjust the depth skid, pull it backwards and up till the preferred height is found. Place the depth skid vertically, and it will fall into a notch. The depth skid can be adjusted to various tilling depths. The deeper into the ground the depth skid goes, the deeper the tiller will work.
The right setting depends on the soil.
Adjusting the support wheels
The support wheels are mounted on the tiller. They can be adjusted to the required height by pulling the lock handle and moving the ring up or down.
The wheel ring can be used to stabilise the machine when tilling and also help to prevent the machine falling into soft soil.
Cleaning the tiller
The tiller should be cleaned after use. Use your garden hose and wash off soil and dirt. Clean the rotor shaft of any grass, etc. The chassis number should only be cleaned with a moist cloth otherwise it may be damaged. Avoid using a high pressure cleaner for cleaning.
Maintaining the gear box
The gear box on the tiller is lubricated at the factory. It is not necessary to renew the oil.
Engine
The engine is delivered without oil and fuel. Remember to fill the engine with engine oil before starting.
Follow the guidelines in the user manual for correct use and maintenance of the engine.
Storage
Follow the procedure below when the machine is to be unused for a long period. This will ensure the machine has a long service life.
Use your garden hose to wash off any soil and dirt. Clean the rotor shaft of any grass, etc. The chassis number should only be cleaned with a moist cloth otherwise it may be damaged. Avoid using a high pressure cleaner for cleaning. Clean the body with a damp cloth so all the surfaces are clean. The surface must be wiped with an oily cloth to prevent rust.
You should always store your machine in a dry, clean place.

Mounting

Contents of the package:
- a. Tiller with upper steer and cables.
- b. Blades
- c. Lower steer
- d. Side guards
- e. User manual and bolts
Mount lower steer using the accompanying bolts and nuts.
Mount upper steer using the accompanying bolts and handwheels.
Mount the side guards using the accompanying bolts and nuts.
Mount the blades using the cotter bolts and pins.
It is important that the edge of the blade turns forward.
Follow the user manual guide to fill the engine with oil and fuel .