XLR Security RG-EST310-V2 Ruijie Reyee Wireless Bridge Australian Stock User Manual

XLR Security RG-EST310-V2 Ruijie Reyee Wireless Bridge Australian Stock

USER MANUAL

Note
The device and software will be upgraded constantly. Please contact Ruijie technical support for details.

Parts List

Management software WSP-EST310 V2 has been installed on the device.

Networking

LED & PORT

1 . LED Description

a. System LED
Blinking Green: The device is being booted.
Solid Green: The device is working properly.

b. LAN LED
Off: No cable is connected.
Blinking Green: Link is up. The port is sending or receiving data.
Solid Green: Link is up. The port is not sending or receiving data.

c. Signal LED
Off: No signal is detected.
Blinking: The signal is weak.
Solid: The stronger the signal gets, the more LEDs light up.

2. 12V DC Power Port
Inner Diameter: 2.1 mm. Outer Diameter: 5.5mm.

3. LAN/PoE Port

4. Reset Button
CaVblidee Co oRnenceorcdteior nE nd

VIDEO RECORDER END

PoE Max Distance: 1 00m (CAT5/6ll Cable)

Mounting the Device Pole Mounting

1. Secure the mounting bracket to the pole by threading two clamps through the mounting bracket.
2. Install the device to the mounting bracket.

Wall Mounting

1. Secure the mounting bracket on the wall.
2. Install the device to the mounting bracket.

Bridging Management

The wireless bridges are used in pairs without extra configuration. If you want to manage the bridge or view data, both App management and Web management are available.

App Management (Recommended)

1. Scan the QR code on the manual or device to download Ruijie ReyeeApp.

2. Sign up an account and log in with it.
3. Navigate to Project>+in the upper right corner > Wireless Bridge to manage the device.

Web Management

Wireless Login (Recommended)

1. Connect to the 5G SSID of the bridge (Default: @Ruijie-bxxxx.
xxxx indicates the last four digits of the MAC address).
2. Open a browser window, enter http:/1192.168.120.1 into the address bar and press Enter.

Wired Login
1. Set the IP address on your computer.
IP Address: 10.44.77.100
Subnet Mask: 255.255.255.0
Gateway: 10.44.77.254

Figure 1-1

2. Open a browser window, enter http:/110.44.77.254 into the address bar and press Enter.

One-to-Many Settings

Select Master Bridge
Select any video recorder end as the master bridge and power on the device.

Select Slave Bridge
Select any other device ( either video recorder end or camera end) as the slave bridge and take the following steps to configure the slave bridge.

Configure Slave Bridge

1. Log into the Web management page.
2. Select Pair Again in the upper right corner.

VCR (AP) ti_ Pair Again ] Figure 2-1

3. Click Start.

4. Select a country or region from the dropdown list and click Next.

5. Select Camera (CPE) and click Next.

6. Click Scan and select an SSID from the dropdown list or enter an SSI D (Example: @Ruijie-wds-xxxx. xxxx indicates the last four digits of the MAC address).

7. Click Submit.

8. The Mode LED on the video recorder end is solid on and the Mode LED on the camera end blinks at 0.5 Hz.
9. If you want to add camera ends, please take the above steps again.

Notes
1 .Please make sure that there are no obstacles between both ends.
2. If there are obstacles, please make sure that the devices are installed 3 to 5 meters higher than the obstacles.
3. If the obstacles cannot be avoided, it is recommended to adopt the repeater solution to implement Back-to-Back WDS.
4. For data transmission over a super-long distance, it is recommended to adopt the repeater solution to reduce distance between each pairing devices and improve stability.
5. If the monitoring devices and peer ends are concentrated at one location, it is recommended to select one-to-many solution to reduce cost and improve efficiency.
6. Please make sure that the distance between both ends are over 2 meters.
7. The Mode LED on the video recorder end is solid on and the
Mode LED on the camera end blinks at 0.5 Hz.
8. The device may cause radio interference in living environment.
Please take measures to reduce interference.

Note:
This equipment is restricted to indoor operation in 5.15-5.25GHz for Hong Kong.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>