somfy SONESSE2 Ultra 30 Zigbee HP LI Installation Guide
- August 2, 2024
- somfy
Table of Contents
somfy SONESSE2 Ultra 30 Zigbee HP LI
Complete instruction guide available online on www.somfy.info
WAKE UP THE DRIVE
For initial unpackaging of drive, wake up the drive by briefly pressing the
motor head programming button or plugging in the charger.
START UP
To set the drive, download “TaHoma pro” application available on stores
DRIVE SETTING
Once the “TaHoma pro” application is downloaded, open the app and follow the
instructions to set the drive.
USE
This drive does not require any maintenance operation.
DRIVE RESETTING
This reset deletes all programmed control points, all end limit settings,
resets the favourite (my) position for the drive and leaves the current Zigbee
network.
INSTRUCTIONS TO BE RESPECTED
These instructions apply to all SONESSE2 ULTRA30 Zigbee HP LI drive, the different versions of which are available in the current catalogue.
FIELD OF APPLICATION
The Sonesse 30 drives are designed to motorise all types of:
- Interior vertical blinds which front rail moves solely by gravity with a mass less than 15 kg.
- Tiltable venetian blinds which bottom lath can be lifted at least by 4 cm when an upward force of 150 N is applied to the bottom lath positioned at 16 cm from the fully extended position.
LIABILITY
Please read these instructions carefully before installing and using the
drive. In addition to following the instructions given in this guide, the
instructions detailed in the attached Safety instructions document must also
be observed.
The drive must be installed by a motorization and home automation professional, according to instructions from Somfy and the regulations applicable in the country in which it is commissioned. It is prohibited to use the drive outside the field of application described above. Such use, and any failure to comply with the instructions given in this guide and in the attached Safety instructions document, absolves Somfy of any liability and invalidates the warranty.
The installer must inform its customers of the operating and maintenance conditions for the drive and must provide them with the instructions for use and maintenance, and the attached Safety instructions document, after installing the drive. Any After-Sales Service operation on the drive must be performed by a motorisation and home automation professional.
If in doubt when installing the drive, or to obtain additional information, contact a Somfy adviser or go to the website www.somfy.com
SAFETY INSTRUCTIONS FOR WIRING
- Cables which pass through a metal wall must be protected and isolated using a sheath or sleeve.
- Attach cables to prevent any contact with moving parts.
- If the drive is used outdoors, and if the power supply cable is a type H05-VVF cable, the cable should be installed in a UV-resistant duct, e.g. under a gland.
- Leave the drive power supply cable accessible: the product must be easily replaceable.
- Always make a loop in the power supply cable to prevent water entering the drive.
WARNING To ensure electrical safety, this Class Ill drive must be powered by a «SELV» voltage source (Safety Extra Low Voltage). The drive must be installed by a professionally qualified person (electrical specialist according to DIN VDE 1000-10) for drives and automations in the building services sector in accordance with the Somfy instructions and the applicable regulations in the country of commissioning.
Using this drive with any products which are not listed in the attached «Compatibility matrix» document shall also render invalid any Somfy warranty and release Somfy from any liability.
- For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.
- Improper using battery pack may cause overheat, fire, explosion, resulting in serious injury or death.
- Do not expose the drive or battery to excessive temperatures.
- There is a risk if terminals of the battery-operated drive or battery being short circuited by metal objects.
- Ensure battery is fully charged prior to installation on site.
- To increase the life of the battery, it is recommended to fully charge it every other year.
SPECIFIC INSTRUCTIONS FOR ASSEMBLY
SONESSEZ ULTRA30 Zigbee HP LI : interior diameter of the tube has to be ® 28.8 mm or greater.
Frequency bands and Maximum power used
2.4 GHz – 2.4835 GHz e.r.p. <63mW [USA, Australia, Canada] 2.4 GHz – 2.4835
GHz e.r.p. <10mW [Other countries]
Power supply
15V DC- 1A class 2 power supply SELV + LPS
Charging temperature
0 °C to 40 °C
FCC warning statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- End users must follow the specific operating instructions for satisfying RF exposure compliance.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and any part of your body.
FCC ID: DWNSON2830ZB241 ISED WARNING STATEMENTS
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator and any part of
your body. emot RSSs. Operation is subiect to the following two conditions
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device. ISED ID:
12049A-SON2830Z241
Apple and Apple logos are trademarks of Apple, Inc., registered in the U.S. and other countries. iPad® and iPhone® are registered trademarks of Apple, Inc. App Store is a service mark of Apple Inc.
Android is a trademark of Google LLC. https://developer.android.com/distribute/marketing-tools/brand-guidelines
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.