Yorkville NX Powered Loundspeakers Owner’s Manual

POWERED LOUDSPEAKERS
Owner’s Manual
NX8P, NX12P

IMPORTANT SAFETY INSTRUCTIONS

| This lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
---|---
| The DO NOT STACK symbol is intended to alert the user that the product shall not be vertically stacked because of the nature of the product.
| SEPARATE COLLECTION WEEE
CAUTION: RISK OF ELECTRIC SHOCK
DO NOT OPEN| | DO NOT PUSH OR PULL
---|---|---|---
| CAUTION: HOT SURFACE| | NOT TO BE SERVICED BY USERS
| The exclamation point within an equilatereal triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.| | CAUTION: OVERHEAD LOAD

FOLLOW ALL INSTRUCTIONS
Instructions pertaining to a risk of fire, electric shock, or injury to a person
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS DEVICE IS FOR INDOOR USE ONLY!
INSTALLED BATTERY PACKS SHALL NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE, FIRE OR THE LIKE.
Read Instructions: The Owner’s Manual should be read and understood before operation of your unit. Please, save these instructions for future reference and heed all warnings.
Cleaning: Clean only with dry cloth.
Packaging: Keep the box and packaging materials, in case the unit needs to be returned for service.
Warning: To reduce the risk or fire or electric shock, do not expose this apparatus to rain or moisture. Do not use this apparatus near water!
Warning: When using electric products, basic precautions should always be followed, including the following:

Power Sources
Your unit should be connected to a power source only of the voltage specified in the owners manual or as marked on the unit. This unit has a polarized plug. Do not use with an extension cord or receptacle unless the plug can be fully inserted. Precautions should be taken so that the grounding scheme on the unit is not defeated. An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective earthing connection.
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
Hazards
Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious personal injury and serious damage to the product. Use only with cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. Only use attachments/accessories specified by the manufacturer.
Equipment that is suspended overhead must use a secondary safeguard to prevent personal injury in the event the primary mounting mechanism fails. Safety eyebolts attached to the equipment and galvanized steel wire can be used together to implement a failsafe mounting thus ensuring the safety of the equipment and anyone positioned below the equipment.
Improper installation can result in bodily injury or death. If you are not qualified to attempt the installation get help from a professional structural rigger.
Note: Prolonged use of headphones at a high volume may cause health damage to your ears.
The apparatus should not be exposed to dripping or splashing water; no objects filled with liquids should be placed on the apparatus.
Te rminals marked with the “lightning bolt” are hazardous live; the external wiring connected to these terminals require installation by an instructed person or the use of ready made leads or cords.
Ensure that proper ventilation is provided around the appliance. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Power Cord
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. The AC supply cord should be routed so that it is unlikely that it will be damaged.
Protect the power cord from being walked on or pinched particularly at plugs. If the AC supply cord is damaged DO NOT OPERATE THE UNIT. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. The mains plug of the power supply cord shall remain readily operable.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Service
The unit should be serviced only by qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, requires battery pack replacement or has been dropped.
Disconnect power before servicing!

| The Lightning Flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons
---|---
| The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prongs are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING:

• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.
• To completely disconnect this apparatus from the ac mains, disconnect the power supply cord plug from the ac receptacle.
• The mains plug of the power supply cord or appliance coupler shall remain readily accessible.

CAUTION, TO PREVENT ELECTRIC SHOCK HAZARD, DO NOT CONNECT TO MAINS POWER SUPPLY WHILE GRILLE IS REMOVED.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with ISED Canada’s license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Introduction

Congratulations on your purchase of an NX Series active loudspeaker. If your live performances or DJ gigs require peak performance, the latest generation of our NX power loudspeakers were designed to deliver.
Some features of the Yorkville NX Series:![Yorkville NX Powered Loundspeakers

• Introducttion 1](https://manuals.plus/wp-content/uploads/2024/08/Yorkville- NX-Powered-Loundspeakers-Introducttion-1.jpg)

  • Dual purpose full-range and wedge monitor enclosure
  • Bluetooth™ connection for streaming audio to the system
  • Built-in 3-channel mixer with input settings for line and mic sources
  • Activity and Clip indicators on all channels with a Limit indicator on the Master channel
  • Main input/output for connecting two or more NX loudspeakers together as well as other applications
  • 48V phantom power available on channels 1 and 2
  • Selectable high-pass filters on channels 1 and 2
  • Selectable Sub high-pass filter for connecting with a subwoofer
  • Live, Club, and Monitor system modes which tailor the sound of the system for the intended application

Channel Features

1. Channels 1 and 2 – Mono

Channel 1 and 2 inputs are designed for mono signals, the combi-jacks allow either an XLR or 1/4-inch jack to be used. These channels are set up to handle both line level and  microphone level sources, with 48V phantom power present on the XLR inputs. To best optimize volume, input sensitivity and audio quality (for a given input type), use the channel’s input switch to select between “Line” or “Mic.” Each of these channels comes equipped with a switchable 90Hz high-pass filter (HPF), the pushbutton switch illuminates when active. This high-pass filter is often used when low-frequency content may not be desirable, such as with vocals and some instruments. Use the level control to adjust the level of the channel’s signal being sent to the Master. The Act/Clip led will illuminate green when a signal is being detected at the input and will illuminate red when clipping.
Note: The Act/Clip LED responds only to the strength of the input signal and is not affected by the channel’s level control.

2. Channel 3 – Stereo

The Channel 3 input has been designed for stereo input sources, connect using the 1/8-inch input jack and/or Bluetooth™. The left and right signals from the stereo source/s will be summed properly and the signal will be passed to the master section. The level control, as well as the Act/Clip indicator for this channel, behave in a similar fashion to channels 1 and 2.

Bluetooth™

These new Yorkville NX Series loudspeakers are capable of Bluetooth™ audio streaming from devices such as smart phones, tablets and laptops. Pairing your device with an NX Series loudspeaker is simple and gives you the freedom to play your music wirelessly.
Bluetooth™ Operation
When the NX Series cabinet is powered on, Bluetooth™ will be disabled by default. To enable it and connect to your device, simply tap the Bluetooth™ button. If a device was previously connected to the NX Series cabinet, it will attempt to automatically reconnect. Similarly, if a wireless stereo connection was previously established, both NX Series cabinets used will attempt to automatically re-establish the wireless stereo connection (in the same Primary or Secondary role they previously performed).

1. Pairing
   To pair your device to an NX Series cabinet, simply press the Bluetooth™ button down and hold for 4 seconds, then release the button.

2. Status
   The blue status indicator alerts let you know the current status of the Bluetooth™ connection as described in this chart:Mode| Linked| Link-Back| Standby| Pairing| Stereo Grouping| Grouped
   ---|---|---|---|---|---|---
   Standalone| ON| ON, blinks 1x every 2 seconds.| Flashes 1x every 2 seconds| Flashes 2x per second| N/A|
   Stereo Primary| N/A O| ON, blinks 1x every 2 seconds.| Flashes 2x every 2 seconds| Flashes 3x per second| Double flash O| ON
   Stereo Secondary| N/A N| N/A| N/A N| N/A N| Double flash S| Slow flash

3. Level Control
   The streamed music’s volume can be changed via the connected Bluetooth™ device as well as the Channel 3 Level control on the NX Series cabinet. For optimal audio quality, try to keep the volume control of the Bluetooth™ device above 50% and use the Channel 3 level control on the NX Series cabinet to achieve the desired output volume.

4. Stereo Mode
   The NX Series supports wireless stereo playback between two NX Series cabinets, for an enhanced listening experience. One cabinet will act as the Primary unit, while the other acts as a Secondary unit.
   The Primary unit will play the left audio channel of streamed music, and also maintain the Bluetooth™ connection with your device, while the Secondary unit will play the right audio channel. Your device only connects to the Primary unit, not the Secondary.
   To enable Stereo Mode, simply double tap the Bluetooth™ button on the NX Series cabinet that should act as the Primary unit (left channel), then double tap the Bluetooth™ button on the other NX Series cabinet (right channel). The order matters, as the first unit double tapped will become the Primary unit (left channel). Both NX Series cabinets will automatically attempt to re- establish the Stereo Mode connection the next time they are powered on and enabled, with the same Primary and Secondary roles previously used.
   You can still pair new devices to an NX Series Primary cabinet if it is in Stereo Mode. Pairing a device to an NX Series cabinet that is in Secondary mode will end the stereo wireless connection.

5. Button Operation
   Single Tap – Enables Bluetooth™
   Double Tap – Enter Stereo Mode
   Press and Hold (4 seconds) – Enter Pairing Mode
   Press and Hold (8 seconds) – Disables Bluetooth™

6. Range
   The NX’s Bluetooth™ operating range is rated for 10 meters (33 feet) line of sight. The quality of the link can be affected by an excess of traffic in the 2.4 GHz bandwidth or structures between the Bluetooth™ unit and the streaming device.
   
   Note: When connected with Bluetooth™, ALL audio is streamed from your device. If you don’t want your streaming music to be interrupted, turn off ‘notifications’ on your device.

Master Section

1. Master Control
   The Master Control is used to set the overall level of the NX system. Like with the mixer channels, the master section contains an LED to show when activity is detected at the input of the channel (green), and if there is clipping detected (red). In addition to these two indicators, the master LED will glow orange if the system is in limiting. For optimal performance, the level of the system should be set such that the Activity/Limit/Clip indicator is primarily green during use. Occasional indications of limiting (orange) is okay, but the unit should not be operated into clipping.
   Note: When two systems are linked together, the Master Control only affects the level of the unit on which it is located.

2. w/Sub Switch
   The sub switch provides a system-level 100Hz high-pass filter that should be enabled when the system is linked with an external subwoofer. The switch will illuminate when active.
   Note: While the NX Series loudspeakers can use Bluetooth™ to connect to each other, the use of a subwoofer requires a cable attached from the MAIN OUT and the w/SUB pushbutton must be enabled.

3. Performance Modes
   The NX Series contains 3 system performance modes which alter the unit’s EQ and dynamics to best suit its intended use and application. For music playback, Club mode should be selected. For live performance, Live mode should be selected.
   When used as a wedge monitor, the Mon mode should be selected.

Main Input/Output Section

In situations where additional bass or input channels are needed, the Link jacks can be used to connect multiple NX systems and/or a subwoofer.
Main Input and Output Jacks
The Main Input should be used with line-level signals, goes directly to the master section, and is only affected by controls within the master section. The main output provides a full-range, line-level output signal, which contains a sum of all signals from the mixer section, as well as any signal present on the main input.

Specifications

Compression Driver
Channel 1 Input| XLR / ¼-inch Combi-jack| X LR / ¼-inch Combi-jack
Channel 1 Controls| Level, Input Type, High-Pass| Level, Input Type, High-Pass
Channel 2 Input| XLR / ¼-inch Combi-jack| X LR / ¼-inch Combi-jack
Channel 2 Controls| Level, Input Type, High-Pass| Level, Input Type, High-Pass
Channel 3 Input| 1/8-inch TRS Stereo Jack, Bluetooth™| 1 /8-inch TRS Stereo Jack, Bluetooth™
Channel 3 Controls| Level| Level
Master Controls| Master Level, With Sub, Mode| Master Level, With Sub, Mode
Main In/Out (type / configuration)| XLR (Male and Female), Buffered Main Output| XLR (Male and Female), Buffered Main Output
LED Indicators| Channel Activity/Clip, Channel Input Type, Channel High-Pass
Filter, Master Activity/Limit/Clip, With Sub, Master Mode,
Bluetooth™ Status| Channel Activity/Clip, Channel Input Type, Channel High- Pass
Filter, Master Activity/Limit/Clip, With Sub, Master Mode,
Bluetooth™ Status
Flying Hardware| 2 x Top, 1 x Pullback
M8 Threading| 2 x Top, 1 x Pullback
M8 Threading
Bar Handles| 1 x Top| 1 x Side / 1 x Top
Pole Mount Adapter (1 3/8-inch/3.5cm)| 1 Bottom| 1 Bottom
Enclosure Materials| Polypropylene Cabinet| Polypropylene Cabinet
Grille| Powdered Coated Perforated Steel| Powdered Coated Perforated Steel
Dimensions (inches)| 11.14L x 12.17W x 18.39H| 12.68L x 15.20W x 25.28H
Dimensions (cm)| 28.3L x 30.9W x 46.7H| 32.2L x 38.6W x 64.2H
Weight (kg’s / lbs)| 12.6 / 27.7| 20.6 / 45.3

Block Diagram – NX Series

DESIGNED BY YORKVILLE SOUND

EYEBOLT INSTALLATION

1. DESCRIPTION
   Yorkville plastic speaker cabinets are equipped with flying hardware for overhead suspension applications. Depending on the model, two or more internal fly points have been provided for rigging purposes.
   IMPORTANT!!
   THE RIGGING OF LOUDSPEAKER SYSTEMS IS AN EXTREMELY SERIOUS MATTER. OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, INCLUDING (BUT NOT LIMITED TO) CALCULATING WORKING LOAD LIMITS, HARDWARE INSTALLATION, AND PERIODIC SAFETY INSPECTION OF ALL HARDWARE AND CABINETRY. IF YOU LACK THESE QUALIFICATIONS, DO NOT ATTEMPT THE INSTALLATION YOURSELF, BUT INSTEAD USE A PROFESSIONAL STRUCTURAL RIGGER. IMPROPER INSTALLATION CAN RESULT IN BODILY INJURY OR DEATH. CONSULT A STRUCTURAL ENGINEER TO CALCULATE ADDED LOADS FOR A BUILDING.
   STRUCTURAL REINFORCEMENT MAY BE NECESSARY TO INSURE A SAFE INSTALLATION.

2. REQUIRED TOOLS
   No.2 Drive Philips Screwdriver
   Thread lock adhesive (Removable Type)

3. EYEBOLT INSTALLATION
   a) Using a No.2 Drive Philips Screwdriver, remove the plastic cover screw from the top or bottom of the speaker enclosure to expose the tapped holes as shown below. Be sure to keep these handy to cover up the hole once the eyebolts are removed.
   IMPORTANT!!
   USE ONLY LOAD RATED FORGED EYEBOLTS.
   b) Place a drop of thread-lock adhesive on the threads of the eyebolt and insert one into exposed hole. Tighten each eyebolt by hand until its fits snugly against the cabinet. Further tighten each eyebolt by rotating it another half turn.
   Be sure to insert eyebolts in the threaded hole directly in-line with the suspension cable. Always follow the eyebolt manufacturers installation and use instructions.
   c) Suspend each cabinet according to working load calculations and practices recommended by the rigging hardware manufacturer.
   IMPORTANT!!
   YORKVILLE SOUND MAKES NO CLAIMS AS TO THE SAFETY OF THE ENCLOSURES OR RESULTANT INSTALLATION IF RECOMMENDED LOAD LIMITS AND HARDWARE INSTALLATION ARE NOT STRICTLY ADHERED TO.

4. WORKING LOAD LIMITS
   Specified working load limits have been determined for the enclosure as follows: MODEL| CONFIGURATION| SAFETY DESIGN FACTOR| THREAD| WORKING LOAD LIMIT
   ---|---|---|---|---
   NX8P| 2 top, 1 pullback| 10x| M8| weight of cabinet only
   NX12P| 2 top, 1 pullback| 10x| M8| weight of cabinet only

Two & Ten Year Warranty

Unlimited Warranty
Yorkville’s two and ten-year unlimited warranty on this product is transferable and does not require registration with Yorkville Sound or your dealer. If this product should fail for any reason within two years of the original purchase date (ten years for the wooden enclosure), simply return it to your Yorkville dealer with original proof of purchase and it will be repaired free of charge.
This includes all Yorkville products, except for the YSM Series studio monitors, Coliseum Mini Series and TX Series Loudspeakers.
Freight charges, consequential damages, weather damage, damage as a result of improper installation, damages due to exposure to extreme humidity, accident or natural disaster are excluded under the terms of this warranty. Warranty does not cover consumables such as vacuum tubes or par bulbs. See your Yorkville dealer for more details. Warranty valid only in Canada and the United States.

REAL Gear.
REAL People.
Canada
Voice: 905-837-8481
Fax: 905-839-5776
U.S.A.
Voice: 716-297-2920
Fax: 716-297-3689
www.yorkville.com
Yorkville Sound
550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA

Yorkville Sound Inc.
4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA
WEB: www.yorkville.com

WORLD HEADQUARTERS
CANADA
Yorkville Sound Limited
550 Granite Court
Pickering, Ontario
L1W 3Y8 CANADA
Voice: 905-837-8481
Fax: 905-839-5776
U.S.A.
Yorkville Sound Inc.
4625 Witmer Industrial Estate
Niagara Falls, New York
14305, USA
Voice: 716-297-2920
Fax: 716-297-3689
Quality and Innovation Since 1963
Printed in Canada
Manual-Owners-NX__P-00-1v0 • April 29, 2024
REAR-PAGE-00-5v1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>