Uniden X2K App Cam Solo User Guide

X2K App Cam Solo

“`html

Specifications:

• Camera: App Cam Solo X2K
• Power Port: DC 5V/1A
• SD Card Slot: Supports up to 256GB
• Battery: 5,200mAh rechargeable Li-h batteries
• Solar Panel: Optional 3W (SPS-X)
• PIR Detection Range: Customizable, up to 8 meters
• Compatibility: Works with My Uniden + App, supports Alexa &
  Google Home

Product Usage Instructions:

1. General Introduction:

The camera includes components such as lens, status light, fill
light (white light), IR light, PIR sensor, microphone, speaker,
power button, charging indicator, power port, reset button, and SD
card slot.

2. Powering On/Off:

To turn the camera on or off, press and hold the power button
for 3 seconds. The status light indicates the camera’s operational
status.

3. Camera Installation:

Before installation, ensure the solar panel receives adequate
sunlight. Adjust the camera angle and lock the screw in place
securely.

4. Solar Panel Installation (Optional):

Choose a location with maximum sunlight exposure throughout the
year for optimal solar panel performance.

5. Installing My Uniden + App:

To set up the camera, register an account on the app, log in,
and follow the on-screen instructions to add the camera to the
app.

FAQ:

Q: How can I customize the PIR detection range?

A: In the My Uniden + App, you can adjust the sensitivity level
to set the detecting distance for moving and living things as well
as moving vehicles. Higher sensitivity offers longer detecting
distance but may trigger more false alarms.

Q: What is the recommended installation height for the

camera?

A: It is advised to install the camera 2-3 meters above the
ground to maximize the motion sensor’s detection range.

Q: Are there limitations to motion detection?

A: Vertical movement towards the PIR sensor’s direction may lead
to motion detection limitations. Ensure moving objects approach
from different angles for accurate detection.

“`

App Cam Solo
X2K (1, -2, -4pcs)
Quick Start Guide

What’s in the Box

Camera

Bracket

Power cable

Screws

Owner’s Manual

Solar panel (3W) (SPS-X Optional)

1

General Introduction

Lens
Status light Fill light(white light)
IR light
PIR Microphone

Speaker

Power button
2

Charging indicator Power port Reset SD Card slot
Charging indicator:
· Charging. · Fully Charged.

General Introduction

Component Description

Power Port DC 5V/1A

Power ON/ OFF
Status light

Press and hold Power button for 3 seconds to Turn ON/ OFF camera
Red light flashes slowly: Camera start up and wait for connection. Red light flashes fast: Connecting the network. Solid Blue light: Camera is working correctly. Solid Red light: Camera is malfunction.

SD card slot Reset Battery

Support local SD Card storage (up to 256GB) Press and hold for 5 seconds to reset the camera 5,200mAh rechargeable Li-h batteries.

3

Camera Installation

!

• Before installation, please check the installation positions that will not affect the connection and usage, especially to ensure that the solar

panel can be fully illuminated.

Camera Installation

0~360°

0~90°
4

After adjust camera angel, lock the screw.

Solar Panel (3W) Installation (Optional)
Base

Locking Screw Cap Sleeve Rod

Locking Screw Cap 90°
Locking Screw Cap

30°
5

Solar Panel (3W) Installation (Optional)
Please select a position with the most sunlight throughout the year for your solar panel.
6

Install My Uniden + App
Download the My Uniden + App: · Apple Store: “My Uniden+” (for iOS), download and install the app. · Google Play Store: “My Uniden+” (for Android), download and install the app.
Support Alexa &Google Home
Set up the Camera
1. Register your account, tap “Sign up now” to create your account. 2. After you have the account, please log in.
7

Add Camera to My Uniden + App
Please follow the prompt tone to configure the camera

1

2

Tap “+” on the right top corner to Tap “Battery Camera”, choose

add device.

“Battery Camera”.

8

Add Camera to My Uniden + App
Please follow the prompt tone to configure the camera
Please Insert SD Card.

Hold the device power button to start the device.

Red light flashes slowly: Camera start up and wait for
connection.

More light settings, please

refer to p3- Status light.

3

4

9

Add Camera to My Uniden + App

5

6

Scan the QR code from the App. Keep your phone 15~25cm from the lens.

10

7
Connection successful , waiting to add to app

Add Camera to My Uniden + App

8

9

10

Connection successful.

Click to edit Camera name.

11

Camera Specification

· PIR Sensor Detecting Distance

The PIR detection range can be customized to meet your specific needs. You can refer to the following table to set it up in the My Uniden + App.

Sensitivity

Value

Low Mid High

1-4 5-7 8-10

Detecting Distance (For moving and living things)

Detecting Distance (For moving vehicles)

Up to 4 meters

Up to 4 meters

Up to 6 meters

Up to 6 meters

Up to 8 meters

Up to 8 meters

Note: Higher sensitivity offers longer detecting distance, but it would lead to more false alarms. You are advised to set up the sensitivity level to “1-4” or “5-7″ when you install the camera outdoors.

12

· PIR Sensor Installation Angle

Please install the camera 2-3 meters above the ground. The detection range of the motion sensor would be maximized at such a height.
For effective motion detection, please install the camera angularly and the angle between the PIR sensor and the detected object must be larger than 10°.
Due to the limitation of PIR sensor detection, please note that if a moving object approaches the PIR sensor vertically (the direction of the orange arrow in the image), the camera may fail to detect motion.

A

B

Mounting Height: 2-3 Meters
PIR Detecting Distance: 2-10 Meters

13

! Important Notes for Reducing False Alarms
For reducing false alarms, please note that: · Do not install the camera facing any objects with bright lights, including sunshine,
bright lamplights, etc. · Do not place the camera too close to a place where there are frequently moving
vehicles. The recommended distance between the camera and the vehicle is 15 meters. · Stay away from the outlets, including the air conditioner vents, humidifier outlets, the heat transfer vent of projectors, etc. · Do not install the camera facing the mirror. · Do not install the camera where there are strong winds · Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi routers and phones in order to avoid wireless interference.
14

Troubleshooting
Camera is not turning on
If your camera is not turning on, please apply the following solutions: · Make sure you press and hold the power button on for 3 seconds. · Charge the camera with a DC 5V/1A power adapter. When the blue light is on, the battery is fully charged.
Fail to scan the QR code on the phone
If the camera failed to scan the QR code on your phone, please apply the following solutions: · Remove the protective film on the lens of the camera. · Wipe the camera lens with a dry paper/ towel/tissue. · Vary the distance (about 30cm) between your camera and the mobile phone which enables the camera to focus better. · Increase the phone screen brightness and try scanning the QR code.
Wi-Fi connection failed during the initial setup process
If the camera fails to connect to Wi-Fi, please apply the following solutions: · Please make sure the band of the Wi-Fi network meet the requirement of the camera. · Please ensure you have entered the correct Wi-Fi password. · Put your camera close to your router to ensure a strong Wi-Fi signal. · Change the encryption method of the Wi-Fi network to WPA2 -PSK/WPA -PSK (safer encryption) on your router interface. · Set your password using only the characters on the keyboard.
15

Specifications

Model

Image Sensor

Video Resolution

Video Compression

Viewing Angle Video & Audio
PIR Detecting Distance

PIR Detecting Angle

Night Vision

Audio

Alerts

WiFi

WiFi

Wireless Security Max. User Access

Mobile Phone OS

Hardware

Battery Storage

Other Parameters

Temperature Size & Weight Waterproof Level

App Cam Solo X2K (1, -2, -4) 1/2.8” CMOS Image Sensor 2304 x 1296 (3.0Megapixel) H.264 H 110° / V 60° / D 135° Up to 10 meters Horizontal: 120° Up to 10 Meters Two-way talk PIR 2.4 GHz IEEE 802.11b/g/n
64/128-bit WPA/WPA2, WPA-PSK/WPA2-PSK, WPS 4
iOS 9 or later, Android 5 or later Lithium battery 5200mAh
Supports up to 256GB micro SD card, min class 10/Cloud storage Operating Temperature : -20°C~+50°C 64 x 59 x 101mm, 265g IP65 Weatherproof

16

WARRANTY
Uniden App Cam Solo X2K (1, -2, -4) Important:
Satisfactory evidence of the original purchase is required for warranty service. Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below.
Warrantor:
The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”). Terms of Warranty: Uniden Aust warrants to the original retail purchaser only that the Uniden App Cam Solo X2K (1, -2, -4) (“the Product”), will be free from defects in materials and craftsmanship for the duration of the warranty period, subject to the limitations and exclusions set out below.
Warranty Period: This warranty to the original retail purchaser is only valid in the original country of purchase for a Product first purchased either in Australia or New Zealand and will expire, as indicated below, from the date of original retail sale.

Product Accessories and Battery

1 Year 90 Days

If a warranty claim is made, this warranty will not apply if the Product is found by Uniden to be: A. Damaged or not maintained in a reasonable manner or as recommended in the relevant Owner’s Manual; B. Modified, altered or used as part of any conversion kits, subassemblies or any configurations not sold by Uniden Aust; C. Improperly installed contrary to instructions contained in the relevant Owner’s Manual D. Repaired by someone other than an authorized Uniden Repair Agent in relation to a defect or malfunction covered by this warranty; or E. Used in conjunction with any equipment, parts or a system not manufactured by Uniden.

Parts Covered: This warranty covers the Product and included accessories.
User-generated Data: This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation phone numbers, addresses and images)that may be stored on your Product.
Statement of Remedy: If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either repair the defect or replace the Product without any charge for parts or service. This warranty does not include any reimbursement or payment of any consequential damages claimed to arise from a Product’s failure to comply with the warranty.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty is in addition to and sits alongside your rights under either the COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER GUARANTEES ACT (New Zealand) as the case may be, none of which can be excluded.
Procedure for Obtaining Warranty Service: Depending on the country in which the Product was first purchased, if you believe that your Product does not conform with this warranty, you should deliver the Product, together with satisfactory evidence of your original purchase (such as a legible copy of the sales docket) to Uniden. Please refer to the Uniden website for address details. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty claim. Prior to delivery, we recommend that you make a backup copy of any phone numbers, images or other data stored on your Product, in case it is lost or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD Phone number: 1300 366 895 Email address: custservice@uniden.com.au

THANK YOU FOR BUYING A UNIDEN PRODUCT
© 2024 Uniden Australia Pty Limited V1.1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>