SOLT GGSSL900S 90cm Slide Out Rangehood User Guide

SOLT GGSSL900S 90cm Slide Out Rangehood

Product Information

Specifications

• Model: GGSSL900S
• Size: 90cm
• Controls: Off, Low Speed, High Speed, Light
• Recommended Installation Height: Minimum 650mm above cooktop

Product Usage Instructions`

Getting Started

Before installing and using the 90cm Slide-out Rangehood, ensure you have read the safety instructions in the user manual.

The Controls

• Off: Turns off the rangehood fan.
• Low Speed: Adjusts extraction to the lowest speed for regular cooking.
• High Speed: Adjusts extraction to the highest speed for heavy smoke or steam.
• Light: Press to turn the built-in lamp on and off.

Installation & First Use

• The typical installation method is into a purpose-built cupboard or wall mounting. Refer to the provided diagram for dimensions.
• Position the rangehood at a minimum height of 650mm above your cooktop for safety and performance.

FAQ

Q: What should I do before using the rangehood for the first time?

A: Make sure to read all safety instructions in the user manual before installation and use.

Q: How do I adjust the fan speed?

A: Use the Low-Speed setting for regular cooking and High Speed for heavy smoke or steam.

Q: What is the recommended height for mounting the rangehood?

A: The rangehood should be mounted at a minimum height of 650mm above your cooktop for safety and optimal performance.

Welcome

• Residentia Group
  • Congratulations on purchasing your new 90cm Slide-out Rangehood.
  • Sôlt is proudly distributed within Australia by Residentia Group Pty Ltd.
• Head Office 165 Barkly Avenue Burnley Victoria Australia 3121
  • Please refer to the warranty card at the rear of this manual for information regarding your product’s parts and labor warranty, or visit us online at: www.residentiagroup.com.au
• ACN 600 546 656
  • At Residential Group, we are customer-obsessed and our Support Team is there to ensure you get the most out of your appliance.
  • Should you want to learn more about your unit or how to take care of it, our Support Team is here to help.
• Online residential. groupwww.solt.house @solt.house
  • You can use our online Support Centre at any time by visiting: http://support.residentiagroup.com.au
• Postage PO BOX 5177, Burnley VIC Australia 3121
  • Or you can contact us via phone by dialling: 1300 11 HELP (4357).
• Telephone 1300 11 4357
  • It is important that you read through the following user manual thoroughly to familiarise yourself with the installation and operation requirements of your appliance to ensure optimum performance.
  • Again, thank you for choosing a Sôlt appliance and we look forward to being of service to you.
• Emailsupport@residentia.group
  • Kind Regards, The Residential Team

Customer Care

• Sôlt recommends the use of original spare parts.
• When contacting our customer service team by calling 1300 11 4357, or by emailing support@residentiagroup.com.au, please ensure that you have the following information at hand, which can be found on your appliances’ rating plate:
• Model Number
• Serial Number

Safety Information

Conditions of Use

This appliance is intended to be used in households and similar applications such as farmhouses or by customers in serviced apartments, holiday apartments, and other residential type of environments.

Before Installation & Maintenance

• Read these instructions carefully before installing or using this appliance. Ensure that you keep this manual on hand for future use. If you misplace this manual, a digital version can be found by visiting our website at www.solt.house
• Please make this information available to the person responsible for installing the appliance as it could reduce your installation costs.
• To avoid a hazard, this appliance must be installed according to these instructions for installation.
• This appliance is to be properly installed and earthed only by a suitably qualified person.
• Connection to a good earth wiring system is essential and mandatory.
• Disconnect the appliance from the electricity supply before carrying out any work or maintenance on it.
• This means that disconnection must be incorporated into the fixed wiring per the wiring rules.
• Alterations to the domestic wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death.
• The use of attachments is not recommended by the manufacturer and distributor as they may be hazardous.
• Failure to use caution could result in injury or cuts.
• This range hood is a domestic appliance that has been manufactured and tested to comply with Australian and New Zealand Standard AS/NZS 60335.2.31.
• IMPORTANT: Check for any damage or marks. If you find the appliance is damaged or marked, you must report it within 7 days if you wish to claim for damage or marks under the manufacturer’s warranty.
• This does not affect your statutory rights.
• Failure to install the appliance correctly could invalidate any warranty or liability claims.
• For further information regarding installation including a step-by-step guide, please refer to.

Operation & Maintenance

• WARNING: Follow these instructions carefully to avoid injury, electric shock, or fire.
• Ensure the rangehood is switched off before carrying out maintenance, to avoid any possibility of electric shock.
• Under no circumstances should children play with the appliance. Cleaning and user maintenance should never be undertaken by children without supervision.
• This appliance has not been designed to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or a lack of experience and knowledge, unless they have been given adequate supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Do not operate more than 4 cooktop burners at the same time. Never flambé under the rangehood.
• This range hood is not suitable for use over barbecues, and cannot be installed for external use; only indoors.
• The range hood and filters must be cleaned regularly to keep them in good working order.
• The exhaust from the rangehood must not be discharged into any heating flue, which may carry combustion products from other sources.
• Exhaust air must not be discharged into a wall cavity unless the cavity is designed for such a purpose. Regulations concerning the discharge of air must be met.
• There must be adequate ventilation in the room when the rangehood is used at the same time as appliances burning gas or other fuels.
• Your new rangehood is guaranteed against electrical or mechanical defects, subject to certain exclusions that are noted in the Warranty Terms and Conditions (at the rear of this user manual). The foregoing does not affect your statutory rights.
• Always cover lit gas burners with pots or pans when rangehood is in use. Ensure that gas burners are powered off before removing pots or pans.
• CAUTION: Never leave lit gas burners unattended or exposed due to the risk of fire. Regardless of whether cooking for long or short periods, the cooking process must be supervised continuously.
• For further information regarding operating instructions, please refer to.
• Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or other fuels (including those in other rooms) due to the backflow of combustion gases.
• These gases can potentially result in carbon monoxide poisoning.
• After installation of a range hood or other cooking fume extractor, the operation of flued gas appliances should be tested by a competent person to ensure that the backflow of combustion gases does not occur.

Exhaust Ducting Installation

• The following rules must be strictly followed to obtain optimal air extraction.
• Keep exhaust ducting short and straight.
• Do not reduce the size or restrict the exhaust duct.
• Keep bends in the exhaust duct to a minimum; the more bends the lower the extraction performance.
• When using flexible ducting always install the duct with the helix pulled taut to minimize pressure loss.
• Connect the extractor to the exhaust duct through a pipe with a minimum diameter of 120mm
• Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the range hood.
• Exhaust air must not be discharged into a wall cavity unless the cavity is designed for that purpose. The exhaust from the rangehood must not be discharged into any heating flue, which may carry combustion products from other sources.
• NOTE: Some installations may require the expandable/telescopic ducting to be cut to length. Cut with sharp tin snips or a fine-tooth hack saw blade, taking care not to distort or dent the exhaust cover.
• When using expandable ducting, it’s important to have the ducting fully taught to maximize the efficiency of the airflow.
• Important notice regarding the extraction mode.
• WARNING: Risk of poisoning from exhaust gases sucked back. Never operate the device in extraction mode simultaneously with an open flue appliance when there is not adequate airflow guaranteed.
• Open duct combustion equipment (for example, gas, oil, wood or coal-fired heaters, tankless water heaters, water heaters) pulls combustion air from the room and runs it through an exhaust pipe or chimney to the outside.
• In the extraction mode, indoor air is removed from the kitchen and the adjacent rooms — without sufficient air intake this creates a vacuum. Toxic gases from the chimney or extraction duct can thereby be sucked back into the living spaces.
• Always ensure that a sufficient supply of fresh air is guaranteed and that the air can circulate.
• An air supply/extractor box alone does not ensure compliance with the limit value.
• Safe operation is only possible when the negative pressure in the room where the appliance is located does not exceed 4 Pa (0.04 mbar).
• This can be achieved when the air required for combustion can flow through openings that are not closable, for example in doors, windows, in conjunction with an air supply/extractor box, or through other technical measures.
• In any case, consult a qualified chimney sweep who can assess the entire ventilation of your house and propose appropriate measures for adequate ventilation.
• If the rangehood is used exclusively in the recirculation mode, unrestricted operation is possible.
• During transportation, protective packaging was used to protect the appliance against any damage. After unpacking, please dispose of all elements of the packaging in a way that will not cause damage to the environment.

Disposal

• This appliance is labeled in compliance with European directive 2012/19/EC for Waste Electrical and Electronic Equipment (WEEE).
• By ensuring that this appliance is disposed of correctly, you will help prevent any possible damage to the environment and to human health, which might otherwise be caused if it were disposed of in the wrong way.
• The symbol on the product indicates that it may not be treated as normal household waste. It should be taken to a collection point for the recycling of electrical and electronic goods.
• This appliance requires specialist waste disposal. For further information regarding the treatment, recover, and recycling of this product please contact your local council, your household waste disposal service, or the shop where you purchased it.
• For more detailed information about the treatment, recovery, and recycling of this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.
• To disassemble your rangehood, perform the installation instructions in reverse order. Always perform disassembly with two people to avoid injuries.
• All materials used for packaging the appliance are environmentally friendly; they are 100% recyclable and are marked with the appropriate symbol.

Your Rangehood

GGSSL900S

Included Accessories

Installation Instructions

Installation Safety

• WARNING: Before starting the installation, please refer to the Safety Information section.
• Always switch the power off to the rangehood before beginning installation or maintenance.
• The exterior surfaces can be easily damaged during installation. Wherever possible, protect the rangehood with a cardboard box, plastic, or a towel.
• A power point must be located within 1.5m of the power cord exit from the rangehood, and it should be always accessible to allow isolation from power during cleaning or maintenance.
• All ducting must comply with building codes and local statutory requirements.
• If you are re-circulating the air as opposed to ducting, please ensure that the outlet grilles are not obstructed in any way, as this will affect the efficiency of the rangehood’s extraction.
• Ensure that the rangehood is mounted in a level position, both horizontally and vertically. This is essential to ensure the rangehood operates correctly, preventing lopsided grease build-up at either end.
• IMPORTANT: Never use silicone around your rangehood or flue pieces. Never install the rangehood or flue pieces into the plaster ceiling which prevents easy access to the rangehood for servicing requirements.
• IMPORTANT: Before installing your rangehood, please record the details of your rangehood’s rating label (located within the rangehood, behind the aluminum grease filters) into the form.
• This will be helpful should you need to contact our service team in the future.
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood. This distance shall be at least 65cm.
• If the instructions for installation specify a smaller distance, this has to be taken into account.
• The distance of 65cm can be reduced for non-combustible parts of range hoods, except grease filters, and parts operating at safety extra low voltage, provided these parts do not give access to live parts if deformed.

Electrical Connection

• Always check that the method of installation complies with the standards of local building, gas, and electrical authorities.
• Before connecting your range hood to the mains supply, ensure that the mains voltage corresponds to the voltage on the rating plate inside the range hood.
• Always wear proper protection during installation and maintenance. All work must be carried out by a qualified technician or similarly qualified person.
• IMPORTANT: Failure to install the appliance correctly could invalidate any warranty or liability claims.

Recirculating Installation

• Before beginning the installation of your rangehood, consider your ducting method. We recommend ducting your rangehood wherever possible to ensure maximum performance, however, this rangehood can be operated in recirculating mode.
• To operate in recirculating mode, you will need to purchase the relevant Carbon Filter accessory which is available for purchase via our After Sales Service Team.
• If you do not have an outlet to the outside, an exhaust pipe is not required. The rest of the installation method is the same as Ducted Installation.
• If you opt for recirculating installation, it is necessary to install the check valve on the vent hole, and the venting knob (shown below) is set to Circulating-Air Mode.

Check-Valve Installation

• Hold onto the check valve with your hands, align the box gap, place the check valve into the gap, and then rotate until the three groves of the check valve are secured.

Ducted Installation

• For maximum performance, we recommend installing with rigid or semi-rigid ducting. Use cable ties or suitable duct tape to secure the flexible pipe or ducting to the rangehood duct outlet.
• WARNING: All ducting must be fire retardant.
• Depending on your situation, there are multiple options for ducting your rangehood, as follows.
• Straight up through your tiled or metal roof, using a roof cowl (not supplied with the rangehood).
• Into your ceiling cavity (where compliant with local and national building regulations/codes. It may be necessary to seek approval from the relevant authority or building inspector where necessary.
• Into your ceiling cavity, and then vented through to the atmosphere through your eaves, using no more than 2 × 90° bends within the ducting run.
• Through your wall.
• IMPORTANT: Ducting can have a major effect on your rangehood’s performance. The following tips outline how to correctly duct your range hood.
• Always use the correct size ducting, and ensure that it is non-flammable ducting. For maximum performance, Sôlt recommends semi-rigid or rigid ducting.
• This range hood is designed for use with 120mm ducting to achieve optimum airflow performance and minimal noise during operation.
• To install a Ø 120mm air exhaust connection, insert the reducer flange on the hood body outlet. Fix the pipe in position using sufficient pipe clamps (not supplied).
• Always duct to the outside atmosphere, unless your local building codes and regulations permit otherwise.
• When using flexible ducting, always install the ducting pulled taut to minimize pressure loss, and cut any excess ducting off.
• Sôlt recommends you keep your total length of ducting to the shortest length possible. Where possible, avoid using 90° bends, and in their place use multiple 45°bends. Ensure there are no kinks in your ducting.
• For maximum performance, Sôlt recommends using cylindrical ducting whenever possible.

Positioning the Rangehood

• NOTE: When the rangehood and appliance supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4 × 10-5 Bar).
• IMPORTANT: The height of the rangehood underside must be a minimum of 650mm to a maximum of 750mm from the top of your cooktop surface (for gas cooktops this is the top of the gas burner).
• If the installation instructions for your cooktop specify a greater distance than the minimum, then that shall be the minimum height for installation.

Cupboard Mounting Installation

• IMPORTANT: Do not connect the power cable until the installation is complete! Sôlt recommends installing in a team of at least two people to avoid injuries.
• The typical installation method for your Sôlt rangehood is into a purpose-built cupboard or by wall mounting.
• IMPORTANT: It is not necessary to drill the 120mm diameter hole if your rangehood is to be configured using the recirculating air method.
• Drill a hole with a 120mm diameter and four 3.5mm diameter holes as per the diagram shown below.
• Insert the rangehood into the cabinet. Please ensure the flexible clips on both sides are fixed onto the cabinet.
• Use the 4 screws to fix the rangehood to a kitchen cupboard. Check that your fixings are correctly located, by temporarily fitting the range hood. If correct, fit the unit into position.
• Tighten the screws as necessary.
• WARNING: Failure to install the screws or fix the device under these instructions may result in electrical hazards.
• Please Note: The images in this user manual are for reference only. Your appliance may appear differently.

Wall Mounting Installation

• To mount your rangehood on the wall, drill two 10mm diameter holes 700mm apart aligning centered directly over the cooktop and with the vent hole on the top of the rangehood centered in the middle as well (as per the diagram shown below).
• Insert two supplied plastic wall plugs into the holes.
• Insert two screws into the upper two plastic wall plugs and tighten them leaving 3mm protruding from the wall.
• Mount the rangehood onto the two screws and mark the bottom two screw positions.
• Carefully remove the rangehood and drill the bottom two screw holes.
• Insert two supplied plastic wall plugs into the holes.
• Mount the rangehood on the top screws, insert the bottom screws, and fully tighten all the screws.
• WARNING: Failure to install the screws or fix the device under these instructions may result in electrical hazards.
• Sôlt recommends the wearing of proper protection during installation.
• Need Help? You can speak to our Support Team by calling 1300 11 4357, or simply reach out by emailing us at support@residentiagroup.com.au

Operating Instructions

Control Panel

• Please Note: The images in this user manual are for reference only. Your appliance may appear differently.

Control Panel Key

• Power Off
  • This setting will turn the rangehood fan off.
• Low Speed
  • This setting adjusts the extraction to the lowest speed. It is suitable for regular cooking, including simmering and cooking without much steam.
• High Speed
  • This setting adjusts the extraction to the highest speed. Use this fan setting for heavy smoke or steam to achieve maximum exhaust efficiency.
• Light
  • Press this switch to turn the built-in lamp on and off.

Cleaning & Maintenance

Cleaning Your Rangehood

Clean the Exterior Surface: with a soft cloth lightly dampened in lukewarm water, and thoroughly wrung. A compatible cleaning solution may also be used.

NOTE: To prevent any scratches, ensure that you use a soft cloth when cleaning the surface.

| Weekly Ensure the rangehood is powered off before commencing cleaning.
Clean the Controls: with a clean, soft cloth and a cotton swab. A compatible cleaning solution may also be used, with care.| Weekly Ensure the rangehood is powered off before commencing cleaning.
Clean the Grease Filters.

For more information please read ‘Cleaning Your Grease Filters.

| Monthly Ensure the rangehood is powered off before commencing cleaning.
Replace the Carbon Filters.

For more information see ‘Installing & Replacing the Carbon Filters.

| 2–3 Months Ensure the rangehood is powered off before commencing cleaning.

Cleaning Safety

• Maintenance and inspection should be undertaken frequently.
• If there is any visible damage, a strong odor, or excessive overheating of components, stop using the appliance and contact our After Sales Support Team by calling 1300 11 4357 or by emailing support@residentiagroup.com.au for assistance.
• Always ensure that the rangehood is powered off and the plug has been removed before any cleaning or maintenance is performed.
• Avoid trying to clean any electrical or electronic parts, as this may damage the rangehood or present a risk of electric shock.
• Always let the rangehood and its components cool down before cleaning them.
• When cleaning the rangehood, do not use any acrid or corrosive detergents, or abrasive wipes, chemicals, or alcohol as these could damage the surface.
• Avoid using any abrasive detergents or any alkaline dishwasher detergents as these could also damage the surface.
• CAUTION: DO NOT under any circumstances use a steam cleaner when cleaning your range hood.
• Always clean and maintain the appliance under the instructions found in this user manual. Failure to do so may compromise your warranty or result in a risk of fire or electric shock.
• Water must not enter into electrical parts such as the motor, control switch, etc. as this presents a high risk of electric shock.

Cleaning the Grease Filters

• Soak the filter in your kitchen sink for approximately 3 minutes in a max of 30º C water with a mild, non-corrosive grease-removing detergent.

Alternatively:

• Place the filter in the dishwasher and run a program with a mild non-corrosive grease-removing detergent.
• Note that it is not advisable to use rinse aids. Ensure that the program does not exceed 30º C.
• Always wash the filter separately from the crockery and kitchen utensils.
• Brush the filter gently with a soft brush. Do not apply too much pressure to avoid damaging the filter.
• Over time, fading and discoloration may happen. This is normal and is not considered a warranty issue.
• Leave the filter to dry naturally out of direct sunlight.
• Once dry, gently fit the filter back into position.

Installing and Replacing the Carbon Filters

• The carbon filters are an optional spare part available to purchase by contacting our After Sales Support Team.
• WARNING: DO NOT clean or wash your carbon filters.
• If carbon filters are used, Sôlt recommends replacing the carbon filters every 2 to 3 months.

1. Disconnect the power supply from the wall socket and carefully remove both grease filters.
2. Install or replace a carbon filter by gently slotting the filter in, and turning it clockwise to secure.
3. Place both grease filters back into position, and then reconnect the power supply to the wall socket.

Replacing the Light Bulb

• A replacement light is available to purchase by contacting our After Sales Support Team.
• WARNING: Only a qualified electrician or authorized service agent may replace the globe. Always let the globe cool down before replacing it as it may be hot.
• Always use gloves or a cloth to avoid direct contact between the light bulb and your hands.
• Direct contact may reduce the lifespan of the globe.

1. Disconnect the power supply from the wall socket and carefully remove both grease filters.
2. Remove the light bulb by levering its fitting from the rangehood body. This may require slight pressure or force to be applied.
3. Disconnect the light from its fastening.
4. Replace the light ensuring it is the same type as specified in the table below.
5. Place both grease filters back into position, and then reconnect the power supply to the wall socket.

Self-Ballasted LED Modules

Max. Power| 1.5W
Voltage| 220–240V~
Dimensions| 33.2mm × 120mm
Image|

Troubleshooting

For Minor Faults

further guidance.
The blades may be blocked.| Call our After Sales Support Team.
Both the light and motor do not work properly.| The fuse or light may be damaged.| Reset or replace the fuse or light.
The power supply cord may be loose or disconnected.| Reconnect the power supply to the wall socket.
The light is not working.| The light globes may be damaged or may have blown.| Refer to the Light Replacement section or call our After Sales Support Team.
The is insufficient suction power or air is not extracted adequately.| The distance between the range hood and the cooktop may be too great.| Re-adjust the installation position, ensuring that the minimum distances are observed as per.
Ducting may be loose, kinked, too long, or have too many bends.| Check that your rangehood has been ducted correctly and by the installation instructions.
The range hood is vibrating against the wall or cabinetry.| The range hood body may not be fixed in place correctly.| Fix the body tightly and ensure that all installation steps are done correctly.
The motor may not be tightly hung.| Lock in the motor tightly.
The fan blade may be damaged.| Call our After Sales Support Team.
Oil is leaking from the range hood.| The outlet and the air ventilation entrance are not tightly sealed.| Carefully take down the outlet and re-seal it with glue.
Leakage from the connection of the U-shaped section and cover.| Take a U-shaped section down and seal it with soap or paint.
The rangehood inclines.| The fixing/hanging screws are loose.| Tighten the fixing or hanging screws.

For Serious Faults

• Some minor faults can be fixed by referring to the table above, however, if an emergency or serious fault occurs, immediately disconnect the rangehood from your electricity supply and contact After Sales Support.
• If a serious fault occurs, DO NOT attempt to repair the rangehood yourself, instead wait for an authorized service agent or similarly qualified person to do so.
• For assistance or to organize an authorized service agent contact our After Sales Support by calling 1300 11 4357, or by emailing support@residentiagroup.com.au.
• Please note that if a service agent is asked to attend whilst the product is under warranty and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.

Technical Specifications

please email parts@residentiagroup.com.au to learn more
Lighting| 2 × 1.5W LED
Max. Noise Rating| 71 dB(A)
Power Supply| 220–240V~, 50Hz
Product Dimensions (W × D × H mm)| 895 × 298 × 175 mm
Installation| Cupboard or Wall Mountable

Purchase Details

• For future reference, please record the following information which can be found on the rating plate, and the date of purchase which can be found on your sales invoice.
• STORE DETAILS………………………….
• STORE NAME…………………………
• ADDRESS…………………………………
• TELEPHONE ………………………………….
• PURCHASE DATE.. ……………………………….
• PRODUCT DETAILS… ………………………………
• MODEL NO. ……………………………………………..
• SERIAL NO. ………………………………………………..

Warranty Information

WARRANTY TERMS AND CONDITIONS RANGE HOOD

• This document sets out the terms and conditions of the product warranties for Residential Group Appliances. It is an important document.
• Please keep it with your proof of purchase documents in a safe place for future reference should you require service for your Appliance.

1. IN THIS WARRANTY

   • (a) ‘acceptable quality’ as referred to in clause 10 of this warranty has the same meaning referred to in the ACL;
   • (b) ‘ACL’ means Trade Practices Amendment (Australian Consumer Law) Act (No.2) 2010;
   • (c) ‘Appliance’ means any Residentia Group product purchased by you accompanied by this document;
   • (d) ‘ASR’ means Residentia Group authorized service representative;
   • (e) ‘Residential Group’ means Residential Group Pty Ltd of 165 Barkly Ave, Burnley VIC 3121, ACN 600 546 656 in respect of Appliances purchased in Australia;
   • (f ) ‘major failure’ as referred to in clause 10 of this warranty has the same meaning referred to in the ACL and includes a situation when an Appliance cannot be repaired or it is uneconomic for Residentia Group, at its discretion, to repair an Appliance during the Warranty Period;
   • (g) ‘Warranty Period’ means:
   • (i) where the Appliance is used for personal, domestic, or household use (i.e. normal single-family use) as set out in the instruction manual, the Appliance is warranted against manufacturing defects for 24 months, following the date of the original purchase of the Appliance;
   • (h) ‘you’ means the purchaser of the Appliance not having purchased the Appliance for re-sale, and ‘your’ has a corresponding meaning.

2. This warranty only applies to Appliances purchased and used in Australia and is in addition to (and does not exclude, restrict, or modify in any way) any non-excludable statutory warranties in Australia.

3. During the Warranty Period Residentia Group or its ASR will, at no extra charge if your Appliance is readily accessible for service, without special equipment and subject to these terms and conditions, repair or replace any parts which it considers to be defective. Residentia Group or its ASR may use remanufactured parts to repair your Appliance. You agree that any replaced Appliances or parts become the property of Residential Group. This warranty does not apply to light globes, batteries, seals, filters, or similar perishable parts.

4. Parts and Appliances not supplied by Residentia Group are not covered by this warranty.

5. You will bear the cost of transportation, travel, and delivery of the Appliance to and from Residentia Group or its ASR. If you reside outside of the service area, you will bear the cost.

   • (a) travel of an authorized representative;
   • (b) transportation and delivery of the Appliance to and from Residentia Group or its ASR, in all instances, unless the Appliance is transported by Residentia Group or its ASR, the Appliance is transported at the owner’s cost and risk while in transit to and from Residentia Group or its ASR.

6. Proof of purchase is required before you can claim this warranty.

7. You may not make a claim under this warranty unless the defect claimed is due to defective parts or workmanship. Residential Group is not liable in the following situations (which are not exhaustive).

   • (a) The appliance is damaged by:
   • accident
   • misuse or abuse, including failure to properly maintain or service
   • normal wear and tear
   • power surges, electrical storm damage, or incorrect power supply
   • incomplete or improper installation
   • incorrect, improper, or inappropriate operation
   • insect or vermin infestation
   • failure to comply with any additional instructions supplied with the Appliance;
   • (b) the Appliance is modified without authority from Residential Group in writing;
   • (c) the Appliance’s serial number or warranty seal has been removed or defaced;
   • (d) The appliance was serviced or repaired by anyone other than Residential Group, an authorized repairer, or ASR.

8. This warranty, the contract to which it relates, and the relationship between you and Residentia Group are governed by the law applicable where the Appliance was purchased.

9. To the extent permitted by law, Residential Group excludes all warranties and liabilities (other than as contained in this document) including liability for any loss or damage whether direct or indirect arising from your purchase, use, or nonuse of the Appliance.

10. For Appliances and services provided by Residentia Group in Australia, the Appliances come with a guarantee by Residentia Group that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a major failure. The benefits to you given by this warranty are in addition to your other rights and remedies under a law concerning the Appliances or services to which the warranty relates.

11. At all times during the Warranty Period, Residentia Group shall, at its discretion, determine whether repair, replacement, or refund will apply if an Appliance has a valid warranty claim applicable to it.

12. Missing parts are not covered by warranty.
    Residential Group reserves the right to assess each request for missing parts on a case-by-case basis.
    Any parts that are not reported missing in the first week after purchase will not be provided free of charge.

13. To enquire about claiming under this warranty, please follow these steps.

    • (a) carefully check the operating instructions, user manual, and the terms of this warranty;
    • (b) have the model and serial number of the Appliance available;
    • (c) have the proof of purchase (e.g. an invoice) available;
    • (d) telephone the numbers shown below.

14. You accept that if you make a warranty claim, Residential Group and its ASR may exchange information concerning you to enable Residentia Group to meet its obligations under this warranty.

• IMPORTANT Before calling for service, please ensure that the steps in point 13 have been followed.
• CONTACT SERVICE Please call 1300 11 HELP (4357)
• The Australian Consumer Law requires the inclusion of the following statement with this warranty:
• Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
• You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
• T. 1300 11 4357
• E.support@residentiagroup.com.au
• www.solt.house

Documents / Resources

| SOLT GGSSL900S 90cm Slide Out Rangehood [pdf] User Guide
GGSSL900S 90cm Slide Out Rangehood, GGSSL900S, 90cm Slide Out Rangehood, Slide Out Rangehood, Rangehood
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>