the t mix 422796 1402 FXMP USB Mixer User Manual

: July 29, 2024
: the t mix

The t.mix 422796 1402 FXMP USB Mixer

the t mix 422796 1402 FXMP USB Mixer

USER MANUAL

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
Internet: www.thomann.de
19.02.2024, ID: 422796 (V5)

1. General information

This document contains important instructions for the safe operation of the product. Read and follow the safety instructions and all other instructions. Keep the document for future reference. Make sure that it is available to all those using the product. If you sell the product to another user, be sure that they also receive this document.
Our products and documentation are subject to a process of continuous develop‐ment. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de.

1.1 Symbols and signal words

In this section you will find an overview of the meaning of symbols and signal words that are used in this document.

Signal word	Meaning
DANGER!	This combination of symbol and signal word indicates an immediate

dangerous situation that will result in death or serious injury if it is not avoided.
WARNING!| This combination of symbol and signal word indicates a possible dangerous situation that can result in death or serious injury if it is not avoided.
NOTICE!| This combination of symbol and signal word indicates a possible dangerous situation that can result in mate‐ rial and environmental damage if it is not avoided.
|
Warning signs| Type of danger
| Warning – high-voltage.
| Warning – danger zone.

2. Safety instructions

Intended use

This device is intended to be used for amplification, mixing and playback of signals from musical instruments and microphones. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intel‐lectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.

Safety

DANGER!

Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can injure themselves when handling the device. Never allow children to play with the packaging material and the device. Always store packaging material out of the reach of babies and small children. Always dispose of packaging material properly when it is not in use. Never allow children to use the device without supervision. Keep small parts away from children and make sure that the device does not shed any small parts (such knobs) that children could play with.

DANGER!

Danger to life due to electric current!
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device when covers, safety equipment or optical components are missing or damaged.

DANGER!

Danger to life due to electric current!
A short circuit could lead to a fire hazard and risk of death. Always use proper ready-made insulated triple-core mains cable with a safety plug. Do not modify the mains cable or the plug. In case of isolation damage, disconnect immediately the power supply and arrange repair. If in doubt, seek advice from a qualified electrician.

WARNING!

Possible hearing damage due to high volumes on speakers or headphones!
With speakers or headphones connected, the device can produce volume levels that may cause temporary or permanent hearing impairment. Over an extended period of time, even levels that seem to be uncritical can cause hearing damage. Do not operate the device permanently at a high volume level. Decrease the volume level immediately if you experience ringing in your ears or hearing impairment.

NOTICE!

Risk of fire due to covered vents and neighbouring heat sources!
If the vents of the device are covered or the device is operated in the immediate vicinity of other heat sources, the device can overheat and burst into flames. Never cover the device or the vents. Do not install the device in the immediate vicinity of other heat sources. Never operate the device in the immediate vicinity of naked flames.

NOTICE!

Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient conditions. Only operate the device indoors within the ambient conditions specified in the “Technical specifications” chapter of this user manual. Avoid operating it in environments with direct sunlight, heavy dirt and strong vibrations. Avoid operating it in environments with strong temperature fluctuations. If temperature fluctuations cannot be avoided (for example after transport in low outside temperatures), do not switch on the device immediately. Never subject the device to liquids or moisture. Never move the device to another location while it is in oper‐ation. In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by qualified specialists at regular intervals to prevent damage due to overheating and other malfunctions.

NOTICE!

Damage to the device due to high voltages!
The device can be damaged if it is operated with the incorrect voltage or if high voltage peaks occur. In the worst case, excess voltages can also cause a risk of injury and fires. Make sure that the voltage specification on the device matches the local power grid before plugging in the device. Only operate the device from professionally installed mains sockets that are protected by a residual current circuit breaker (FI). As a precaution, disconnect the device from the power grid when storms are approaching or it the device will not be used for a longer period.

NOTICE!

Danger of short circuit due to use of unbalanced XLR cables!
The device has a phantom voltage input. Using unbalanced cables with the phantom power may damage the device. Use only balanced cables. Before switching on phantom power, always make sure that no unbalanced wired cables are connected.

NOTICE!

Risk of fire due to installation of a wrong fuse!
Using fuses of a different type than compatible with the device may cause a fire and seriously damage the device. Only use fuses of the same type. Observe the labelling on the device casing and the information in the “Technical data” chapter.

NOTICE!

Possible staining due to plasticiser in rubber feet!
The plasticiser contained in the rubber feet of this product may react with the coating of the floor and cause permanent dark stains after some time. If necessary, use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and the floor.

3. Features

12-channel mixer with built-in FX processor
Bluetooth interface for transferring music files
8 mono channels (MIC, line) with switchable phantom power and low cut
3-band EP and pan control
Control room output L/R (1/4″ phone sockets)
Additional RCA connections (stereo in / rec out)
1 × AUX control per channel, PRE/POST selectable
PFL switch per channel
Master output L/R via 2 × XLR and 2 × 1/4″ phone socket
Headphones output, 1/4″ phone socket (stereo)
Headphones adjustable together with CTRL room out
USB port
48 V phantom power, globally switchable
Built-in power supply

4. Installation and starting up

Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.

Before connecting the supply voltage and before connecting or disconnecting audio cables, set all volume controls of the unit to zero to avoid damage to the connected speakers and devices.

5. Connections and controls

Mono channel strip

Stereo channel strip

Effects section, AUX

NENU

Connections and controls

53 [+48V] LED | This LED lights up when the phantom power is on.
54 [+48V] switch | When this switch is in the ON position, a phantom voltage of 48 V is present on the XLR sockets in the mono channels for using condenser microphones. If no condenser microphones are used, the switch should be in the OFF position. The phantom voltage must not be switched on if an unbalanced XLR cable is connected to one of the MIC inputs.
55 [POWER] | This LED lights up when the device is on.
56 [LEDs] | These LED chains indicate the level of the sum signal. Keep the level within a range below +18. The red LEDs light up if there is an overload. In this case, pull back the two master faders so that the red LEDs do not light up any more. If the PFL button is pressed in one of the channels, the signal in this channel is displayed in the left LED chain, regardless of the channel fader.
57 [PFL] | This LED lights up when the [PFL] button is pressed in at least one of the channels and thus the LED chains do not display the sum signal.
58 [CR & PHONES] | Rotary control for adjusting the level on the outputs [CR OUT] and [PHONES].
59 [L MIX R] | Master fader for adjusting the sum level on the outputs [MAIN OUTPUT], [CR OUT] and [PHONES].

Back

60, 61 [MAIN OUTPUTS] | Balanced 6.3-mm jack outputs for connecting power amplifiers, effects devices or recording devices
62, 63 [MAIN OUTPUTS] | Balanced XLR outputs for connecting power amplifiers, effects devices or recording devices.
64 [POWER] | Main switch for turning the device on and off.
65 [SIGNAL] | Rubber panel plug for mains connection with fuse holder.

Connection example – club gig

6. Technical specifications

Technical specifications

Further information

Further information

7. Plug and connection assignment

Introduction

This chapter will help you select the right cables and plugs to connect your valuable equipment in such a way that a perfect sound experience is ensured.
Please note these advices, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into the socket, an incorrect connection may result in a destroyed power amp, a short circuit or ‘just’ in poor transmission quality!

Balanced and unbalanced transmis‐sion

Unbalanced transmission is mainly used in semi-professional environment and in hifi use. Instrument cables with two conductors (one core plus shielding) are typical rep‐resentatives of the unbalanced transmission. One conductor is ground and shielding while the signal is transmitted through the core.

Unbalanced transmission is susceptible to electromagnetic interference, especially at low levels, such as microphone signals and when using long cables.

In a professional environment, therefore, the balanced transmission is preferred, because this enables an undisturbed transmission of signals over long distances. In addition to the conductors ‘Ground’ and ‘Signal’, in a balanced transmission a second core is added. This also transfers the signal, but phase-shifted by 180°.

Since the interference affects both cores equally, by subtracting the phase- shifted signals, the interfering signal is completely neutralized. The result is a pure signal without any noise interference.

1/4″ TS phone plug (mono, unbal‐anced)

TS phone plug

Plug and connection assignment

8. Protecting the environment

Disposal of the packing material

Environmentally friendly materials have been chosen for the packaging. These mate‐rials can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are dis‐posed of in the proper manner.
Do not dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the instructions and markings on the packaging.

Observe the disposal note regarding documentation in France.

Disposal of your old device

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) as amended.

Do not dispose of your old device with your normal household waste; instead, deliver it for controlled disposal by an approved waste disposal firm or through your local waste facility. When disposing of the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste management facility. Proper disposal protects the environment as well as the health of your fellow human beings.

Also note that waste avoidance is a valuable contribution to environmental protec‐tion. Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal.

You can return your old device to Thomann GmbH at no charge. Check the current conditions on www.thomann.de.

If your old device contains personal data, delete those data before disposing of it.

FAQ (Frequently Asked Questions)

Q: Can the xmix 1402 FXMP USB Mixer be used with all types of musical

instruments?

A: The mixer is designed for use with various musical instruments and microphones. However, ensure compatibility and follow the user manual guidelines for best results.