the t mix 424898 MicroMix 2 USB Canaux Avec Bluetooth User Manual
- June 1, 2024
- the t mix
Table of Contents
- the t mix 424898 MicroMix 2 USB Canaux Avec Bluetooth
- Safety instructions
- Features
- Installation and starting up
- Connections and controls
- Technical specifications
- Plug and connection assignment
- Introduction
- Protecting the environment
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
the t mix 424898 MicroMix 2 USB Canaux Avec Bluetooth
General information
- This document contains important instructions for the safe operation of the product. Read and follow the safety instructions and all other instructions. Keep the document for future refer‐ence. Make sure that it is available to all those using the product. If you sell the product to another user, be sure that they also receive this document.
- Our products and documentation are subject to a process of continuous development. They are therefore subject to change. Please refer to the latest version of the documentation, which is ready for download under www.thomann.de.
Symbols and signal words
In this section you will find an overview of the meaning of symbols and
signal words that are used in this document.
Signal word | Meaning |
---|---|
DANGER! | This combination of symbol and signal word indicates an |
immediate dangerous situation that will result in death or serious injury if
it is not avoided.
WARNING!| This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in death or serious injury if it is
not avoided.
NOTICE!| This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in material and environmental damage
if it is not avoided.
|
Warning signs| Type of danger
| Warning – danger zone.
Safety instructions
Intended use
- This device is intended to be used for amplification, mixing and playback of signals from musical instruments and microphones. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
- This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.
Safety
DANGER: Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can
injure themselves when handling the device. Never allow children to play with
the packaging material and the device. Always store packaging material out of
the reach of babies and small children. Always dispose of packaging material
properly when it is not in use. Never allow children to use the device without
supervi‐sion. Keep small parts away from children and make sure that the
device does not shed any small parts (such knobs) that children could play
with.
WARNING!
Possible hearing damage due to high volumes on speakers or headphones!
With speakers or headphones connected, the device can produce volume levels
that may cause temporary or permanent hearing impairment. Over an extended
period, even levels that seem to be uncritical can cause hearing damage. Do
not operate the device permanently at a high volume level. Decrease the volume
level immediately if you experience ringing in your ears or hearing
impairment.
NOTICE!
Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient conditions.
Only operate the device indoors within the ambient conditions specified in the
“Technical specifications” chapter of this user manual. Avoid operating it in
environments with direct sunlight, heavy dirt, and strong vibrations. Avoid
operating it in environments with strong temperature fluctuations. If
temperature fluctuations cannot be avoided (for example after transport in low
outside temperatures), do not switch on the device immediately.
Never subject the device to liquids or moisture. Never move the device to
another location while it is in operation. In environments with increased dirt
levels (for example due to dust, smoke, nicotine or mist): Have the device
cleaned by qualified specialists at regular intervals to prevent damage due to
overheating and other malfunctions.
NOTICE!
The danger of short circuits due to the use of unbalanced XLR cables!
The device has a phantom voltage input. Using unbalanced cables with the
phantom power may damage the device. Use only balanced cables. Before
switching on phantom power, always make sure that no unbalanced wired cables
are connected.
Features
- 5-channel mixer
- 1 × mono channel with XLR / 1/4″ combo socket (MIC / Line), gain adjustment, 2-band EQ and pan control
- 1 × stereo channel with RCA sockets (line), 2-band EQ and balance control
- 1 × stereo channel with RCA sockets (line)
- 18 V phantom power permanently present on the XLR input
- Headset with headphone and microphone connectable (3.5 mm jack)
- 1 × stereo RCA output
- USB port for use as an audio interface
- Built-in Bluetooth module for wireless sources
- Power supply via USB port
Installation and starting up
Unpack and check carefully there is no transportation damage before using the
unit. Keep the equipment packaging. To fully protect the product against
vibration, dust and moisture during transportation or storage use the original
packaging or your own packaging material suitable for transport or storage,
respectively.
Create all connections while the device is off. Use the shortest possible
high-quality cables for all connections. Take care when running the cables to
prevent tripping hazards.
Connections and controls
- [USB TO COMPUTER] | USB port for connecting to a computer for use as an audio interface and for power supply.
- [MONITOR – MIC] | For connecting the microphone when using a headset, signal processing via channel 1.
- [POWER] | The LED lights when the device is on.
- [ON / OFF] | On and off switch
- [MONITOR – HEADSET] | For connecting the headphones if a headset is in use.
- [2-TK / BT TO] | When the switch is pressed, the Bluetooth and 2-TK input signals are assigned to the ‘Monitor’ output, otherwise to the ‘MAIN MIX’ output and the USB port.
- [PAIR] | This switch must be pressed to allow the device to pair with Bluetooth sources. The blue LED above the switch indicates the Bluetooth status: 1 × flash every second: Ready to make the connection. 1 × flash every 5 seconds: Connected. 2 × flashes every 5 seconds: Connection interrupted.
- [MONITOR] | Volume control for the monitor output.
- [L – CLIP – R] | The ‘L’ or ‘R’ LED lights up green when a signal is present on the respective bus side. It lights up red when an overload occurs on the respective bus side. In this case, lower the input levels that could be causing the overload or turn the ‘MAIN MIX’ control anti-clockwise.]
- [MAIN MIX] | Volume control for the ‘MAIN MIX’ output and the USB port.
- [CH 2/3] | Level control for the signals on input ‘CH2/3’ and on the USB port.
- [CH1] | Level control for the signals on input ‘CH1’ .
- [PEAK] | This LED lights up in case of an overload in channel 1. In this case, turn the [GAIN] control anti-clockwise until the LED goes out.
- [HIGH – LOW – PAN] | Tone and pan control for channel ‘CH1’ . Push the ‘HIGH’ control up or down to raise or lower the treble. Slide the ‘LOW’ control up or down to raise or lower the bass. Slide the ‘PAN’ control up or down to move the signal source further to the left or right in the stereo panorama.
- [HIGH – LOW – PAN] | Tone and pan control for channel ‘CH2/3’ . Push the ‘HIGH’ control up or down to raise or lower the treble. Slide the ‘LOW’ control up or down to raise or lower the bass. Slide the ‘BAL’ control up or down to increase the loudness of the left or right channel of the signal source.
- [GAIN] | Control for adjusting the sensitivity of input ‘CH1’ .
- [LINE / USB – FROM] | When this switch is pressed, the signals present on the USB port will be played, otherwise those on the ‘LINE IN’ input.
- [LINE / USB – TO] | When the switch is pressed, the channel signal is present on the ‘MONITOR’ output, otherwise on the ‘MAIN MIX’ output.
- [CH1 INPUT] | Balanced XLR / jack input for connecting a microphone (XLR) or a line-level signal source (6.3-mm jack). The XLR socket provides permanent 18 V phantom power for connecting condenser microphones. Never connect unbal‐anced cables to this socket, otherwise, the unit will be damaged.
- [INPUT – LINE IN] | Stereo cinch input for line-level signals, e.g. CD or MP3 player.
- [INPUT – 2-TK] | Additional stereo cinch input for line-level signals.
- [MAIN MIX] | Stereo cinch output for the final signal mix of the device. Here you can connect a power amplifier, powered speakers or a recording device.
Technical specifications
Input connections | Microphone input | Type | XLR panel socket, 3-pin, balanced |
---|---|---|---|
Level | 2 mV | ||
Impedance | 1.8 kΩ (max. gain) | ||
Line input | Type | 6.3-mm jack socket, balanced | |
Level | 10 mV | ||
Impedance | 12 kΩ | ||
Stereo cinch input | Type | 4 × cinch socket | |
Level | 30 mV | ||
Impedance | 20 kΩ | ||
Microphone input | Type | 3.5-mm jack socket | |
USB port | Type | USB 1.1 compatible, 16 bit Delta-Sigma | |
Sampling rates | 44.1 kHz, 48 kHz | ||
Output connections | Stereo cinch output | Type | 2 × cinch socket |
Level | max. 5.8 V | ||
Headphone output | Type | 3.5-mm jack socket | |
--- | --- | --- | --- |
Impedance | ≥ 16 Ω | ||
EQ | Bass | ± 15 dB/80 Hz | |
Treble | ± 15 dB/12 kHz | ||
Frequency range | 20 Hz … 22 kHz | ||
Signal-to-noise ratio | 80 dB, A-weighted | ||
Total harmonic distortion (THD) | ≤ 0.05% | ||
Phantom power | +18 V | ||
Power supply | Via computer (USB port) or |
USB mains adapter 5 V/500 mA (not included)
Dimensions (W × H × D)| 100 mm × 40 mm × 135 mm
Weight| 430 g
Ambient conditions| Temperature range| 0 °C…40 °C
Relative humidity| 20%…80% (non-condensing)
Plug and connection assignment
Introduction
- This chapter will help you select the right cables and plugs to connect your valuable equipment in such a way that a perfect sound experience is ensured.
- Please note this advice, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into the socket, an incorrect connection may result in a destroyed power amp, a short circuit, or ‘just’ poor transmission quality!
Balanced and unbalanced trans‐mission
- Unbalanced transmission is mainly used in semi-professional environments and in hifi use. Instrument cables with two conductors (one core plus shielding) are typical representatives of the unbalanced transmission. One conductor is ground and shielding while the signal is trans‐mitted through the core.
- Unbalanced transmission is susceptible to electromagnetic interference, especially at low levels, such as microphone signals, and when using long cables.
- In a professional environment, therefore, the balanced transmission is preferred, because this enables an undisturbed transmission of signals over long distances. In addition to the conductors ‘Ground’ and ‘Signal’, in a balanced transmission, a second core is added. This also transfers the signal but phase-shifted by 180°.
- Since the interference affects both cores equally, by subtracting the phase-shifted signals, the interfering signal is completely neutralized. The result is a pure signal without any noise interference.
1/4″ TS phone plug (mono, unbalanced)
1 | Signal |
---|---|
2 | Ground, shielding |
1/4″ TRS phone plug (mono, bal‐anced)
1 | Signal (in phase, +) |
---|---|
2 | Signal (out of phase, –) |
3 | Ground |
XLR plug (balanced)
1 | Ground, shielding |
---|---|
2 | Signal (in phase, +) |
3 | Signal (out of phase, –) |
4 | Shielding on plug housing (option) |
XLR plug (unbalanced)
1 | Ground, shielding |
---|---|
2 | Signal |
3 | Bridged to pin 1 |
Three-pole 1/8″ mini phone jack (stereo, unbalanced)
1 | Signal (left) |
---|---|
2 | Signal (right) |
3 | Ground, shielding |
RCA connection
1 | Signal |
---|---|
2 | Ground, shielding |
Drawing and table indicate the pin assignment of an RCA plug.
RCA connection
Protecting the environment
Disposal of the packing material
- Environmentally friendly materials have been chosen for the packaging. These materials can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are disposed of in the proper manner.
- Do not dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the instructions and markings on the packaging.
- Observe the disposal note regarding documentation in France.
Disposal of your old device
- This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) as amended.
- Do not dispose of your old device with your normal household waste; instead, deliver it for controlled disposal by an approved waste disposal firm or through your local waste facility. When disposing of the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste management facility. Proper disposal protects the environment as well as the health of your fellow human beings.
- Also, note that waste avoidance is a valuable contribution to environmental protection. Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal.
- You can return your old device to Thomann GmbH at no charge. Check the current conditions on www.thomann.de.
- If your old device contains personal data, delete that data before disposing of it.
Thomann GmbH
- ADDRESS: Hans-Thomann-Straße 1 96138 Burgebrach Germany
- Telephone: +49 (0) 9546 9223-0
- Internet: www.thomann.de
19.02.2024, ID: 424898 (V2)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>