MARMITEK Subwoofer Anywhere 640 Transmitter and Receiver User Guide
- June 3, 2024
- MARMITEK
Table of Contents
MARMITEK Subwoofer Anywhere 640 Transmitter and Receiver
Package content
- 1x Transmitter
- 1x Receiver
- 2x Type C power cable
- 2x Stereo RCA to RCA cable
- 2x Shielded subwoofer cable
- 2x 5V USB-A Power adapter
- 1x Quick guide
Safety instructions
Please read these instructions thoroughly before you use the device and keep them for future reference.
- Only for indoor use.
- Do not expose the product to extremely high or low temperatures, strong light sources or direct sunlight.
- This product is not a toy. Keep out of reach of children.
- Connect the adapter to the mains only after you have verified that the line voltage corresponds to the value specified on the type plates.
- Never connect a power adapter if it’s damaged. In such cases, please contact your supplier.
- Disconnect the AC/DC power adapter from the mains when this device is not in use for a prolonged time.
- Never open the product: the device may contain parts with deadly voltage.
- Repairs or services should only be performed by qualified personnel.
Installation
We recommend that you switch off your equipment before connecting cables in order to prevent any of the devices from being damaged.
- Use the supplied audio cable to connect the Subwoofer Anywhere 640 transmitter to the subwoofer output of your audio system.
- Use the supplied audio cable to connect the Subwoofer Anywhere 640 receiver to the LFE/LINE IN connection on your Active Subwoofer.
- Connect the power adapters [3] with the USB C cable to the Transmitter and Receiver and plug the power adapters into the electrical socket.
- The Transmitter and Receiver will automatically turn on and the white LED will flash slowly. On connection, the LED light will be steady.
- The audio connection is ready to use.
Pairing
When you want to pair an extra receiver, push the power button 2 times quickly on the transmitter. The LED light will flash quickly. Do the same on the new receiver. After a few seconds the LED light will light up steadily and the new receiver is operational.
Standby
When there is no audio input for more than 30 minutes, the Subwoofer Anywhere 640 set will go in standby and the LED light will turn off. When audio input is detected again, the set will wake up in a few seconds and the wireless audio connection will work again.
Power off
Long press the power button to turn off the transmitter and or receiver.
Frequently asked questions (FAQs)
Please go to www.marmitek.com if you have any questions.
Technical specifications
- Audio transfer method Digital
- Transmitter frequency 2.4 GHz
- Frequency channels 26 channels
- RF connection Paired connection (TX and RX)
- Extra receivers up to 10 extra RX
- Supported audio freq. 20 Hz ~ 20 kHz
- Audio delay 12.5 ms (between TX and RX)
- Audio input/output 2x RCA (Stereo L/R + sub)
- Operating range Up to 100 meters clear field, up to 20 meters through walls and ceilings.
- Data transfer speed Up to 2 Mbps, GFSK modulation
- Standby After 30 minutes no audio
- Power 5 VDC USB adapter with USB Type C cable
- Power consumption 0.9 W (transmitter) and 0.3 W (receiver)
- Standby (auto) <0.25 W (TX/RX)
- Standby (power button) < 0.15W (TX) and < 0.1W (RX)
- Dimensions (h x w x d) 907522mm (TX/RX)
- Weight 160 grams
Declaration of Conformity
Hereby, Marmitek BV, declares that this Subwoofer Anywhere 640 set is in compliance with the essential requirements of the 2014/53/EU, 2011/65/EU, and 2009/125/EC: 2019/1782 Directives. Full Declaration of Conformity is available at www.marmitek.com/en/declarations-of- conformity/. More detailed user guides and instructions are available on our website at www.marmitek.com.
20689/20220712 | Subwoofer Anywhere 640 all rights reserved © MARMITEK.
stay connected to marmitek.com.
References
- Marmitek | Specialist for 25 years | Wireless HDMI & audio and Smart Home
- Marmitek | Al 25 jaar specialist in slimme oplossingen
- Declarations of Conformity | Marmitek