ULTIMATE SPEED H589 Open Face Helmet Owner’s Manual

ULTIMATE SPEED H589 Open Face Helmet

Other Model

Important Information

Congratulations!

You have chosen a high-quality product with your purchase. Familiarise yourself with the product before use.
Please read the following instruction manual carefully.
Only use the product as described and for the indicated areas of use. Please store this instruction manual safely. Please hand over all the documentation when passing this product to third parties.

Part designation

1. Visor mechanism
2. Chinstrap with snap-in fastener
3. Ear padding
4. Acoustic padding
5. Inner padding
6. Visor
   

Scope of delivery

The scope of delivery of your helmet consists of:

• Acoustic padding
• Helmet bag
• Instruction manual

Important information

This helmet has been designed for motorcycling and manufactured according to the latest technology. Despite the highest safety standards, injuries can still occur in the event of serious accidents. In some cases, the impact may be so strong that the helmet does not effectively protect the wearer from head injuries.

In order to provide adequate protection, this helmet must fit snugly and be securely fastened. Any helmet that has been subjected to an intense impact must be replaced. We guarantee that this product is free from manufacturing and material defects. The warranty claim does not apply to abrasion or normal wear and tear and is void in the event of improper handling.

For France, it is mandatory to have four reflector stickers on the helmet. These reflector stickers are included with your helmet. Apply the stickers to both sides as well as to the front and back of the helmet.

Instruction manual

Safety instructions

• Warning!
  The helmet must fit tightly and the chinstrap must be firmly closed.

• Make sure that the air circulation is not restricted.

• Make sure that the visor is always clean and without any scratches. Damaged visors must be replaced immediately. Up to five years after the date of purchase, you can reorder spare visors from the mentioned service address, visor number:
  HS-05.

• No modifications may be made to the helmet, its structure or individual components.

• The helmet must not be painted or have stickers or labels attached to it.

• The helmet is designed to protect the head in the event of an impact. After just a single (even light) impact, this protection is no longer guaranteed. After an accident, the helmet must therefore be replaced immediately even if it has no visible damage.

• The helmet must not be transported hanging from the handlebars or any other part of the machine. It is also essential to keep it away from heated parts (e.g. exhaust).

• Never use petroleum-based solvents or abrasive cleaners to clean the helmet, neither on the outside nor on the inside.
  Always use a pH-neutral detergent diluted in clear water. Rub gently with a soft cloth. Then wipe dry with a lint-free cloth. The padding can be cleaned using a little bit of soap and a soft brush.

• Use only original spare parts for your helmet.

Product features

ECE-R 22.06

Homologation

This helmet meets the ECE-R 22.06 standard and is homologated according to it.

The ECE-R 22.06 standard contains uniform conditions for the approval of protective helmets and their visors for drivers and passengers of motorcycles and mopeds.

The basis for these tests are the so-called ECE regulations of the United Nations Economic Commission for Europe.

Essential tests of the ECE regulation 22.06

• Impact absorption
• Dynamic test of the retention system
• Testing the field of vision
• Structural strength
• Retention test (detaching test)
• Chinstrap and lock testing
• Shear test for outer edges
• Test of the friction behaviour of the outer shell
• Visor testing (mechanical and optical properties)
• Chin impact, testing of the chin part attenuation

Inner padding with Coolmax® inserts

Coolmax® from INVISTA is a high-performance fabric fibre that supports the wearer during sports activities. Based on the patented DuPont fibre technology, Coolmax® transports moisture from the body to the fabric surface where it dries faster than any other fabric. The specially developed fibres from INVISTA used for Coolmax® fabrics transport moisture away from the body to the surface of the fabric where it can evaporate quickly.
At the same time, the uniquely shaped fibres provide maximum breathability even when wet. In addition, the breathability improves the thermoregulatory effect.
In this product, ear and forehead pads are equipped with Coolmax®.

HeiQ Pure

Textile freshness
Experience the feeling of lasting freshness thanks to the power of silver which keeps you odour-free throughout the day.
The inner lining of the helmet contains a biocidal agent (HeiQ Pure) for antibacterial equipment of the inner lining. Active agent:
Silver Chloride

| Impact-resistant ABS outer shell
---|---
| Visor with anti-scratch coating
| Suitable for eye-glass wearers
| Safety snap-in fastener

Operating and assembly instructions

Snap-in fastening system (Fig. B)

The snap-in fastener allows individual and quick fine adjustment of the chinstrap.
Squeeze the snap-in fastener until the helmet fits comfortably but firmly.
The sliding buckle allows the excess chinstrap to be attached or secured.

Ear padding (Fig. C)

Each ear pad (3) is fastened in the helmet by means of three snaps. You can easily pull out the pads.
When fastening the ear pads in the helmet, each snap must audibly click into place.

Acoustic padding (Fig. D)

The acoustic padding (4) serves to reduce noise, especially when driving at high speeds.
Press the acoustic padding into the cavity of the cheek pads. The acoustic padding side equipped with Velcro® faces the helmet shell.

Changing the visor (Fig. E)

Removing the visor
Slide the visor to the lowest position.
Start at one side of the visor and pull it out of the attachment. Then pull out the visor completely on the other side.

Inserting the visor

Insert one side of the visor into the designated opening on the helmet until the visor locks into place. Repeat this step on the other side as well.

Choosing the right helmet size

• Measure the circumference of your head and choose the size of the helmet accordingly. Try several helmets before making a decision. With the helmet on, the skin on your temples will ideally also move.
• Make sure that, even without the chinstrap being tightened, the helmet does not have much freedom of movement on the head.
• For a secure fit, the chinstrap must be closed tightly. It fits correctly if you find it difficult to slide your fingers under the chinstrap. However, you still need to be able to breathe, swallow and turn your head comfortably.
• Convince yourself that the helmet was tested according to the latest ECE standard.

Size table

Size| Head size
S| 55-56cm
M| 57-58cm
L| 59-60cm
XL| 61cm

Maintenance and care

Regular maintenance and care contributes to the safety and preservation of the helmet. Cleaning the helmet

• Never use petroleum-based solvents or abrasive cleaners to clean the helmet, neither on the outside nor on the inside.
• Always use a pH-neutral detergent diluted in clear water. Rub gently with a soft cloth. Then wipe dry with a lint-free cloth.

Visor care and cleaning

• After use, wipe off soiling (e.g. insects, sand, dust etc.) with a soft, damp cloth and then wipe off with a soft, dry cloth.
• After use in wet and humid conditions, the visor should always be wiped off with a dry, soft cloth.
• Never use petroleum-based solvents or abrasive cleaners when cleaning the helmet.

Cleaning the ear and acoustic padding

• Hand wash below 30 °C.
• Allow to dry at room temperature.
• Avoid sources of heat.
• Store in dry, ventilated areas when not in use.
  

Storage

Store the helmet in a dry and well-ventilated place at room temperature when not in use.
Avoid sources of heat.
Do not expose the product to unnecessarily intense heat, e.g. in the car at high outside temperatures.

Notes on disposal

Dispose of the product and packaging materials in accordance with current local regulations. Keep packaging materials, such as foil bags, out of the reach of children. Store packaging material out of the reach of small children.
Dispose of the product and packaging in an environmentally friendly manner.
The recycling code is used to identify various materials for return to the recycling loop.
The code consists of the recycling symbol – intended to reflect the recycling loop – and a number identifying the material.

Explanation of symbols

| Date of manufacture (month/year)
---|---
| Read the user manual

SPEQ GmbH warranty

Dear Customer,
The product was produced with great care and under continuous quality control. Speq GmbH gives private end customers a three-year guarantee on this product from the date of purchase (guarantee period) in accordance with the following provisions.

Warranty conditions

The warranty period starts from the date of purchase. Please keep the original receipt in a safe place. This is required as proof of purchase. If a material or manufacturing defect occurs
within three years from the date of purchase of this product, we will – at our option – repair or replace the product for you free of charge or refund the purchase price. This warranty service requires that within the three-year period, the defective device and the proof of purchase (receipt) are submitted and briefly described in writing what the defect is and when it occurred. If the defect is covered by our warranty, you will receive the repaired or a new product back. Repair or replacement of the product does not start a new warranty period.

Warranty period and statutory claims for defects

The warranty period is not extended by the warranty. This also applies to replaced and repaired parts. Any damage and defects already present at the time of purchase must be reported immediately after unpacking. Repairs required after the expiration of the warranty period are subject to a charge.

Warranty scope

The device was carefully produced according to strict quality guidelines and conscientiously tested before delivery. Warranty coverage applies to defects in materials or workmanship.
This warranty does not cover product parts that are subject to normal wear and tear and can therefore be considered wear parts or for damage to fragile parts, e.g. switches, batteries or that are made of glass. This warranty is void if the product is damaged, improperly used or maintained. For proper use of the product, all the instructions given in the operating manual must be strictly observed. Uses and actions advised against or warned against in the operating instructions must be avoided at all costs. The product is intended for private use only and not for commercial use. Abusive and improper handling, use of force and interventions not carried out by our authorized service branch will void the warranty.

Handling in case of warranty

In order to ensure a quick processing of your request, please follow the following instructions:

• For all inquiries, please have the receipt and item number (IAN) ready as proof of purchase.
• Please refer to the type plate on the product, an engraving on the product, the title page of your manual (bottom left) or the sticker on the back or bottom of the product for the article number.
• If functional errors or other defects occur, first contact the service department named below by telephone or e-mail..
• If the product is found to be defective, you can send it free of charge to the service address provided by you, enclosing the receipt and stating what the defect is and when it occurred.

On www.lidl-service.com you can download these and many more manuals, product videos and installation software. This QR code will take you directly to the Lidl service page (www.lidl-service.com) and by entering the item number (IAN) you can open your user manual.

Service address

SPEQ GmbH
Tannbachstr. 10
73635 Steinenberg
Germany
Email: service@speq.de
Service-Hotline: 00800 30 777 999
(toll free)
Please call us before sending the product
8:00 h – 17:00 h
Model: H589
IAN: 434910_2304, 434911_2304,
434912_2304, 434916_2304
Service Adresse:
SPEQ GmbH
Tannbachstr. 10
D-73635 Steinenberg
Hotline: 00800 30 777 999
Email: service@speq.de

References

• de/
• de/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>