Seco Larm SL-1301-SAQ-A LED Strobe Lights Instruction Manual

: July 26, 2024
: SECO-LARM

Table of Contents

Seco Larm SL-1301-SAQ-A LED Strobe Lights
Product Usage Instructions
ENFORCER LED Strobe Lights
Parts List
Specifications
of flash patterns| 1*| 8
Dimensions
Overview
Installation
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Seco Larm SL-1301-SAQ-A LED Strobe Lights

Specifications:

Model Vertical LED strips Total number of LEDs
SL-1301-EAQ 0 6
SL-1301-BAQ 5 32
SL-1301-SAQ 10 54
Operating voltage: 9~15 VDC, 9~24 VAC/VDC
Operating life : Over 50,000 hours (over 5.7 years)
IP rating (when installed properly): IP64, IP66, IP55
Dimensions: Top View – 315/16 (100mm), Front View – 31/8 (79mm), Bottom View – 21/8 (54mm), Side View – 213/16 (71mm)

Product Usage Instructions

Overview:

Ground wire (black), Power wire (red), Circuit board LEDs, LED strips, BAT., ON OFF ON / OFF, 9-Volt battery clip (under circuit board), SP ON / OFF, Backup battery jumper (default off), Siren jumper (default off), Strobe speed control.

Installation:

Before starting, please read this manual carefully and keep it for future reference.
Remove the lens and mount the LED strobe light.

FAQ

Q: What is the operating voltage of the LED strobe lights?
- A: The operating voltage is 9~15 VDC and 9~24 VAC/VDC.
Q: What is the IP rating of the LED strobe lights?
- A: The IP rating varies based on the model: IP64, IP66, or IP55 when installed properly.
Q: Can the LED strobe lights be used continuously with a backup battery?
- A: Yes, the BAQ and SAQ series have a backup battery function available for continuous lighting applications.

Color / LEDs	6 LED	32 LED	54 LED
Red	SL-1301-EAQ/R	SL-1301-BAQ/R	SL-1301-SAQ/R*
Blue	SL-1301-EAQ/B	SL-1301-BAQ/B	SL-1301-SAQ/B*
Amber	SL-1301-EAQ/A	SL-1301-BAQ/A	SL-1301-SAQ/A*
Clear	SL-1301-EAQ/C	SL-1301-BAQ/C	SL-1301-SAQ/C*
Green	SL-1301-EAQ/G	SL-1301-BAQ/G	SL-1301-SAQ/G*

All Models:

Utilizes high-intensity LEDs
Operating life of over 50,000 hours (over 5.7 years)
Same size as the SL-126Q strobe light
Simple 2-wire installation
5 lens colors available for each model
Weather resistant
High-impact resistant case
High-impact and heat-resistant lens
Reverse polarity protection
Visible in all directions

BAQ series includes all features of the EAQ plus:

5 Vertical LED strips (32 LEDs total) increase visibility from various directions
8 Different flashing patterns and adjustable duty cycle
Adjustable flashing speed
Backup battery available for continuous lighting applications

SAQ series includes all features of the BAQ plus:

10 Vertical LED strips (54 LEDs total)
Built-in 100dB siren (programmable)

ENFORCER LED Strobe Lights

Introduction:

ENFORCER LED Strobe Lights provide all the functions of a regular strobe light and much more. Each has an operating life of 50,000 hours—over 160 times that of a regular strobe light. No more bulbs to replace! There are three models—with 6~54 LEDs. The BAQ series and SAQ series include a unique placement of LEDs making the light more visible from various directions, a 9V backup battery option making them ideal for continuous lighting applications, and 8 selectable strobe patterns, adjustable duty cycle, and adjustable strobe speed. The SAQ series also includes a built-in 100db siren.

Parts List

1x LED Strobe Light
1x Adhesive gasket*
2x Mounting Screw with “O” rings
1x Manual

SL-1301-EAQ only

Specifications

Model	SL-1301-EAQ	SL-1301-BAQ	SL-1301-SAQ
Vertical LED strips	0	5	10
Total number of LEDs	6	32	54
Operating voltage	9~15 VDC	9~24 VAC/VDC

Current drain @12VDC (max)

| Rotate clockwise| N/A| 70mA| 90mA†
Strobe| 150mA| 350mA| 550mA†
Steady ON| N/A| 350mA| 550mA†
Flash with progressive ON| N/A| 350mA| 550mA†
Rotate back and forth| N/A| 70mA| 90mA†
Flash with progressive ON/OFF| N/A| 350mA| 550mA†
Adjustable flash pattern| No| Yes

of flash patterns| 1*| 8

SL-1301-EAQ series has strobe only

With siren enabled

9VDC battery not included

estimated, depending on mode

Dimensions

Overview

Installation

Before starting, please read this manual carefully and keep it for future reference.
Be sure to use the LED strobe light within the given electrical limits.
Decide where the LED strobe light is to be mounted. Use a pencil to mark the location of the two mounting screws.
Drill a hole through the wall or surface where the LED strobe light is to be mounted. Run the ground (black) and power (red) wires through the wall.
Note : For surface wiring applications, remove the thinned-out slot with a pair of pliers.
Connect the wires to their respective locations on an alarm control panel or other security panel.
Remove the lens and mount the LED strobe light (with adhesive gasket for SL-1301-EAQ) to the surface using the two included mounting screws with rubber “O” rings. If screws are fastened too tightly, the “O” rings will be damaged. (SL-1301-EAQ series skip to step 10)
Select the flash pattern and flash duty cycle using the DIP Switch (see back page for details) and adjust the speed using the strobe speed control (clockwise to increase, counterclockwise to decrease).
Set the siren (SL-1301-SAQ only) to on or off using the siren jumper.
If needed, install a backup battery. (See below.)
Replace lens. If lens is fastened too tightly, the “O” ring will be damaged.

Backup Battery (SL-1301 BAQ/SL-1301-SAQ series only)

For continuous lighting applications, the backup battery will power the LED strobe light in the event of a power loss.

Use a screwdriver to loosen the circuit board screws.
Carefully remove and flip the circuit board. The battery holder is attached at the back side of the circuit board.
Connect a 9-Volt battery to the battery connector.
Replace circuit board and circuit board screws.
Turn the backup battery on via the backup battery jumper.

Troubleshooting

The LED strobe light does not turn on

Check the LED strobe light’s power source

The LED strobe light does not flash correctly

Disconnect power, configure the correct flash pattern, and reconnect power

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if the damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

Configuring Flash Pattern and Duty Cycle (SL-1301-BAQ/SL-1301-SAQ series only):

IMPORTANT: Before changing the DIP switch, disconnect the power. Reconnect power after switches are set.
Users may customize both flash patterns and duty cycle (flash patterns 1, 2, and 5 only). The “One-Eighth Duty Cycle” produces a sharper “strobe” effect more like traditional strobe lights. DIP Switch #4 controls the duty cycle for supported flash patterns. Visit www.seco-larm.com for a demonstration of flash patterns/duty cycle.

California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved.

SECO-LARM® U.S.A., Inc.