Monogram ZKW72BV 72 Inch Brass Top Plates Installation Guide
- July 25, 2024
- MONOGRAM
Table of Contents
Monogram ZKW72BV 72 Inch Brass Top Plates
Specifications
- Designated Width: 30, 36, 60, 66, 72 inches
- Actual Width:
- 30: 29-1/2 inches
- 36: 35-1/2 inches
- 60: 59-1/4 inches
- 66: 65-1/4 inches
- 72: 71-1/4 inches
Product Usage Instructions
Read the instructions completely and carefully. Ensure the appliance is secured to prevent tipping forward, especially when doors are open.
Prepare the column(s) for installation following the provided Column Installation Instructions. Ensure proper unification brackets are in place.
- Install one Upper Anti-Tip Bracket to each side of the cabinet enclosure.
- Use three screws per bracket; drill 5/32 holes to aid installation.
- Ensure all three screws in each bracket are tight before proceeding.
- If installing into drywall, use correctly sized drywall anchors.
- Confirm proper unification of columns with the installation of brackets.
- Loosen the indicated screws on top of the columns.
- Place top plate keyhole slots over the screw heads on each side.
- Tighten all four screws and ensure they are secure.
- Loosen the indicated screws on the top of the column.
- Place top plate keyhole slots over the screw heads on each side.
- Tighten all four screws and ensure they are secure.
FAQ
- Q: How should I ensure the appliance is secure to prevent tipping?
- A: Use the provided Upper Anti-Tip Brackets and follow the installation instructions carefully to secure the appliance properly.
- Q: What should I do if I am installing into drywall?
- A: Use correctly sized drywall anchors to ensure a secure installation.
- Q: Do I need to follow specific instructions for Dual Integrated Installation?
- A: Yes, ensure proper unification of columns and follow the step-by-step instructions provided for Dual Integrated Installation.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
- Note to Installer – Be sure to leave these instructions with the Consumer.
- Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
WARNING Tip Over Hazard
These appliances are top-heavy, especially with any doors open, and must be
secured to prevent tipping forward which could result in death or serious
injury.
PRODUCT DIMENSIONS
| Designated Width | Actual Width |
|---|---|
| 30 | 29-1/2” |
| 36 | 35-1/2” |
| 60 | 59-1/4” |
| 66 | 65-1/4” |
| 72 | 71-1/4” |
ADDITIONAL PARTS PROVIDED
Prepare Column(s) for Installation as per Column Installation Instructions
WARNING Tip Over Hazard
These appliances are top-heavy, especially with any doors open, and must be
secured to prevent tipping forward which could result in death or serious
injury.
Read and follow the entire installation instructions for securing the
appliance with the anti-tip system.
After installing the Column Anti-Tip Brackets as per the Column Installation
Instructions, follow these instructions to install the Upper Anti-Tip
Brackets.
This is not a replacement for proper column installation, be sure to follow
all column installation instructions carefully.
- Install one Upper Anti-Tip Bracket to each side of the cabinet enclosure. Use three screws per bracket, drill 5/32” holes to aid installation.
- See diagram at right for location.
- Be sure to install all three screws in each Upper Anti-Tip Bracket and confirm they are tight before proceeding.
- If installing into drywall, use correctly sized drywall anchors.
For Dual Integrated Installation
- Continue Column installation up to the point of unification, right before pushing the Column into the opening.
- Go to Page 4 of these Installation Instructions to install the Top Plate.
- Return to the Column Installation Instructions to complete the installation.
For Single Integrated Installation
- Continue Column installation up to the point of unification, right before pushing the Column into the opening.
- Go to Page 5 of these Installation Instructions to install the Top Plate.
- Return to the Column Installation Instructions to complete the installation.
Installation Instructions
For Dual Integrated Installation
STEP 1
Confirm the columns have been properly unified with the installation of all
unification brackets.
STEP 2
Loosen the 4 indicated screws on the top of the columns.
STEP 3
Place top plate keyhole slots over the screw heads on each side.
STEP 4
STEP 5
- Confirm all screws are tight.
- Return to the column installation instructions.
For Single Integrated Installation
STEP 1
Loosen the 4 indicated screws on the top of the column
STEP 2
Place top plate keyhole slots over the screw heads on each side.
STEP 3
STEP 4
- Confirm all screws are tight.
- Return to the column installation instructions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>