Monogram Appliances ZKMV Integrated Bottom Freezer Unification Heater Kit Instruction Manual
- June 1, 2024
- Monogram Appliances
Table of Contents
Monogram Appliances ZKMV Integrated Bottom Freezer Unification Heater Kit
Product Information
Specifications:
- Product Name: ZKMV Heater Unification Kit
- Compatibility: Designed for installation of Heater Unification components for 2 Integrated Bottom Freezer Single Door units side by side
- Components Included: Adhesive Heater, Transformer, Front Mullion Trim, Trim Bracket, Top Unification Bracket, Bottom Back Unification Bracket, Bottom Front Unification Bracket, Screws, Wire Clips
- Tools Required: 1/4 and 3/8 driver/sockets, #2 Phillips screwdriver, Rubbing alcohol
Product Usage Instructions
Unpacking and Preparation:
Unpack the ZKMV Heater Unification Kit and ensure all listed components are included.
Ensure the unit is unplugged and turned off during the installation process.
Heater Installation:
- Place the right-hand unit in front of the installation opening.
- Install the adhesive heater on the outside of the unit’s left side, below the case top, ensuring it is centered front to back.
- Clean the installation area using rubbing alcohol for proper clip adhesion.
- Securely install the transformer onto the case top and connect it to the heater connector and panel control.
- Verify that the master switch is on.
- Assemble the cover top back in place.
- Connect the heater connector to the transformer connector with blue and yellow wires.
Safety Precautions:
Always be cautious of electrical shock hazards. Ensure proper grounding and follow safety instructions provided in the manual.
Frequently Asked Questions
Q: Can I install the heater on both sides of the unit?
A: No, the heater installation is available only on the left side of compatible models as per the manufacturer’s guidelines for safety reasons.
Q: What should I do if a component is missing from the kit?
A: If any component is missing from the ZKMV Heater Unification Kit, please contact customer support for assistance in obtaining the necessary part.
Before you begin – Read these instructions completely and carefully.
WARNING
Electrical Shock Hazard.
To avoid the risk of electric shock, make sure the power cord is not plugged
into the wall outlet.
This kit provides for the installation of the Heater Unification components when installing 2 Integrated Bottom Freezer Single Door units side by side.
Parts List:
- Adhesive Heater
- Transformer
- Front Mullion Trim
- Trim Bracket
- Top Unification Bracket
- Bottom Back Unification Bracket Bottom Front Unification Bracket
- 3 1/4” Hex Head 8-18 5/8” Long Screws
- 5 1/4” Hex Head 8-32 5/8” Long Screws
- 5 3/8” Hex Head 1/4-20 1/2” Long Screws
- 4 wire clips
Tools and Materials Required:
1/4” and 3/8” driver / sockets #2 Phillips screwdriver Rubbing alcohol
Instructions for this kit are also included in the full installation
instructions included with the unit.
Unpack the heater Unification Kit (ZKMV) and make sure all of the components
on the list are included.
Installation Instructions
HEATER INSTALLATION
-
Unpack the heater Unification Kit (ZKMV) and make sure all of the components on the list are included.
-
Make sure unit remains unplugged and off during heater installation.
NOTE: Ensure the heater connector cord is toward the top of the unit when installed. -
Place the right hand unit in front of the installation opening in a way that the unit is in front of the intended installed location.
-
Install adhesive heater on the outside of the unit to the left side of the case. Install heater 4” below the case top. Heater should be centered front to back on the metal case.
-
Use clips to adhere loose wire tightly to side of case as shown. Clean the side using rubbing alcohol to ensure proper clip adhesion.
NOTE: The heater installation is available only on the left side of compatible models.
WARNING
Electrical Shock Hazard.
To avoid the risk of electric shock, make sure to re-install the ground screw
after changing the power cord.
Install the transformer into the case top assembly:
- Remove cover top by removing eight #8 hex screws and keep aside for assembling back the cover top.
- Place the transformer provided in ZKMV kit onto the case top. Secure transformer with (1/4”) hex screw to case top in existing hole at the rear right side of the top control housing.
- Connect the 2 pin transformer connector to the heater connector and 3 pin connector to panel control, make sure locking tabs are engaged.
- NOTE: Verify the master switch is on.
- Assemble the cover top with screws save from previous step.
Enclosure assembly above is shown with cover removed
UNIFICATION BRACKET INSTALLATION
Remove the two front lower access covers by removing the four ¼” hex head screws. ( 2 per unit)
On the side of the access cover that will face the middle of the installation, drive two 1/4″ hex head screws. These screws will enhance attachment of mullion trim. Repeat on the second access cover.
Set access covers aside to be reinstalled after bottom front bracket is installed.
TOP UNIFICATION
- Loosen the middle two screws, remove the two rear screws.
- Assemble the bracket to the middle screws and reassemble the rear screws.
- Tighten screws to tie units together.
BOTTOM BACK UNIFICATION
- Loosen the two bottom screws of rear access covers of both units and remove the top screws.
- Hang the unification bracket to the bottom screws and reassemble the screws at the top.
- Tighten screws to unify both refrigerators.
BOTTOM FRONT UNIFICATION
- Install the bottom front unification bracket using a 3/8” driver (4 screws).
- Make sure the two screws you added to the side of the front access cover face each other when reinstalling lower access covers.
- Reinstall the two front lower grille covers by securing with the four ¼” hex head screws.
- After joining unit together, plug power cords into outlet for both units.
FINAL EXTERNAL UNIT PREPERATION
WARNING
Tip Over Hazard.
These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping forward which could result in death or serious injury. Read and follow the entire installation instructions for securing the appliance with the anti-tip system before installing kit.
Mullion Trim Installation
- Open all doors and drawers.
- Align top of Mullion Trim with top of control panels.
- Install mullion trim between the two units by pushing the dart in the area between the units.
- Ensure trim is fully seated against case. Adjust if necessary.
- Open both water filter access doors to 90°.
- Snap the trim bracket between the water filter access enclosures above displays.
TOE KICK INSTALLATION
-
Create a custom toe kick or purchase Stainless Steel Toe kick 2KK72R (Standard Install) or 2KN72V (Integrated Install).
-
Custom toe kicks are to be provided by the customer.
-
Remove the toe kick magnets from the front access covers. These will be used for the custom toe kicks only.
-
Back surface of the custom toe kick must be clean and free of foreign material.
-
Center magnet vertically and horizontally
-
Adhere magnets to the back side of the custom toe kick.
-
Position toe kick on bottom portion of front access covers.
-
FOLLOW ALL INSTALLATION INSTRUCTIONS PROVIDED WITH THE APPLIANCE TO COMPLETE THE DIAI INSTALLATION
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>