domli D2 Premium Dual Motor Black Standing Desk with Oak Solid Wood Desktop Installation Guide

domli D2 Premium Dual Motor Black Standing Desk with Oak Solid Wood

Desktop

Product Specifications

• Model: Electric Rising Leg-Set D2
• Weight Capacity (including desktop): 100 kg
• Weight Capacity (per leg): 50 kg

Product Usage Instructions

Installation Guide

Safety First!

1. Use caution when handling heavy or bulky components to prevent injury or damage to yourself and the product.

2. Always wear protective equipment, such as gloves or safety glasses, when using power tools to avoid accidents.

3. Do not over-tighten screws or bolts, as this can damage the components or compromise the stability of the product.

4. Please follow the provided instructions carefully to ensure proper assembly and use of the product.

5. Keep small parts away from children or pets, as they can be a choking hazard.

6. Inspect the product for any defects or dam- ages before assembly, and contact us if you notice any issues.

7. Please do not modify the product or use it for any purpose other than its intended use.

8. Use caution when working with sharp tools or edges, and keep them away from children and pets.

9. If you are uncertain about any aspect of the assembly process, seek assistance from a professional or contact us for further assistance.

10. Do not sit or stand on the product.

11. This product is not intended to support people or heavy objects. Avoid placing excessive weight to prevent damage and instability. MAX Lifting Weight (including desktop) 100Kg.

CAUTION:
SAFETY AND WARNINGS

• Inappropriate use of this product may cause property or bodily injury. Make sure that children, pets, etc. stay away from the product when the desk is in operation.
• Check the surroundings on all sides before using the desk. Make sure the desk does not touch the wall.
• Please unplug the power supply during lightning and when the product is not in use for a long time.
• Make sure NO obstacles are in the desk’s path and no obstacles higher than 500 mm under the table. Body parts and property can be crushed if trapped between an immobile obstacle and the desk’s range of motion.
• Keep the work environment temperature at 0-40 °C. And keep goods away from corrosive gases, liquids, and dusty objects.
• Ensure the length of power cords is accounted for when operating the desk. Monitors, computers, speakers, and anything with a cord that is not long enough for the desk’s range of motion could be pulled down or have its wires broken. Items pulled off the desk may cause other items to fall.
• It is strictly forbidden to disassemble the product without permission, in order to prevent the product from malfunctioning and electronic products from causing harm to the human body.
• Please provide this operation to any users, installers, or support personnel operating the product. Read relevant operating instructions before using.The company does not take any responsibility for product damage and human body injury caused by the abnormal operations.

USAGE
This desk height is adjustable so that it can be positioned at the most ergonomically suitable height. These desks are designed only for the purposes included in this manual. They should not be used in environments with high humidity or dampness. Any other use is at the user’s risk. Do not move around, crawl or lie under the desk frame. Do not sit or stand on the desk frame.

Children should never use the desk unless they are supervised by adults.

• Liability: Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused by improper use handling of the desk frame other than that which is described in this operation manual.

SETUP AND INSTALLATION
Once the desk has been assembled, adjust the feet so that the desk is level and does not shift its position. After this, connect the desk to the 11 0v or 240v outlet and the desk is ready for use. Check that no cables can get jammed. Choose a placement for the desk that’s a safe distance from window frames, radiators, furniture, etc. So that people do not get stuck or trapped by the desk. Do not place any objects that are taller than 50cm(20″) underneath the desk. After it has been assembled, when moving the desk, DO NOT lift the desk by the desktop. Lifting this way can stress the fasteners connecting the desk base to the desktop. Lower the desk completely and lift the desk by grabbing the top of the desk base or by removing the desktop first.

Part List:

• Lift Column x 2
• Crossbar x 2

Tool Required:

• Tape Measure
  • 3mm Allen Wrench

Components

Hardware

ASSEMBLY INSTRUCTIONS

1. Pull out the frame

   • Lay out all components and hardware to ensure that you have all the parts.
   • Lay the Crossbar End 1 and 2 out flat on the floor, slide the frame out evenly from both sides.
   • SIide crossbar center rails out of Crossbar ends.

2. Attach legs to Frame

   • Align the crossbar end to the lifting column, Insert the MSX 12 mm screws(A),and tighten it.
   • Repeat for the other side. Avoid over-tightening the screws to damage the product.

3. Attach Side Bracket

   • Line up the two holes on the side bracket with the Crossbar End . Insert two M6X8 mm screws(C)and tighten it.
   • Attach the washers on the side bracket.
   • Repeat for the other side.

4. Attach Foot

   • Attach leveling studs to the foot.
   • Align the foot with the lift column, and insert four M6X 16 mm(B) into the holes under the feet, tighten it.
   • Repeat for the other side. Avoid over-tightening the screws to damage the product.

5. Merge the frame
   Slide Crossbar Center Rails back into Crossbar Ends. Ensure the slots of the Crossbar Center Rails are facing inward.

6. Attach Frame Set to tabletop

   • Place the bottom of the tabletop on the underside of the installed frame, stretch the frame. It is recommended that the frame side boards at both ends be 50mm away from the edge of the table board, and fasten with MSX 18 mm screws(D).
   • Use M8X6 mm screws(F) to fasten the crossbar ends and crossbar center rails.The length of the frame can be adjusted by lifting the two side brackets. The adjustable range is 1010~1750 mm, which can be used for tables of different widths. Avoid over-tightening the screws to damage the product.

7. Attach Control Box & Handset

8. Insert the Control Box(?} controller into the crossbar.

9. Attach the Handset(8} to the tabletop plate with M4 X 12mm(E} screws.

10. Attach Connect Cables

    • Connect the line pulled from lifting column 1 to Control Box(7}M1. Connect the line pulled from the other lifting column to Control Box(7}M2.
    • Connect the outgoing lines from the Handset (8) to the Control Box(7} HS port.
    • Connect power cable (9) to Control Box(?} AC port.

11. Put desk Upright and Connect Power Cord to the Power Supply

    • With the desk at its lowest height,turn the assembled desk right-side up with the help of at least two people.
    • Plug the Power Cord(9)into a 240v outlet. NOTE: Grab the desk Frame (not the desktop and turn the desk right-side up. Use at least two people. CAUTION , the desk is very heavy!

12. Adjust Leveling Studs
    If necessary, adjust the leveling studs to level the desk. Unscrew to increase height, and screw in to decrease height.

13. Initialize

14. Press the” V II button until the desk reaches the lowest position.

15. Press” V” for 5 seconds until there is a beep sound heard, and the desk reset is successful. Your desk is ready to use.

You must complete this initialization step or your desktop will NOT function properly. Press the down arrow until the desktop moves slightly upwards!

Operating Manual

• RESET
  Reset after the initial installation or power failure

  • When the system is abnormal, or the hand controller displays “RST” ” the lifting table needs to be reset.
  • Press and hold the ” v ” key to lower the desk to the lowest height, release, and press the ” v ” key until the display shows RST a beep sound is heard, and the display shows “60” (three-section column) or “70” (two-section column).
  • Release the ” v ” button, the reset is successful at this time, and the desk can be used normally.

Note: During all reset processes, the anti-collision system will fail at this time. Please ensure that there are no obstacles near the table during the reset process to prevent dan er.

• UP and DOWN

  • Press the “/\” key to adjust the ascending height freely.
  • Press ” V ” key to adjust the descending height freely.

• Location storage and memory operation
  By memorizing the position setting, you can easily reach the position you want with one dick. (Two key switches do not have this function)

  • Ascend or descend to your desired height.
  • Press and hold the M key until show “S-11
  • Press the “1” key to complete the setting of the first memory. (“2” key and “3 key” are the same as above)

• Anti-collision protection
  Before using this product, check for obstades and remove them in advance.

  • When the tabletop encounters an obstacle in the process of ascending or descending, it will immediately rise or fall in the opposite direction.
  • The tabletop runs in reverse for some distance and works normally after removing the obstacle.

• Minimum and maximum limit setting
  Do not set this function unless necessary.

  • Hold the “M” +”/\”button at the corresponding height for 5 seconds, then you will hear the buzzer sound, indicating that the lowest position is successfully stored.
  • Hold down the “M” + “/\” button for 5 seconds, at this time you will hear the buzzer sound, indicating that the lowest position storage is canceled.
  • Hold the “M “+ “V” button for 5 seconds, you will hear the buzzer sound, indicating that the highest position is stored successfully.
  • Hold down the “M” + “V” button for 5 seconds, you will hear the buzzer sound, indicating that the highest position storage is canceled .

Note: By applying this function to adjust the movement limit position of the table top, once set, the new lowest position and highest position will be archived. Buzzer sound, indicating that the highest position storage is canceled.

Locking and unlocking child locks

• Locking: Hold “/\ “+” V” for 5 seconds at the same time, when the digital tube shows “Loe”, this time indicates that the system has been locked. Cannot do lifting operation on the system.
• Unlock: Hold “/\ “+” V” for 5 seconds at the same time, when the digital tube is displayed from Loe to the normal digital display, indicating that the system has been unlocked.

Internal parameters and installation distance settings

• By long pressing the M key for 10 seconds, you can enter the setup interface, showing the x-y simultaneously y flashing, where x is the parameter group, and the parameter value corresponding toy . The parameter group can be switched by pressing “SET” and the value of the parameter can be changed by pressing “up” or “down “. Set the parameters by pressing the “M” key for 10 seconds to return to the running interface.
• The following parameters can be set:
  • “1-y” “y” 0 means CM display,”y”1 means INCH display;
  • “2-y” “y” means the gyroscope has the resistance to stop accuracy,O means off, 1 is the most sensitive and 8 is the most insensitive. ;
  • “3-y” “y” means up-current resistance stop accuracy,O means off, 1 is most sensitive and 8 is most insensitive.
  • “4-y” “y” means the down current meets the stop precision,O means the off, 1 is the most sensitive and 4 is the least sensitive.
  • “yyy” “yyy” three digits are displayed at the same time,it means the installation distance, the unit is cm.

Automatic testing
Specific hand controller, support system run for 2 min stop for 18 min automatic test, the travel of test is between M1 storage location to M2 storage location. When auto test mode, the system will run back and forth for 2 min between M 1-M2, then stop for 18 min, infinite loop.

• Access Hold down the “M”+” /\ “+” V” button for 2 seconds, and all decimal points in the digital tube are displayed, indicating automatic test mode, and exiting automatic mode is also holding down the “M”+” /\ “+” V” button for 2 seconds.

Error messages on the handset’s display

Installation of wire shield

Tool:

Accessory:

Part List:

Installation Steps:

• Step 1: Install Lift Columns and Crossbars as per Part List.
• Step 2: Attach Accessory A and B according to the Installation Guide.

Freq uently Asked Questions

Q: Can this product support heavy objects?
A: The product is not intended to support heavy objects. It has a weight capacity of 50 kg per leg and 100 kg including the desktop.

Q: What should I do if there are defects in the product?
A: Inspect the product before assembly. If you find any defects, contact customer support for assistance.

Q: Is it safe for children and pets?
A: Keep small parts away from children and pets to avoid choking hazards. Additionally, avoid sharp edges and ensure stability to prevent accidents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>