aranet TDSBOA03 Data Logger Gateway User Guide

aranet TDSBOA03 Data Logger Gateway

Specifications

• Model: Aranet PRO Plus Base Station
• Manufactured in: Latvia, EU
• WiFi SSID: Aranet-C20a47
• WiFi IP: 192.168.206.100
• ETH IP: 192.168.205.100
• ETH MAC Address: C493003034E4
• Power: IEEE 802.3af PoE
• Username: root
• Password: FhTdwPN7fg

FAQs

• Q: Do I need a PoE injector to power up the base station?
  • A: Yes, you will need either a Power over Ethernet (PoE) injector or a device that supports PoE to power up the base station. You can order a PoE injector from the Aranet shop.
• Q: How do I reset the network settings and password of the base station?
  • A: To reset the network settings and the root user password, press and hold the Network Reset Button for at least 5 seconds.

What`s in the box

• Aranet Base station
• Ethernet cable

Essential for successful installation

• To power up the base station, you’ll need either a Power over Ethernet (PoE) injector or a device that supports PoE. You can order a PoE injector from the Aranet shop.

Base station features

1. Screws: You’ll find screws to open and close the Aranet PRO Plus case.
2. SIM card holder: This is where you put your SIM card.
3. Sensor Data Light: Flashes amber whenever it gets information from a sensor.
4. Cellular Connection Light: Flashes orange slowly if there’s no SIM card or no connection. Flashes quickly with pauses when connected to the cellular network.
5. Wi-Fi Light: Yellow light means the Wi-Fi is on and the device is connected, or it’s in Access Point mode.
6. Ethernet Light: A yellow light indicates the Aranet PRO Plus is hooked up to your network with a cable.
7. System Light: Green means the system is up and running.
8. Power Light: Green means the device has power.
9. Mounting: The case has four holes for screws (4 to 4.5mm) so you can mount it on a smooth surface.
10. Warranty Seals: These are nylon screws.
11. Humidity Membrane: This part helps the device work properly in different environments.
12. Network Reset Button: Press and hold for at least 5 seconds to reset the network settings and the “root” user password.
13. Ethernet port: Network and Power connection.

Base station setup

• Step 1
  • Unscrew the plastic cover for the ethernet port.
• Step 2
  • Disassemble all the plastic parts.
• Step 3
  • Push out the water seal from the plastic cover.
• Step 4
  • Apply plastic nut, water seal, and plastic cover to the ethernet cable as shown in the picture.
• Step 5
  • Connect an ethernet cable to the base station.
• Step 6
  • Push all parts together and screw them securely.
• Step 7
  • Use your Power over Ethernet (PoE) to power the base station. For the PoE injector provided by Aranet, use the “out” port.
• Step 8
  • Wait for the Wi-Fi light to turn on.
• Step 9
  • Please find the base station name and login credentials on the sticker located at the base station.
• Step 10
  • Find and connect to the Aranet local Wi-Fi access point from your phone, tablet, or computer.
• Step 11
  • After connecting, access the Aranet user interface at http://192.168.206.100.
• Step 12
  • Login to the base station using credentials.

Start using the base

• SCAN THE QR CODE TO SEE ARANET PRO PLUS/PRO PLUS LTE BASE STATION USER GUIDE
• SCAN THE QR CODE TO SEE HOW TO PAIR SENSORS TO THE ARANET PRO / PRO PLUS BASE STATION

FOR MORE DETAILED INFORMATION ABOUT ARANET PRODUCTS, PLEASE VISIT ARANET.COM, CONTACT YOUR ARANET REPRESENTATIVE, OR WRITE TO INFO@ARANET.COM. PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. © SAF TEHNIKA, JSC. ALL RIGHTS RESERVED. V3.0

References

• Aranet
• Aranet

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>