qi2 Qi 2.0 Magnetic Wireless Car Charger User Guide
- July 22, 2024
- Qi2
Table of Contents
Qi 2.0 MAGNETIC WIRELESS CAR CHARGER
Specs
Magnetic Wireless Car Charger
- USB-C™ Input: 5V/3A; 9V/2.22A; 12V/1.67A
- Output: Up to 15W
20W Car Charger
- Input: DC 12V-24V
- Output: 5V/3A, 9V/2.22A, 12V/1.67A
Caution
DO NOT place any credit cards or other types of magnetic material near the
charging pad. Do not attempt to disassemble the wireless charging pad as it
may short circuit or damage the product. Keep at least 8″ (20cm) distance
between implantable medical devices such as pacemakers, cochlear implants,
etc. Keep this product in a dry and ventilated space. Do not place in direct
heat or use in high humidity environments. Do not use organic solvents to
clean surface.
Instructions
Attaching the VENT MOUNT:
WARNING: Please do not text and drive. Do not place near an airbag.
1. Make sure the air vent is clean and free of dust.
2. Loosen the large socket nut on the back of the magnet mount and push the vent ball joint into the hole until it snaps into place.
3. Screw the socket nut tight this secures the mount to the base.
4.Turn the smaller socket nut until the vent hook mechanism is at proper
length.
NOTE: Vent hook latch rotates for compatibility with vertical or horizontal
vent mounts.
5. Attach by pushing and placing the vent hook mechanism onto a vent blade and then screwing the socket nut until tight. The vent pads should be against your dash and it should be stable and secure.
Attaching the SUCTION MOUNT:
1. Unscrew the large socket nut and push vent clip ball joint into the hole until it snaps into place.
2. Screw the socket nut back on until tight this locks the vent clip onto the wireless charging pad and holds the adjustable support base in place.
Using your Magnetic Wireless Car Charger :
- Connect the USB-C to USB-C cable to the USB-C port of the Magnetic Wireless Car Charger.
- Connect the USB-C connector into the included car charger and plug it in.
- Place the back of your Apple iPhone® MagSafe® device against the Magnetic Wireless Car Charger until it automatically aligns and snaps into place.* Charging will begin automatically.
*Works with MagSafe cases. Non-MagSafe cases must be removed before charging.
Limited Lifetime Warranty
This product is fully warranted against defects in materials and workmanship for the lifetime of the product, so long as the manufacturer continues to make this product. If a product fails due to a manufacturing defect, we will replace it upon proper proof of purchase by the original purchaser. Replacement product will be subject to shipping and handling charges. Damages through normal wear and tear, alteration, misuse, neglect, accident, service by anyone other than the authorized service center, or act of God, are not covered by this warranty. For all warranty claims, the product must be returned in accordance with PureGear’s return policy.
The “Qi2” symbol is a trademark of the Wireless Power Consortium.
USB-C is a trademark of USB Implementers Forum.
All trademarks and trade names are used for reference purposes only and are the property of their respective owners.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator & your body.
FCC Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy; if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different form that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
www.pure-gear.com
© 2024 F00227PG
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>