Godox SL200II Bi Color LED Video Light Instruction Manual

Bi-color LED Video Light
SL200II Bi
Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

When using your photographic equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Close supervision is necessary when any appliance is used by or near children.
   Do not leave appliances unattended while in use.

3. Care must be taken as burns can occur from touching hot parts.

4. The appliance switch is provided with the symbols 0 indicating off and 1 indicating on. The symbols and may be used for this purpose.

5. Do not operate the appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified serviceman.

6. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

7. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.

8. Always unplug the appliance from the electrical outlet before cleaning and servicing and when not in use. Never yank the cord to pull the plug from the outlet. Grasp plug and pull to disconnect.

9. Let the appliance cool completely before putting it away. Loop cord loosely around the appliance when storing.

10. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.

11. To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified serviceman when service or repair work is required. Incorrect reassembly can cause electric shock when the appliance is used subsequently.

12. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons.

13. Connect this appliance to a grounded outlet.

14. Disconnect this unit from its source of supply before replacing the projection lamp.

15. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
    does not fit, contact a qualified electrician. Do not modify the plugin anyway.

SAVE THESE INSTRUCTIONS

Foreword

Thank you for purchasing!
Bi-Color LED Video Light SL200IIBi, an upgrade version of SL200II, gets all the excellent quality and performance of SL200II, and adds the flexibility of expansive color temperature range, bringing photographers a more creative shooting experience. Light body 360°rotated offers excellent flexibility for more shooting angles. Power output up to 200W, strong power and stable output. Built-in 9 FX special provides more creative possibilities. This LED light can benefit interviews, broadcasting, cinematography,  online streaming, studios, location shooting and other shooting occasions, with a wide range of applications.
Features:

• With color temperature adjustment from 2800K to 6500K.
• With 9 FX lighting effects mode to simulate various of the shooting scene.
• Silent mode: without noises and interference.
• Built-in Godox 2.4G wireless & wirelessly adjust parameters.
• With stable light source and 0% to 100% precise light adjustment.
• With 16 groups and 32 channels of wireless control.
• With a U-type bracket to adjust different angles easily.
• Bowens-mount enables to installation various of accessories.
• Clear LCD Screen.
• Excellent heat dissipation.

**** Warning

• Always keep this product dry. Do not use in rain or in damp conditions.
• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
• Keep out of reach of children.
• As this product do not have a waterproof function, please take measures of waterproof in rainy or damp environment.
• Do not use the product in the presence of flammable gases, chemicals and other similar materials.
• CAUTION: Hot parts!When the product is always on and flickering, please do not touch the high-temperature part of the LED head.
• When replacing product accessories, please turn off the LED light and perform a cold cut.
• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person.
• The lamp shall be changed if it has become damaged or thermally deformed.
• The luminaire is intended for professional use only.

Name of Body

LCD Panel

Included Items

Separately Sold Accessories

The product can be used in combination with the following accessories sold separately, so as to achieve best photography effects: RC-A6 Remote Control, Power Inverter, Softbox, Photographic Umbrella, Light Stand, Grid, Beauty Dish, Snoot, etc.

Power Connection

Use the power cord to connect the LED light to an AC power source and turn on the power switch.

Operation

Mode Selection

1. LED silent mode: Short press< > fan button, make < > fan button not lighting up, and the Silent Mode is turned on. When the silent mode is turned on, the adjustable range of brightness is 0%~50%.
2. LED lighting effects modes: Short-press the FX button to enter or exit the special effects. When entering the FX modes, the FX icon will be displayed on the LCD panel. Then, turn the CCT/FX select dial to choose one mode from the 9 special effects modes to achieve creative shooting.
   Display| FX1| FX2| FX3| FX4| FX5| FX6| FX7| FX8| FX9
   ---|---|---|---|---|---|---|---|---|---
   Scene| Flash1| Flash2| Storm1| Storm2| TV| Broken bulb| Candle| Fire| Firework
3. LED strong power mode: Short press < >fan button, make < > fan button lighting up, the LED enter into strong power mode, then the power output up to maximum value.

Settings

Light Brightness Adjustment
In LED mode, the light brightness of LED light can be adjusted by turning the DMX select dial from 0% to 100%. And the light brightness will be clearly displayed on the LCD Panel. Color Temperature Adjustment
In continuous LED mode, turn the CCT/FX select dial to adjust the color temperature from 2800K to 6500K. And the color temperature value will be precisely displayed.

Wireless Control

Bi-color LED Video Light SL200IIBi equips with wireless receiving function. The remote control RC-A6 can be purchased separately, which can control 16 groups of lights, 32 channels, and 99 wireless IDs at the same time, with strong anti-interference.
Note: Please adjust the channel (CH), group (GR) and ID of the LED light and RC-A6 remote control to the same value before using.

Group GR, Channel CH and ID Setting
GR Setting : Short press GR button, then turn CCT/FX select dial to choose a group from A, B, C, D, E, F, and 0 to 9.
CH Setting: Short press CH button, then turn CCT/FX select dial to choose a channel from 1 to 32.
ID Setting: Long press GR and CH buttons to enter ID setting interface. Then, turn the DIM select dial to choose ID from OFF and 01 to 99.

Technical Data

• Product design and specifications are subject to change without notice.

Maintenance

This product, except consumables e.g. cable, is supported with a one-year warranty.
Avoid sudden impacts and the product should be dedusted regularly.
Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professionals.
Changes made to the specifications or designs may not be reflected in this manual.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note:

Note: This form shall be sealed by the seller.
Applicable Products
The document applies to the products listed on the Product Maintenance information (see below for further information). Other products or accessories (e.g. promotional items, giveaways, and additional accessories attached, etc.) are not included in this warranty scope.
Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.
How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you a maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.
Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases:

1. The product or accessory has expired its warranty period;
2. Breakage or damage caused by inappropriate usage, maintenance, or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by an external force, contacting or exposure to the improper temperature, solvent, acid, base, flooding, and damp environments, etc;
3. Breakage or damage caused by the non-authorized institution or staff in the process of installation, maintenance, alteration, addition, and detachment;
4. The original identifying information of product or accessory is modified, alternated, or removed;
5. No valid warranty card;
6. Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
7. Breakage or damage caused by force majeure or accident; . Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakages within the maintenance scope.

Maintenance and Service Support Information
The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance Period(month)| Warranty Service Type
---|---|---|---
Parts| Circuit Board| 12| The customer sends the product to the designated site
Battery| 3| The customer sends the product to the designated site
Electrical parts e.g.battery charger, power cord, sync cable, etc.| 12| The customer sends the product to the designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover, locking device, package, etc.| No| Without warranty

Godox After-sale Service Call 0755-29609320-8062
GODOX Photo Equipment Co., Ltd.
Add Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District,
Shenzhen 518103, China Tel: +86-755-29609320(8062) Fax: +86-755-25723423
E-mail: godox@godox.com
godox.com
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>