Interiors 1900 ABY133W Fitzroy Solid Brass Wall Light Instruction Manual
- June 3, 2024
- Interiors 1900
Table of Contents
1900 ABY133W Fitzroy Solid Brass Wall Light
Instruction Manual
ABY133W Fitzroy Solid Brass Wall Light
Installation and Safety Instructions
Wall Light Fitting
Safety Warnings
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference. If you are in any doubt about
installing this product, consult a qualified electrician. This product is only
suitable for connection to a 220-240V~ 50Hz supply in accordance with current
IEE wiring regulations, and should be installed in accordance with local
building regulations. It is for indoor use only, and is not suitable for a
bathroom location.
This is a Class l product and must be Earthed. The terminal blocks are
supplied according to requirements of the fitting. IMPORTANT: Always switch
off the mains supply during installation or maintenance. We recommend that the
fuse is withdrawn or the circuit breaker switched off at the distribution
board whilst work is in progress (turning off the light switch is not
sufficient). Connection should be via a wall switch to enable safe isolation.
The product must be securely fixed to the mounting surface using the screws
and wall plugs supplied. The screws and wall plugs supplied are suitable for
“masonry” only. Other fixings are not supplied and must be purchased. Decide
on the position of the light fitting or remove existing light fitting. Note
the position of the electrical connections, and ensure there is a solid
mounting surface, Preferably a wooden joist or joist bridge, to support the
weight of the light fitting. Take care not to drill into any pipes or mains
cables beneath the surface during mounting holes preparation.
Never put anything on the product or hang anything on any part of this
product.
IMPORTANT: Ensure that all electrical connections are tight and that no
loose strands are left out of the terminal. Never fit bulbs of a higher
wattage than those specified on the label (as these may cause over heating and
damage the fitting). Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with your Local
Authority or local store for recycling advice.
Care and maintenance
For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use). Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
Troubleshooting
When the bulb does not light after installation:
Ensure there is no electricity failure.
Ensure all the connections are secure.
If you have any doubt about installation/use of this product, consult a qualified electrician.
Assembly Instructions
***** Product images may vary.
- Position the mounting bracket centrally onto the wall and mark the fixing holes onto the wall. Check that there are no hidden cables at these positions and drill pilot holes into the wall. (Please use correct type of screws or wall anchor for wall). Insert two suitable wall anchors into the pilot holes in the wall .
- Make electrical connections in the terminal block as shown in Fig. 2. Close the terminal box and check that all the insulation is inside the terminal box and there are no trapped wires. Ensure the terminal box is firmly closed. Place the terminal box and wiring inside the wall making sure not to damage any cables.
- Raise the fitting to the mounting bracket , and then secure with the fitting screws.
- Your wall lamp is supplied with two sets of sleeves, the short sleeve enables the use of the shade ring to accommodate soft shades (sold separately) and the long sleeve is to be used with `bare bulbs’. These can easily be swapped by removing the shade ring, unscrewing the candle drip from the fitting and replacing with the alternative candle drip.
- If using a soft shade fit the shorter candle drips. Position the shade on the bulb holder and secure with the plastic shade ring.
- Insert the correct bulbs (sold separately) as marked on the bulb holders.
- Turn on the power and test.
Scan QR code for multi-language https://qrco.de/bbiq6g
UK Manufacturer: BH17 7BY EU
Manufacturer: Brilliant AG
Brilliantstrasse 1, D-27442
Gnarrenburg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>