SYNCWIRE SW-WL770 Magnetic Wireless Charging Stand User Manual
- July 11, 2024
- SYNCWIRE
Table of Contents
User Manual
Magnetic Wireless
Charging Stand
SW-WL770 Magnetic Wireless Charging Stand
The Magnetic Wireless Charging Stand to snap and secure your iPhone for easy
viewing angles while getting a more efficient wireless charge at the same
time. The magnetic charging stand automatically connects your phone to the
sweet spot and begins to charge, avoiding charging slowdown or other
interference.
Note:
- Please connect USB-C cable to the power adapter with PD 18W or higher output.
- Provides 7.5W Max charging for the iPhone.
Product Diagram
- Charging Stand
- Charging Zone
- 1m USB-C Cable
Packing List:
- Magnetic Wireless Charging Stand
- User manual
Operation Steps:
- Connect to the power adapter (18W or 18W+) and switch on the power, then place the phone near the magnetic charging zone to start charging automatically.
- Adjust the phone viewing angles vertically or horizontally for convenient using.
Attention:
- If MagSafe function is not supported on the phone, it cannot adhere magnetically to the Wirelss Charger. Before using, please make sure that the phones support MagSafe, eg, iPhone 13, iPhone 12.
- Please use MagSafe phone cases. Since non-MagSafe or common phone cases will drastically weaken the magnetic adsorption between the phones and wireless charger, the phones cannot be fixed on the wireless charger.
- Do not place coins, cards, keys, or other magnetic goods.
- Do not disassemble, repair or reassemble the product.
- Do not knock or drop this product to avoid internal damage.
- Dispose of this product as per local law and regulations.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could avoid the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different fram that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance between 20cm the radiator your body.
FCC ID: 2ASUP- SW-WL770
Manufacturer’s Name: Shenzhen Leaderment Technology Co., Ltd.
Sample Description: Magnetic Wireless Charging Stand
Model number: SW-WL770
Operating Temperature: -10° C to 40° C
Manufacturer’s Name: Shenzhen Leaderment Technology Co., Ltd.
Sample Description: Magnetic Wireless Charging Stand
Model number: SW-WL770
Operating Temperature: -10° C to 40°C
This device was tested for operations. To comply with RF exposure
requirements, a minimum separation distance of 20cm must be maintained between
the user’s body and the charger, including the antenna. Third-party belt-
clips, holsters, and similar accessories used by this device should not
contain any metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and should be
avoided. Use only the supplied or an approved antenna.
The device is in compliance with the essential requirements and other relevant
provisions of the UK Radio Equipment Regulations SI 2017:1206 (as amended).
- The device complies with RF specifications when the device used at 20cm form your body.
Declaration of Conformity:
Hereby, Shenzhen Leaderment Technology Co., Ltd. Declares that the product
SW-WL770 is in compliance with the following Directives: Radio Equiprnent
Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The
Restriction of the Use of Certain Hazardous Substances in Electrical and
Electrical Equipment 2012. The Full test of the UK declaration of conformity
is available at the following internet address:
https://vww.leaderment.com/
Radiated H-Field | -10.2dBuA/m(@10m) (only for EU and UK) |
---|---|
TX/RX frequency range | 110-205 kHz (only for EU and UK) |
TX/RX frequency range | 115-205 kHz (only for FCC ) |
Manufacturer’s Name: Shenzhen Leaderment Technology Co., Ltd.
Sample Description: Magnetic Wireless Charging Stand
Model number: SW-WL770
Operating Temperature: -10°C to 40°C
This device was tested for operations. To comply with RF exposure
requirements, a minimum separation distance of 20cm must be maintained between
the user’s body and the charger, including the antenna. Third-party belt-
clips, holsters, and similar accessories used by this device should not
contain any metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and should be
avoided. Use only the supplied or an approved antenna.
This device in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU. All essential radio test suites have been
carried out. This restriction will be applied to all Member States of European
Union.
- The device complies with RF specifications when the device used at 20cm form your body.
Declaration of Conformity:
Hereby, Shenzhen Leaderment Technology Co., Ltd. Declares that the product
type SW-WL770 is in compliance with Directives 2014/53/EU & 2011/65/EU. The
full test of the EU declaration of conformity is available at the following
internet
address: https://www.leaderment.com/
Prolinx GmbH
Brehmstr.56, 40239 Duesseldorf Germany
Syncwire UK Ltd
C/O Lai and Co.109 Portland Street,
Manchester, M1 6N
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>