HONDA TAL-001 Upper Door Kit Instruction Manual
- June 15, 2024
- Honda
Table of Contents
HONDA TAL-001 Upper Door Kit
IMPORTANT INFORMATION
Notes
- Windows must be completely open when closing or opening Doors.
- If installing Side View Mirrors, use a soldering iron to create holes in Soft Cab.
- Hook and Loop Fasteners should be applied at a temperature of 70°F or above.
- Use Denatured Alcohol and thoroughly clean any area where Hook and Loop Fasteners will be installed.
- Installing and adjusting Soft Cab is easier with two people.
- When cleaning Soft Cab, use soap and water only. Do not use detergent, window cleaner, solvents.
- Do not use a dry cloth or rag on windows.
- Do not fold Soft Cab before storing. Zip windows closed and roll Soft Cab to store.
- Do not discard packaging until product has been successfully installed.
- Doors may be secured with Snaps only, Hook and Loop Fastener only, or a combination of Snaps and Hook and Loop Fastener.
- Any whiteness, clouding, wrinkles, or waves that develop will gradually disappear when Soft Cab is exposed to sunlight and/or heat. Use a heat gun or hair dryer to speed up this process. Do not overheat or heat in one area for an extended period of time.
- Windows must be rolled up when trailering machine.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATV® to verify that
they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Read instructions and view illustrations before beginning
- Raise Roof.
- Cut and install Hook and Loop to Cage in locations shown.
INSTALLATION INSTRUCTIONS
Use multiple smaller pieces to fit around any Clamps
- Cut and install Hook and Loop to Cage in locations shown.
Use multiple smaller pieces to fit around any Clamps
-
Place Soft Cab onto machine and loosely secure Straps.
-
Align Soft Cab to machine.
-
Cinch Straps tight.
-
Secure all Flaps to Hook and Loop fastener.
repeat all steps for passenger side installation
HOOK AND LOOP TO BODY ONLY INSTALLATION
(if Soft Cab is to be secured with Snaps, go to following page)
- Cut and secure Hook and Loop to flaps on lower inside portions of Door.
- Tightly pull Doors down and press Hook and Loop onto plastic.
THESE STEPS MUST BE DONE FOR EACH INSTANCE
-
Peel backing from Hook and Loop.
-
Fold flap down and firmly press along areas where Hook and Loop is installed.
wait 15 – 30 minutes for adhesive to setup -
Carefully open flap; use one hand to gently separate Hook and Loop Fastener from flap and plastic while opening.
-
Apply more heat to Hook and Loop.
Snaps installation
- Outline Snap with a paint marker, lipstick, or marker.
- To mark location, press Snap onto Body or Velcro.
- Install provided Snap.
- Secure Door to Snap.
- Repeat steps for remaining Snaps.
repeat steps for passenger side installation.
CUSTOMERS SUPPOER
Need help with your installation?
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>