LEMEGA CR4 DAB/DAB+ and FM Digital Radio Owner’s Manual

Owners manual

Introduction Safety Instructions

Please store this instruction manual for future reference.

• Do not use this product near water or moisture.
• Clean only with a dry cloth.
• Unplug this product from the wall outlet before cleaning.
• Place the unit on a solid surface.
• Do not put it in a closed bookcase or a cabinet that may keep air from flowing through its ventilation openings.
• Do not install near any heat sources, such as radiators, heat registers, stoves, or other appliances that produce heat.
• Protect the power cord from being walked on or pinched particularly at plugs and the point where they exit from the product.
• Servicing is required when the product has been damaged. Do not attempt to service this product yourself. Opening or removing covers may expose you to dangerous voltages or other hazards.
• Please contact the manufacturer to be referred to an authorized service center near you.
• To prevent the risk of fire or electric shock, avoid overloading wall outlets, extension cords, or integral convenience receptacles.
• Do not let objects or liquids enter the product.
• Use proper power sources. Plug the product into a proper power source, as described in the operating instructions or as marked on the product.

CONTROLS, CONNECTORS

GETTING STARTED

ACCESSORIES INCLUDED Carefully remove the unit and all accessories from the package.
Please verify that you have all the following accessories before recycling the gift box.
• 1 CR4 unit
• 1 Owner’s manual
• 1 Warranty card
• 1 Power adapter

UNDERSTANDING THE CONTROL FUNCTIONS

QUICK SETUP
Fully extend the Telescopic antenna to ensure good reception in both DAB and FM Radio modes. It may be necessary to alter the position of the DAB Digital Radio and/or the Telescopic antenna to achieve the best signal.

1. Connect the power cable to the input in the side of the CR4 and then plug the cable into an outlet or insert the four “AA” batteries into the battery compartment to power on.
2. Fully extend the rear telescoping antenna.
3. Press the Power knob on the front to turn on the CR4.
4. When powered on for the first time in DAB mode, the C4 will initiate an auto scan. When complete, The display will indicate how many stations were received. Be sure the rear antenna is fully extended during the auto scan.
5. Press the SOURCE button to select the desired source.
6. Adjust the volume to the desired level using the SELECT knob.
7. In DAB mode, the TUNE+/TUNE- button allows you to navigate between different stations.

GUIDE TO FEATURES

1. PRESET: Long press buttons 1, 2,3+ to preset and save your favorite stations save 20 favorite stations); Short Press buttons 1,2, 3+ to select the favorite station to play or Preset recall. You can save 20 stations by pressing button 3+ and by scrolling the preset list to achieve.

2. INFO: View more information about the station or track playing. Press again to cycle through further information screens then return to the normal playing screen.
   FULL SIDESHOW: Press and hold the INFO button to switch DAB normal playing screen image to full-screen slide show image.

3. SELECT/ VOLUME/MUTE/SNOOZE:
   a.Power: Turn on or back to standby mode (showing clock and date), cancel sleep, or cancel alarm function.
   b.VOLUME: Rotate the scroll button to adjust the volume up or down during playback.
   c.MUTE: Press the scroll button to mute the music when playing.
   d.SELECT: Rotate the scroll button scroll through a menu or station list. Press the scroll button to select the chosen option. Press and hold the Select scroll button to auto-scan DAB/FM stations.
   e.SNOOZE: Press the scroll button to snooze a set time when the alarm sounds.

4. / Tune+: Press to select the next track under FM/DAB/ Bluetooth Mode; Press and hold the Tune+ button for 2 seconds to auto-scan the stations under the FM mode.

5. MENU: press the MENU to show the MENU for the current model. Press again to show now playing screen.

6. BACK: press the BACK to return to the previous screen.

7. : Press to select Play/Pause under BT mode.

8. SOURCE : Press to Source to select different modes DAB, FM, Bluetooth.

9. / Tune-: Press to select the previous track under Bluetooth mode.

DAB mode

1. In DAB mode, press the MENU button to enter the menu list. Press the TUNE+/TUNE- button to select an option through the list of menus or rotate the SELECT knob to scroll the menu list. Then, stop at your preferred option and Push the SELECT knob to confirm. The menu options are: full scan/ manual tune/ DRC /prune/ system.

2. Full scan – under menu list, rotate the SELECT knob to select “Full scan” through the list of menus, Push the knob to confirm and full scan starts automatically to fig.4. Once a scan is completed, the radio returns to play the previously-selected station or first station on the station list.
   Note: if no radio station is found, it shows “No DAB station”. For better reception, extend the antenna or do the full scan again in another place.

3. Manual tune – as well as the normal method of scanning, you can also manually tune to a particular channel/frequency. This can be useful for adjusting your antenna to achieve the best possible reception and scanning a particular channel to update the station list. Under the menu list, press the TUNE+ button or rotate the SELECT knob to select “Manual tune” through the list of menus, Push the SELECT knob to confirm. Rotate the SELECT knob to select a particular channel/frequency and then Push the SELECT button to confirm the setting to fig.5. The display shows a live indication of the received signal strength on the selected frequency.
   Adjustments to your antenna will be manifested in the received signal strength displayed.

4. DRC (Dynamic range compression) – this function reduces the difference between the loudest and quietest audio being broadcast. Effectively, this makes quiet sounds comparatively louder and loud sounds comparatively quieter. Options: off (default)/high/low under menu list, press the TUNE+ /TUNE- button or Rotate the SELECT knob to select “DRC” through the Hist of the menu, Push SELECT button to confirm. Then press the TUNE+/TUNE- button or Rotate the SELECT knob to select a particular setting and Push the SELECT knob to confirm the setting.

5. Prune – this removes all invalid stations indicated in the station list with a’?’ in front of the station name. Under the menu list, Rotate SELECT knob to select “Prune” through the list of menu, Push the SELECT knob to confirm.

6. System – the System menu options are: Sleep /Alarm / Equaliser / Time / Backlight / Language!, Factory Reset / Software upgrade / SW version.

6.1 Sleep – when listening to the radio you can set a period of time before the radio enters ‘standby’ mode. Note: the radio must be active and not in ‘standby’ mode already.
Under the system menu, Rotate SELECT knob to select through the list of menus, push in SELECT knob to confirm Sleep to fig.9. Then press TUNE-/TUNE+ button or rotate SELECT knob to select < sleep off / 15mins / 30mins / 45mins / 60mins / 90mins > and Push SELECT knob to confirm.
6.2 Alarm – Press Menu>System setting> Alarm. There are 2 Alarms, you can press and hold the Play/Pause button to switch to Alarm 2. Alarm 1 set up: Press the SELECT knob to set on time/Source/ Frequency / Volume then push the SELECT knob to confirm the settings.
Parameters Alarm – Off I On Source – DAB/FM/Buzzer Frequency – Daily I Once I Weekends I Weekdays
6.3. Time – if there is any DAB+ radio signal, the machine will automatically update the time, there is no signal, which can also be set manually. “Set Time/Date: set hour / set minute / set month / set date> set year > saved Auto-update options: update from Any / update from DAB / update from FM / no update Set 12/24 hour: 12hour/24 hours *Set date format: DD-MM- YYYY.
6.4. Backlight – this radio display has a backlight that can be adjustable. You can select the time out of the display backlight of your radio. Under the system menu, press the TUNE+/TUNE-button or rotate the SELECT knob to select”Backlight” through the list of menus, Push the SELECT knob to confirm. You can now use the TUNE+/TUNE- button or rotate SELECT knob to select < 10sec / 20sec / 30sec / 45sec / 60sec / 90sec / 120sec / 180sec / On

, and Push SELECT knob to confirm.
6.5. Language – the language used for display messages can be selected from the below options: English I Espanol I Francais I Italiano I Nederlands I Norsk I Polski Suomi I Dansk I Deutsch. Under the system menu, press the TUNE+/TUNE- button or rotate the SELECT knob to select “Language” through the list of menus, Push the SELECT knob to confirm. Cycle through the Language menu by pressing the TUNE+/ TUNE- button or rotating the SELECT knob to select, select and stop at a particular language, Push the SELECT knob to confirm.
6.6. Factory Reset – this function clears all user-defined settings, replacing them with the original default values, so time/date, preferences/settings, DAB station list, and preset stations are all lost. Under the system menu, Rotate the SELECT knob to select “Factory Reset” through the list of menus, Push the SELECT knob to confirm. Then, rotate the SELECT knob to choose and Push the SELECT knob to start the factory reset.
6.7. Software Upgrade – From time to time, CR4 may make software upgrades available with bug fixes and/or additional features.
This feature is for the service center.
6.8. Software version – this is used to display the current software version. Under the system menu, rotate the SELECT knob to select “Software version” through the list of menus. Push the SELECT knob to confirm. Then, the existing SW version will be shown.
FM mode

1. In FM mode, press the MENU button to enter the menu list. Rotate the SELECT knob to select the option through the list of menus.
   Then, stop at your preferred option and Push the SELECT knob to confirm. The menu options are scan setting, audio setting, and system.

2. Scan setting – by default, FM scans stop at Strong stations only. Options: Strong stations only /All stations under menu list, rotate the SELECT knob to select a particular option in “Scan setting”, then Push the SELECT knob to confirm the change to the new setting.

3. Audio setting – by default, all stereo stations are reproduced in stereo. For weak stations, this may result in poor-quality audio. The audio quality can be improved using mono. Options: Stereo allowed Forced mono under menu list, rotate the SELECT knob to select a particular option in “Audio setting”, then Push the SELECT knob to confirm the change to the new setting. It will automatically change to a new setting after 3 seconds.

4. System – Please refer to above description point 6 “System”.

Bluetooth Mode
Bluetooth mode allows CR4 to act as a wireless speaker playing audio content from a connected Bluetooth-capable device. To enter Bluetooth mode: Press SOURCE to choose Bluetooth mode To connect a Bluetooth-capable device. Use your Bluetooth-capable smart device to pair and connect with the CR4.
System – Please refer to above description point 6 “System”.

TECHNICAL SPECIFICATION

Model:
Type:
Speaker:
Power:
Supply:
Dimension (mm):
Weight:| CR4
DAB & FM Radio
1 X 2.5″ full-range speaker
5W RMS Power
5V DC
174 X 109 X 100MM
0.86KG
---|---

Specifications are subject to change without notice.
www.lemegaaudio.com
info@lemegaaudio.com
DISPOSAL OF THE OLD DEVICE This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose of them in accordance with any applicable local laws of the requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in the treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).

CR4 DAB &FM Radio
If you have any questions or suggestions,
please share with us
info@lemegaaudio.com
www.lemegaaudio.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>