ATEC IOT TWZT-T009D-H Zigbee Module User Manual
- June 15, 2024
- ATEC IOT
Table of Contents
- Application
- Quality
- Appearance and Characteristics
- Overall Service Scenario
- General Features
- Absolute Maximum Rating
- Electrical Specification
- Electrical Specification
- Mechanical Information
- User Quick Manual
- Packaging
- Disclaimers
- Certification
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
**ATEC IOT TWZT-T009D-H Zigbee Module User Manual
**
Application
This Specification is applied to ATEC IoT Zigbee Module (TWZT-T009D-H).
TWZT-T009D-H is Common Zigbee Module solution for IEEE 802.15.4(6LoWPAN)
applications. The robust network with PA(Power Amplifier) and diverse
interface(SPI, UART, I2C) make it possible to be used as various kinds of
applications. Specially, it is suitable for Gen2 Gateway and RTLS Anchor.
TWZT-T009D-H is composed of RF IC and necessary external component include the
Dipole Ant.
Quality
Quality should meet each condition which mentioned on this specification. However, the items which arenot mentioned on this specification follow the inspection agreements and standards which are agree with both companies.
Appearance and Characteristics
Appearance
Appearance should not be contaminated by harmful materials and should not have cracks, etc. Mechanical dimensions should meet the contents of clause 8.
Characteristic
Electrical Characteristics should meet the contents of clause 7.
Overall Service Scenario
General Features
Description
| Item | Description |
|---|---|
| Size | 36.0 x 28.0 x 10.0(mm) |
| Weight | Typ. 5g |
| Memory | Internal Flash : 128KB External Flash : 1MBSRAM : 20KB |
| Power | Operating Voltage : Typ. 3.3V (2.3V~3.6V) |
RF
| Tx Power| Max.10dBm
Data Rate| 250kbps
Antenna| PCB Pattern Antenna
Network
| 20pin Interface| UART for FW Downloading SPI for Communication
Wireless| 2.4GHz IEEE802.15.4 compliant RF Transceiver Range Extender (PA/LNA)
Security| Robust wireless network (LGIT own protocol)
Protocol| Compatible with LGIT protocol communication devices
Comm. Range| Max. 30m (under LoS) (1)
LoS (Line of Sight) : Without any sort of an obstacle between a gateway and end devices
Absolute Maximum Rating
Environmental Conditions
The normal operating environmental conditions are those as below. In such conditions, ESL must be in conformity with the present specification. The conformity to such requirement must be certified by the manufacturer
| Parameter | Condition | Min. | Typ. | Max. | Unit |
|---|---|---|---|---|---|
| Operating Environment | Temperature | -20 | – | 85 | ℃ |
| Humidity | – | 35 | 80 | %RH | |
| Storage Environment | Temperature | -30 | – | 85 | ℃ |
| Humidity | – | 35 | 80 | %RH |
[Notice]
TWZT-T009D-H is design to be used indoor/Ceiling. It does not guarantee outdoor conditions
Electrical Conditions
The operating electrical conditions are those as below. In such conditions the
ESL must be in conformity with the present specification. All devices can be
damaged or non-operated over the specification as below.
The conformity to such requirement must be certified by the manufacturer.
| Parameter | Condition | Min | Typ. | Max | Unit |
|---|---|---|---|---|---|
| Supply Voltage | DC Power Supply | 2.3 | 3.3 | 3.6 | V |
| Power Consumption | @ 3.0~3.3V (Active Tx) | – | – | 200 | mA |
| @ 3.0~3.3V(Active Rx) | – | – | 15 | mA | |
| ESD Protection | HBM(150pF/330Ω) (1)Air Condition @Soft Fail | -2 | – | +2 | kV |
[Notice]
TWZT-T009D-H is ESD sensitive device. Precaution should be used when handling the device in order to prevent permanent damage.
Electrical Specification
IEEE802.15.4
The TWZT-T009D-H supports IEEE802.15.4.
General Specification
- Standard : Only IEEE802.15.4 PHY
- Frequency : 2405 ~ 2480MHz
- Channel : 16CH. (5MHz Spacing)
- Modulation : DSSS/O-QPSK
- Max. Data Rate : 250Kbps
Electrical Specification
- Channel power depend on each country regulations (EX. KC, etc)
- The electrical specification which is shown below is ATEC IoT internal specification.
-
All values depend on surrounding environment and current statement of access point
RF PerformanceParameter| Condition| Min| Typ| Max| Unit
Output Power| @ CH2440| –| –| 10| dBm
Receiver Sensitivity| PER=1%(Required -85)| –| -92| -85| dBm
Frequency Tolerance| Required Max. ±75kHz| -75| –| 75| kHz
Error Vector Magnitude| Required Max. 35%| –| –| 35| %
Antenna Performance
Antenna
The TWZT-T009D-1 uses PCB pattern antenna for 2.4GHz frequency band.
VSWR
TEST METHOD
Radiation Pattern and Gain
**TEST METHOD
**
- Network Analyzer
- Signal Interface : Coaxial Cable
- SMA Connector
- Test PCB Antenna
TEST DATA
Radiation Pattern and Gain
TEST METHOD
- Network Analyzer
- Signal Interface : Coaxial Cable
- Test PCB Antenna
- Dual Polarized Antenna
- Shield Room
Radiation Pattern
2405 MHz
2440 MHz
2480 MHz
Efficiency
| Frequency(MHz) | 2405 | 2440 | 2480 |
|---|---|---|---|
| Efficiency(dB) | -2.11 | -1.5 | -2.17 |
| Efficiency(%) | 61.50 | 70.72 | 60.68 |
| Peak Gain(dB) | 1.8 | 2.53 | 1.94 |
[Notice]
This data is measured when TWZT-T009D-H is connected to the 4thSlot of
Gen2Gateway Board. Gen2 Gateway has 7 slots for diverse modules. The 4thSlot
is the
middle slot of whole 7 slots of it.
Antenna Performance
Gen2 Gateway Slot Information
Interface Information
| # | Name | I/O | Description |
|---|---|---|---|
| 1 | GND | G | Common ground |
| 2 | SPI_CS | O | Enable input for SPI interface |
| 3 | SPI_MISO | I | SPI data input |
| 4 | WAKE UP | O | wake up signal |
| 5 | UART_TX | I | NC |
| 6 | UART_RX | O | NC |
| 7 | VDD | P | 3.3V external DC supply |
| 8 | VDD | P | 3.3V external DC supply |
| 9 | GND | G | Common ground |
| 10 | GND | G | Common ground |
| 11 | GND | G | Common ground |
| 12 | NC | – | NC |
| 13 | TEST_PIN | O | Firmware Download Enable Pin |
| 14 | GND | G | Common ground |
| 15 | RESET | I | Reset input/output(active low) |
| 16 | IRQ | I | Interrupt output to the host processor |
| 17 | GND | G | Common ground |
| 18 | SPI_CLK | I | SPI interface clock |
| 19 | SPI_MOSI | O | SPI data input |
| 20 | GND | G | Common ground |
| # | Name | I/O | Description |
| --- | --- | --- | --- |
| 1 | GND | G | Common ground |
| 2 | SPI_CS | O | Enable input for SPI interface |
| 3 | SPI_MISO | I | SPI data input |
| 4 | WAKE UP | O | wake up signal |
| 5 | UART_TX | I | NC |
| 6 | UART_RX | O | NC |
| 7 | VDD | P | 3.3V external DC supply |
| 8 | VDD | P | 3.3V external DC supply |
| 9 | GND | G | Common ground |
| 10 | GND | G | Common ground |
| 11 | GND | G | Common ground |
| 12 | NC | – | NC |
| 13 | TEST_PIN | O | Firmware Download Enable Pin |
| 14 | GND | G | Common ground |
| 15 | RESET | I | Reset input/output(active low) |
| 16 | IRQ | I | Interrupt output to the host processor |
| 17 | GND | G | Common ground |
| 18 | SPI_CLK | I | SPI interface clock |
| 19 | SPI_MOSI | O | SPI data input |
| 20 | GND | G | Common ground |
Mechanical Information
Mechanical Dimension
:Size 28.0 x 36.3 x 9.8 (mm)
:Weight Typ. 5.1 g
Assembly
Label Specification
Product Labeling Specification
User Quick Manual
Zigbee Module User Manual
Zigbee Module is suitable for Gen2 Gateway.5 Slots of Gen2 Gateway can be used
for Zigbee. To fulfill the ESL System, at least 2 Zigbee Modules should be
inserted to the Gateway.
Likewise this picture, when you inserting modules, be careful with the
directions. Modules will not be able to be putted in when the inserting
direction is opposite.
LED Alarming
When Modules are working abnormally, three LEDs(Power, Status, Ethernet) would
blink to alarm the unusual state.
The abnormal phenomenon could happen when you forced pull out the modules or
module malfunctions.
Packaging
Gift Box
| No. | Item | Q’ty (EA) | Spec. |
|---|---|---|---|
| 1 | PE bag | 1 | 1EA per 1 Gift Box, 100EA per 1 Carton |
| 2 | ZIGBEE Module | 1 | Size (WxDxH): 28.0 x 36.3 x 9.8 (mm) |
| 3 | Gift Box | 1 | 1. Material : SC4002. Size (WxDxHxt) : 52 x 15 x 142.5 |
x 0.5t mm
4| Gift Box Label| 1| 1. Material: PET(White)2. Size(WxDxt): 50 x 30 x
0.1t
Outer Box
| No. | Item | Q’ty (EA) | Spec. |
|---|---|---|---|
| 1 | Gift Box | 100 | 1. Material : SC4002. Size (WxDxHxt) : 52 x 15 x |
142.5 x 0.5t mm
2| Certification Paper| 1| 1. Material: Paper(White)2. Size: A4
(WxH): 210 X 297
3| Inner Pad| 3| 1. Material : KLB.K.K/A2. Size (WxDxt): 415 x 290 x
4t mm
4| Outer box| 1| 1. Material : KLB.K.K/A2. Size (WxDxHxt): 420x 295
x 138 x 8t mm
| No. | Item | Q’ty (EA) | Spec. |
|---|---|---|---|
| 1 | Outer box | 1 | 1. Material : KLB.K.K/A2. Size (WxDxHxt): 420x 295 |
x 138 x 8t mm
2| Label_Carton| 1| 1. Material: Art-paper(White)2. Size(WxDxt):
120x60x0.1t
3| Tape OPP| 1| “H” type / 50*50 CLEAR
Pallet Packing
| No. | Item | Q’ty (EA) | Spec. |
|---|---|---|---|
| 1 | PLASTIC- PALLET | 1 |
- Material : PPC(재생) / BLK
- Size (WxDxH): 1200 x 1100 x 120mm
2| Cap_Box| 1|
- Material : : KLB225.CK.CK.SK.KLB225/B 골
- Size (WxDxHxt): 1160 x 1010 x 100mm x 8t
3| P.P Band| –|
4| Plastic Wrapping| –|
5| Fragile Label| 1|
- Material : Art Paper
- Size (WxH) : 200 x 120mm
Disclaimers
- ATEC IoT is not responsible for any damages caused by any accidents or operational environments exceeding the absolute maximum ratings.
- Consultation with ATEC IoT is recommended for unassured environments or operations to avoid any possible malfunctions or damages of the products or risk of life or health.
- Any unauthorized, without prior written consents from ATEC IoT, disassembly is prohibited if purposed for reverse-engineering. All defected devices must be reported to ATEC IoT and not to be disassembled or analyzed.
- The product information can be modified and upgraded without prior notice.
Certification
a. Rule Part 15.19(a)(3): This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
b. Rule Part 15.21: The users manual or instruction manual for an
intentional or unintentional radiator shall caution the user that changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•
- Consult the dealer or an experienced radio/TV technician for help
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>