SYNCWIRE SW1012 Selfie Stick Tripod User Manual

SYNCWIRE SW1012 Selfie Stick Tripod

SW1012
User Manual
1.62m Selfie Stick Tripod with Magnetic Phone Holder & Remote Shutter

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Warning
This device complies with Industry Canada licence-exempt RSS standard (s).

Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Product Introduction

Product Parameters

• Weight: Approx 430g
• Material: ABS+ Aluminum Alloy
• Folded Size: Ф 3.1*12.4 inch
• Height in Selfie Stick Mode: 63.0 inch
• Height in Tripod Mode: 63.8 inch
• Phone Holder Size: from 2.2 inch to 3.5 inch
• Magnetic Attraction Force >1 kg
• Remote Shutter Cell Battery Model:
• CR1620 3V Lithium Battery 70mAh
• Wireless Remote Shutter Distance: <10 m (33ft)
• Compatible Devices: fit ISO 5.0 and above, Android 4.3 and above devices.

Package Included

• 1* Selfie Stick Tripod with Wireless Remote Shutter
• 2* Metal Ring Patch
• 2* Cleaning Wipe Packet

Wireless Remote Shutter Instructions

1. Use for the First Time
   Please pull out the insulation sheet of the remote shutter first, then start to use the remote shutter normally.

2. Turn On/Off:
   Press and hold the camera button on the remote shutter for 3 seconds to turn the remote on or off. The green indicator light flashes slowly when the remote is on and not connected. If there’s no connection for 3 minutes, the remote will sleep, to press remote button once to active it.

3. Connect via Bluetooth:
   Turn on the remote shutter and go to your phone’s Bluetooth settings. Search for and connect to “SYNCWIRE” Bluetooth name.
   Once fully connected, the remote indicator light will turn off. it will automatically connect to phone next time when turn it on.

4. Taking Pictures and Videos with the Remote Shutter
   After remote device connected, please open your phone camera manually and press the remote button once to take a picture. Or select the video option manually, then press the remote button once to start recording. And press the button again to stop recording video.

5. Low Battery & Replacing Cell Battery
   Remote could not open or will be red light flashing when it is low battery.
   Note: * The new tripod already comes with a new cell battery.

Replacing Cell Battery:
Take remote off first, then use a coin or other tools to rotate the back cover to “unlock” direction, then turn remote upside down and gently tap the back cover to remove cover and replace with a new battery.
Finally put back the cover and rotate it to lock the cell battery well.
Cell Battery Model: CR1620 3V Lithium Battery 70mAh

1. Take off the remote shutter
2. Unlock the back cover
3. Remove cover and replace with a new battery
4. Lock the battery cover

About Android System Phones Connection:

Some Android phones use phone volume button to control camera or zoom. Please reset on phone camera settings, find volume key function, set the volume key function to shutter. (Do not select zoom or focus.)

Solutions When Remote control Failed to Connect with Phone

1. Clear some paired device when your phone Bluetooth have connected with too many devices.
2. Remove battery then put battery back again, try to turn remote on again.
3. Turn on phone Bluetooth, and turn on remote control, when “SYNCWIRE” is found on the mobile phone, click “connect”; When “connecting/pairing” is displayed on the interface, press remote button continuously and quickly to connect.
4. Remote control only supports mobile camera, but could not control live APP or other APPs.

Step 1 Open and Adjust Selfie Stick Tripod.

Tripod Mode
First, slightly unlock the 3 legs on the bottom to active the tripod legs; Then pull out the whole extendable stick pole, the tripod will fully open automatically (similar to an umbrella structure). Finally, put the fully opened tripod on flat surface and adjust the extendable pole height to find best shooting position.
Note: *Please do not pull the 3 legs directly to open the tripod.

• Be careful not to pinch vour fingers.

Selfie Stick Mode
Just pull out the extendable pole to use as Selfie Stick.

Step 2 Open & Rotate Phone Holder
Loosen the knob to rotate phone holder to find suitable angle then fasten the knob; so that you can easily attach phone device on.
Note: Rotate the cell phone clip to the same side as the remote button for more convenient use.

Step 3 Attach Phone Device on Holder

Using Phone Holder Clip
Open the phone holder clip and attach phone device on; then rotate phone holder to suitable angle. 360 °Free Rotation

OR Using Magnetic Attraction Phone Holder

Make sure the cell phone clip is closed, then attach phone on magnetic attraction phone holder. You can rotate phone holder for 360 °Free Rotation.
*Please check your phone model first then use metal ring according to demands;

1. iPhone 12/13/14/15… series without case Attach device on magnetic phone holder directly

2. iPhone 12/13/14/15… series with Magsafe case Attach device on magnetic phone holder directly

3. a. iPhone 12/13/14/15… series with non-magnetic case

First clean phone or phone case with cleaning wipe, then paste the metal ring on the back of phone or non-magnetic case, finally to attach phone device on magnetic attraction phone holder.

Note:

1. To better protect your phone, please paste the metal ring on the back of phone case.
2. Please notice that frosted phone cases or phone case without flat surface will not be recommended to adhere metal ring on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>