SYNCWIRE SW-WL647 Magnetic Wireless Car Charger User Manual

June 6, 2024
SYNCWIRE

SYNCWIRE logo n1

SYNCWIRE SW-WL647

User Manual
Magnetic Wireless Car Charger
Product Diagram

SW-WL647 - Product Diagram 1

  1. Air Vent Mounting Grip
  2. Pivot Locking Nut
  3. Ball Joint
  4. Release Knob
  5. Supporting bracket
  6. Magnetic Sticker
  7. Positioner
  8. Round Sticker

SW-WL647 - Product Diagram 4

Made of PC material, this wireless charger is equipped with a type-C cable. It supports fast charge for your phone at 7.5W with a QC 2.0 or QC 3.0 adapter, 15W with a PD 20W adapter with a built-in N52 magnetic ring. Exclusive multifunctional intelligent protection technology offers temperature control, over-voltage, over-current protection, surge protection, short-circuit prevention, and foreign object detection, which ensures you a safer charging experience.

Specification:
Product Model: SW-WL647
Input: 5V/3A, 9V/2A, 12V/1.5A
Output: 5W/7.5W/10W/15W
Operating Temperature: Normal 0-40°C
Certification: ROHS,CE,FCC,UKCA,PSE
Packing List:

Type-C Cable / Wireless Charger / Magnetic Sticker/ Positioner / Round Sticker / Manual

Operating Steps

1. Unscrew the pivot locking nut counterclockwise until you can push the ball joint into the back of the mount and then tighten it clockwise.

SW-WL647 - Operating Steps 1

2. Clamp to fasten the vent mounting grip on your car’s air vent.

SW-WL647 - Operating Steps 2

3. Counterclockwise the release knob until it can grip your car’s air vent securely.

SW-WL647 - Operating Steps 3

4. Paste the magnetic sticker to the back center of your phone case by using the positioner included enhancing magnetic forces.

SW-WL647 - Operating Steps 4

5. Place your wireless charging supported phone on the charging pad.

SW-WL647 - Operating Steps 5A

Notes:

  1. Keep the wireless charger away from water, liquid, or wet areas.
  2. Do not try to disassemble, repair or remold the product.
  3. Do not allow children or animals to chew or suck the device.
  4. Cut off the power before cleaning the charger.
  5. Only use a dry cloth or brush to clean the device.
  6. Stop using it if visible defects are observed on the charger.
  7. Unplug the device when unused for long periods of time.
  8. Make sure it’s compatible with your device before using it.
  9. Ensure no metal objects or magnetic material interferes with the wireless charger.
  10. If your case or back cover accessory contains metal material, please remove it before charging. (Except official MagSafe phone case)
  11. To achieve fast charge, a QC2.0/3.0 or PD adapter is required (not included).
FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC ID: 2ASUP- SW-WL647

Manufacturer’s Name: Shenzhen Leaderment Technology Co., Ltd.
Sample Description: Magnetic Wireless Car Charger
Model number: SW-WL647
Operating Temperature: -10° C to 40° C

Manufacturer’s Name: Shenzhen Leaderment Technology Co., Ltd.
Sample Description: Magnetic Wireless Car Charger
Model number: SW-WL647
Operating Temperature: -10° C to 40° C

This device was tested for operations. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the charger, including the antenna. Third-party belt- clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
The device is in compliance with the essential requirements and other relevant provisions of the UK Radio Equipment Regulations SI 2017:1206 (as amended).
1.The device complies with RF specifications when the device used at 20cm form your body.

Declaration of Conformity:
Hereby, Shenzhen Leaderment Technology Co., Ltd. Declares that the product SW- WL647 is in compliance with the following Directives: Radio Equipment Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electrical Equipment 2012. The Full test of the UK declaration of conformity is available at the following internet address: https://www.leaderment.com/

Radiated H-Field -10.2 dBμA/m(@10m)(only for EU and UK)
TX/RX frequency range 110-205kHz(only for EU and UK)
TX/RX frequency range 115-205kHz(only for FCC)

Manufacturer’s Name: Shenzhen Leaderment Technology Co., Ltd.
Sample Description: Magnetic Wireless Car Charger
Model number: SW-WL647
Operating Temperature: -10° C to 40° C

This device was tested for operations. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the charger, including the antenna. Third-party belt- clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out. This restriction will be applied to all Member States of European Union.
1.The device complies with RF specifications when the device used at 20cm form your body.

Declaration of Conformity:
Hereby, Shenzhen Leaderment Technology Co., Ltd. Declares that the product type SW-WL647 is in compliance with Directives 2014/53/EU & 2011/65/EU. The full test of the EU declaration of conformity is available at the following internet address: https://www.leaderment.com/

Radiated H-Field -10.2 dBμA/m(@10m)(only for EU and UK)
TX/RX frequency range 110-205kHz(only for EU and UK)
TX/RX frequency range 115-205kHz(only for FCC)

Prolinx GmbH
Brehmstr.56, 40239 Duesseldorf Germany

Syncwire UK Ltd
C/O Lai and Co.109 Portland Street, Manchester, M1 6N

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals