BASS JAXX EP-0713-R Wireless Charger True Earbuds Instruction Manual
- July 11, 2024
- BASS JAXX
Table of Contents
BASS JAXX EP-0713-R Wireless Charger True Earbuds
INSTRUCTION MANUAL
Thank you for purchasing the Wireless Charge True Wireless Earbuds.
This manual provides more information about the wireless earbuds, please read
the instructions before using.
Product Overview
- Remove the protective stickers before using.
- Touch Control/ On/Off Button/ Play/ Pause Music/ Answer/End Call
- LED Indicator/Built-in Microphone
- Charging Case Battery Level Indicator
- USB Type-C Charging Port
- Wireless Charging
Package Contents
1(One) Pair Earbuds 1.2in. x0.9in.x0.6iri.(3.1cmx2.4cmx1 .5cm)each
1( One) USS Type-C Charging Cable_ 9.81n. ~Scm)
1 (One0 Portable Charging Case 2.8m. x 1.~m . x 1in. (7.2cm x 4.7cm x 2.6cm)
1 (One) Instruction Manual
Specifications
Driver Diameter: 10mm
lmpedance: 32Ohms
Frequency Response : 20Hz-20 kHz
Sensitivity : 96dB+/-3dB
Power Supply:
Li-ion Battery 3.7V 30 mAh (per Earbud)
Li-ion Battery 3.7V 500 mAh (Charging Case)
Play Time: Total 16 Hours
Charging Time : 2.5-3Hours
Bluetooth Range: 32.8 Feet
Bluetooth Version: 5.3
USB Type- C cable included
Charging Case with wireless charging function
USS Type-C Charging Cable rating5V/1AMax.
Power On/Off
Power On
Press and hold down the On/Off Button of earbuds for 3 second sand the LED will flash.
Power Of
Press and hold down the On/Off Button of earbuds for 4 second sand the LED will turn Off .
-
Keep the distance between the earbuds and mobile device within 32.8 feet.
-
De-activate the Bluetooth function on your mobile device.
-
Take both Earbuds out from the Charging case and wait for 3 to 5 seconds for auto pairing. The earbud has indicator blinking alternatively in Red and Blue.
One of the earbud will be blinking in Blue slowly when auto pairing is done successfully on UR earbuds. -
Activate the Bluetooth function on your mobile device and select ” EP-0713 TWS ” from the list shown.
-
After pairing is successful, both earbuds will start blinking slowly in blue.
Attention: If the auto pairing is not successful, manual pairing between earbuds is essential by following below procedures:
- Make sure the earbuds are charged.
- De-activate the Bluetooth function on your mobile device. (if you had been paired the earbuds to some other mobile device(s) nearby, please sure to de-activate those device(s) too).
- Power on both earbuds simultaneously by pressing the On/Off buttons for 3 seconds and wait for 3 to 5 seconds for auto pairing. (Keep the Bluetooth function off on your mobile device before this operation.)
- Activate the Bluetooth function on your mobile device and select “EP-0713 TWS” from the list shown.
- After pairing successfully, both earbuds will start blinking slowly in blue.
Reconnect the wireless earbuds to your mobile device
When powered on, the wireless earbuds will automatically connect with the last successfully paired device.
Disconnect the wireless earbuds from your mobile device
Power off the wireless earbuds; or Switch off the Bluetooth on your mobile phone; or Leave the earbuds 60ft away from your mobile phone or further.
Answer/ Reject a call
When receive a call., press the On/Off Button onoe1 ( on either earbud) to
accept the call, or answer the call normally via your 1mo·bHe pho1ne.
Press and hold 2 seconds to, reject it.
End a call
To end the can, just press On/Off button at any side of earbud with Beep sound to end it.
Functions
Pause I Play Mu1si,c: Short Press on On/OFF Button1 Go back to previous song:
!Double• press left On/Off Button.
Advance to n1ext son1g: Double press Right 0n,Off Button.
Charging your Earbuds
- Open1 the charging case cover.
- Insert the Dual E.arbu1ds 1int.o the charging1 case.
- The earbuds will start the ch1arg1e automatically.
- LED indi1cator light will be turned on whe1n charging your earbuds.
- On1ce fully charged, the LED1 will be off .
Recharge the Ch11rging Case
Method 1
For your safety. please a:lways use· appropriate 5V output charger/Adapter to
charge the product.
DO 1NOT USE Quick Charging U:SB Adapter to charge the product, as it might
damage the product.
- Use the 1USB Type … ·C charging cable provided with th1e packaging.
- Connect the USB Type,-C plug to USB Type-C charging port on the charging case, then connect the USB plug to USB port on a wall adapter to begin charging.
- The LED on the charging case will flash during charge.
- Once Tully Charged, the LED will Stop Flashing.
Recharge the Charging Case
Method 2
You can also charge your Charging Case by wireless charging pad as below way.
Put the BOTTOM of the charging case on the wireless charging pad as picture shown
- Wireless charging pad is not included.
NOTE:
- You must select a qualified charger from a regular manufacturer.
- You must charge the charging case and earbuds if it has been not used for more than 6 months.
CAUTION: The USB Type-C charging cable included with this item is intended for use with this product. Only use the included USB Type-C charging cable to charge this product.
FAQ
If the wireless earbuds cannot be paired with your device, please try the
following:
Ensure that your earbuds are in pairing mode or reconnection mode Ensure that
Bluetooth search function of your mobile device is activated.
If the wireless earbuds will not turn on:
Make sure the earbuds are fully charged.
Can I change the battery for the charging case and earbuds?
The charging case and earbuds use a built-in non-detachable battery which
cannot be removed.
If the charging case cannot be recharged:
If you use a power outlet, ensure that the power supply is connected securely
and the outlet works.
If you use a wireless charging pad, make sure the correct location of charging
case is putting on charging pad and charging pad is powered.
Safety instructions for the lithium battery and charging the product
- The input voltage to the product is 5V 1 A.
- n order to charge the product in safe manner and reliable conditions, please only adopt certified appropriate charger/ adapter for charging the product.
- Only charge the product at ambient temperatures between 10 °C/ 50 °F and 40 °C/104 °F.
- Do not heat above 70 °C/158 °F, eg. Do not expose to sunlight or throw into fire.
- Switch off the product after use.
- Please note that we won’t take any responsibility for any wrong operation (eg. Voltage higher than SV) as this may result in severe injury or loss of property, and we cannot control the operating process during the time the user using this product.
- In extreme cases, abuse or misuse of Lithium battery pack can lead to explosion, heat generation, fire development or smoke development.
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radionv technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
The Bluetooth9 word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by 1616 Holdings, Inc. is under license. Other trademarks and trade names are those of their respective owners.
FCC ID : 2ADM5-EP-0713-L
FCC ID : 2ADMS-EP-0713-R
ITEM# EP-0713
Keep all relevant information for future reference
Distributed by 1616 Holdings, Inc. 701 Market Street, Suite 200 Philadelphia, PA 19106 Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>