MORRIS HAD-1301 Hand Dryer User Manual

MORRIS HAD-1301 Hand Dryer

Product Information

Specifications

• Model: HAD-1301
• Operation: Non-touch hand drying
• Hygiene: Anti-bacterial environmental protection material
• Power: AC power, rated voltage within 10% tolerance
• Safety Features: Leakage circuit breaker, anti-prank timer

Product Usage Instructions

Cautions

• Do not use in bathrooms or showers.
• Avoid spraying water on the unit.
• Keep children away from hanging on the unit to prevent falling.
• Avoid disassembling the unit unless following specific instructions.
• Turn off power during maintenance to prevent electric shock.

Installation and Operation

1. Ensure the power is turned off before installation.
2. Connect the unit to a fixed AC power line.
3. Install the drain tank and air filter before using the unit.
4. If there are abnormal conditions, cut off power, and contact the supplier for maintenance.

Features
The hand dryer offers non-touch drying for hygiene. It dries hands quickly with high-speed airflow and is energy-efficient. It is made of anti-bacterial material and provides automatic heating in winter for comfort.

Anti-Prank Timer
The machine has an anti-prank timer that stops operation after 25 seconds to prevent misuse. To continue use, remove and reinsert your hand.

Frequently Asked Questions (FAQ)

• Q: Can the hand dryer be used with wet hands?
  A: Yes, the hand dryer is designed to dry wet hands quickly and efficiently with high-speed airflow.

• Q: What should I do if the hand dryer stops working?
  A: If the unit stops working or shows abnormal conditions, cut off the power immediately to prevent accidents. Contact the supplier for maintenance or repair.

• Q: Is it safe for children to use the hand dryer?
  A: Children should always be supervised when using the hand dryer. Avoid letting children hang on the unit to prevent accidents.

USER MANUAL JET HAND DRYER

User Manual
Please read this manual thoroughly before using the hand dryer to ensure safe and correct Installation or operation. Please keep this manual in a safe place for reference at a later date.

Instructions

Features

• Because it is a [non-touch hand drying], it is very hygienic.
• Dries wet hands quickly with high-speed airflow, and requires only a small amount of electricity, so it is very economical.
• Do not dispose of garbage, do not use towels or paper towels.
• Anti-bacterial environmental protection material without any pollution.
• Automatic heating in winter is more comfortable to dry hands, no heating in summer, dry hands are cooler.

Anti-prank timer
In order to prevent prank, the machine will automatically stop running after about 25 seconds of continuous use (with an anti-prank timer). To continue using, retract hand and put it back in again.

Method

Specifications

Parts Name

Dimensions

Precautions before Installation

1. Precautions before Installation
   • Do not install the product (power cord) with power on.
   • When installing the unit, it must be select a suitable place and install it by a professional.
   • Otherwise there is a risk of injury due to falling of the unit.
   • Wear gloves when installing
   • You may be injured if you do not wear gloves.
2.  Do not install in the following types of location. (Otherwise this may cause malfunction)
   • Locations where the temperature can exceed-10℃ or 40℃.
   • Locations where the unit may come into direct contact with water.
   • Locations where the unit is under direct or strong sunlight.
   • Locations where easy to condensation.
   • Locations where corrosive, neutral or reductive gases are present.
   • Locations where sea level lower than 0m or higher than 2000m.
3. Installation location
4. Please install the machine according to the position shown in the picture. If the unit is installed too low, water may get on it when the floor is being cleaned.
5. The left side if the unit must be at least 150mm away from any walls due to the power switch is located on the left.
6. Ensure there are no mirrors or walls near the right side, as drops of water may splatter to the right when drying hands.(Recommended distance is at least 100mm)
7. Avoid locations where people or doors might bump into the unit.
8.  Choose a completely flat surface on the wall to install the unit.

About how the machine takes electricity

• This machine is recommended to use the socket to get power, and it is necessary to install a two-hole standard socket at a distance of 20-30cm from the machine.
• If you need to connect the power cord directly, please insert the junction box without cover in the installation position.

Installation Procedures

1. Please use single – phase alternating rated voltage supply!(Do not used with a power supply exceeding rated voltage ±10%)

   •  Please use 1.5mm²~2mm² for the power cord. (Single-strand wires other than 1.5mm²~2mm² cannot be used)
     (If the length of the power cord exceeds 11m, please try to use a 2mm² power cord in consideration of the voltage drop problem)

   •  Connect construction
     Please insert a coverless junction

   • box at the installation location for connecting the power cord.

   • If you don’t use a junction box, the power cord will be pinched on the back of the case and won’t fit well.

2.  Fix the mounting plate on the wall with the supplied mounting plate  fixing screws.

3. If you want to install it on a concrete wall, please use the hollow wall anchors, screws, etc. in the accessory bag of the machine for installation.

4. For non-concrete walls, they should be reinforced before installation.

5. In case of wiring installation, pay attention to the hole position on the sticker and the position of the junction box.

6. Paste the accompanying drilling sticker on the wall as shown in the figure. The sticker should be pasted flat on the wall. Drill four mounting plate fixing holes and two anti-theft screw holes according to the holes on the sticker.

7. Insert the hollow wall anchors into the six drilled holes, and fix the mounting plate as shown in the figure.

8.  Remove the drain tank and HEPA assembly

   • If the socket is used for power supply, you can directly hang the machine, screw in the anti-theft screw, and then install the HEPA component and drain box.
   • If you need to concept the power directly, follow the procedure below.

9.  Wiring and then fastening the body

10. Cut off the plug of the power cord on the machine and leave the length of the power cord at about 30CM.

11. Hang the back of the body on the hook of the mounting plate (2 places).

12. Pull the power line on the machine and the junction box to the side. The live line is connected to the live line, the zero line is connected to the zero line, and the ground wire is connected to the ground wire.

13. Sort out the power cord, plug it into the junction box as far as possible, and then push the machine gently towards the wall. if the machine is not installed in place, the anti- theft screw is not easy to screw in.

14. Install the front panel

15. Install HEPA components
    Push the air filter into the body and make sure it is in place.

16. Install the drain box

Test Run and Maintenance

Test Run

External maintenance of the machine

Before there is obvious contamination
On the surface of the antibacterial filter part (air filter), it exerts its antibacterial effect when bacteria are attached.

• If the surface dirt is too thick, it will affect the antibacterial effect.

• Wipe with a well wrung cloth
  If it is very dirty, wipe it with a cloth dampened with neutral detergent, and then wipe it with a dry cloth.

• Remove dirt from the sensor section
  In order to prevent malfunction, the power should be turned off.

Warning

• When performing maintenance, be sure to cut off the power supply and do not splash water on the machine.
• Notice
  Wear gloves during maintenance

Attention Please

1. Please use neutral detergent

2. Please do not use organic solvents, acidic or alkaline toilet detergents, nylon brushes, etc. for cleaning.
   (Otherwise it will damage the surface finish of the machine).

3. Only the part where the hand reaches can be cleaned and disinfected with alcohol. (Please do not use it outside the part where your hand reaches)
   Alcohol refers to alcohol for disinfection (with a concentration of 83% or less).

4. If you use chemical wipes, please confirm the precautions for its use.

Maintenance

• Drainage and cleaning of the drain tank
  Before the water is full (more than once a week)

• The water blown off the hands is called “drain tank”. Empty the drain water at any moment, in order to prevent accumulated water from exceeding the full level.
  It will start smelliness if the accumulated water remains in the tank for too long time.

•  Pull the drain tank out in the horizontal direction to ensure the drain water does not splatter out.

1. Open the cover of the drain tank
   Pull the cover up with your fingers in the two corners of the cover, and then remove the cover completely.

2. Wash out the interior of the drain tank

3. Close the drain tank cover, and re-attach it to the unit as original

4. Add 200cc (around 1 cup) of water through the drain hole.
   (To prevent it from getting clogged) Use the unit after confirming that the drain tank is in place.

Cleaning the HEPA
When the wind speed drops significantly or not less than once every six months

1. Remove the air filter
   Pull out the drain box first, hook the hook on the HEPA component frame with your fingers, and pull the component out horizontally.

2. Cleaning the air filter
   Beat it lightly by hand or use a vacuum cleaner;
   It can also use hairbrush to wipe off dust; Air filter can directly be cleaned with water, reuse after dry.

3. Re-attach to the unit
   Insert it all the way in, until it stops. (If air filter is not in place, the dirt or dust will enter the unit to shorten its service life and decreased the anti-bacterial result.)

Trouble Shooting

Drainage and cleaning of the drain tank
If you discover the following circumstance, please inspection and handling as following:

the ground-fault circuit breaker on.
Is there a power outage?| Turn the power switch on.
Are you putting your hands all the way in?| Put hands all the way in.
Unit works a long time after hands drawn out| Any dirt or other objects on the sensor?| Switch off the power button, and then remove dirt or foreign body on sensor after the power light gone out. When finished, switch on power button.
No hot wind| Is the ambient temperature too high?| This product has a built-in temperature control probe. When the ambient temperature is ≥ 25 ℃, the heater will stop heating.

lf the above actions do not work, turn off the power and the ground-fault circuit breaker, and call service department to inspect and repair it if necessary.

NOTICE ABOUT RECYCLING

• Your product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life,should be disposed of separately from your household waste. Please dispose of this equipment at your local community waste collection/ recycling centre.
• In the European Union there are separate collection systems for used electrical and electronic products.
• Please help us to conserve the environment we live in!

DECLARATION OF CONFORMITY

• Herewith, we state that this product complies with the requirements of below directives: EMC-Directive: 14 / 30 / EU

• Low Voltage Directive: 14/ 35 / EU
  CE Marking: 93 / 68 / EEC

• RoHS Directive: 11 / 65 / EU & Delegating Directive (EU) 15 / 863

• The detailed declaration of conformity can be found at

• www.morris.gr

• Kalliopi Karyda & Co, LP 87 A, 17th November sir. 55535, Pylea, Thessaloniki Tel. 2316 006600

• Fax. 2316 006650

• www.morris.gr

References

• Home - Morris

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>