MACHENIKE L7Air Wireless Mouse User Manual

July 10, 2024
MACHENIKE

MACHENIKE L7Air Wireless Mouse

PRODUCT OVERVIEW

SPECIFICATION

Connection Methods

Wired Mode: Turn the toggle switch to wired mode and connect the cable to the computer. (Wired priority: when the switch is in 2.4G or BT mode, connecting the mouse to the computer via USB will enable the mouse to operate in USB wired mode)

2.4G Mode: Toggle the switch to the 2.4G mode. The mouse indicator light will stay green for 3 seconds. If the receiver is not detected within 3 seconds, the indicator light will turn off. Once the receiver is recognized, the indicator light will switch to the corresponding DPI indicator color.

Bluetooth Mode: Toggle the switch to the Bluetooth mode. The mouse indicator light will flash blue 5 times then turn off. Once a Bluetooth device is recognized, the indicator light will stay blue for 3 seconds before switching to the corresponding DPI indicator color.

Pairing instructions

2.4G Mode: Turn the toggle switch to 2.4G mode. Press and hold the scroll wheel + left button + right button for 3 seconds to enter pairing mode. The mouse indicator light will slowly flash yellow for 20 seconds, and then insert the receiver into the computer USB. Once paired successfully, the yellow light will switch to the corresponding DPI indicator color.

Bluetooth Mode: Turn the toggle switch to Bluetooth mode. Press and hold the scroll wheel + left button + right button for 3 seconds to enter pairing mode. The indicator light will flash blue for 3 minutes. Once a Bluetooth device is successfully connected, the indicator light will stay blue for 3 seconds before switching to the current DPI indicator color.

Re-connection

2.4G Wireless Mode: The mouse indicator light will stay green for 3 seconds. If the receiver is not recognized within 3 seconds, the indicator light will turn off. Once the receiver is recognized, the indicator light will switch to the current DPI indicator color.

Bluetooth Mode: The mouse indicator light will flash blue 5 times then turn off. Once a Bluetooth device is recognized, the indicator light will stay blue for 3 seconds before switching to the current DPI indicator color.

Polling Rate

  • 2.4G Mode: Default polling rate is 1000Hz; adjustable in driver settings from 125Hz to 4000Hz.
  • 2.4G Mode(1k): Default polling rate is 1000Hz; adjustable in driver settings from 125Hz to 1000Hz.
  • Wired Mode: Default polling rate is 1000Hz.
  • Bluetooth Mode: Default polling rate is 250Hz(1k:125Hz) and cannot be adjusted.

DPI

The DPI indicator light reuses the left indicator light. After switching DPI, the left indicator light will display the corresponding DPI color. DPI values change with each press of the DPI button: 800 (red) – 1600 (green) – 2400 (blue – default) – 3200 (yellow) – 6400 (pink) – 26000 (orange).

Sleep Mode

The mouse enters sleep mode after 3 minutes of inactivity in wireless mode, with movement automatically waking it up. After 10 minutes, it enters deep sleep mode. Clicking any button wakes it up. There is no sleep function in wired mode.

Low Battery/Shutdown Level

When the voltage is below 3.5V, the low battery indicator light (LED) will flash red (flashing occurs when a button is pressed or the mouse is moved). When the voltage drops below 3.2V, the mouse will automatically shut down.

Charging

While charging, the left indicator light stays solid red until fully charged, then switches to the current DPI indicator light color.

Package List

  • Mouse*1
  • Receiver*1
  • Cable*1
  • User Manual*1

FCC NOTE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference
  2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF waking for Portable device:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals