MACHENIKE K500-B61W Mechanical Keyboard User Guide

K500-B61W
MECHANICAL
KEYBOARD
QUICK START GUIDE

K500-B61W Mechanical Keyboard

• Please read the manual before use and keep

OVERVIEW

TECH SPECS

MODEL|
---|---
CONNECTIVITY| USB Wired / Bluetooth / 2.4G
KEYS AMOUNT| ANSI Layout 61 Keys
Layout: 62 Keys
MULTI-MEDIA KEYS| 12
ANTI-GHOSTING KEYS| N-KEY ROLLOVER(NKRO)
BATTERY| 1600mAh
DIMENSION| 293.8’103.3’34.5mm
WEIGHT| 441g-± 31g
CABLE| About 1.5m
IMPLEMENTATION STANDARDS| GBJT 14081-2010

GETTING STARTED

Ι.WIRED CONNECTION

Turn the switch to the OFF position, after connecting to the computer via US6 you will be in wired mode, the “M” LEO tight will remain steady red. After fully charging, R wil turn into @ steady wivite light.

ΙΙ. WIRELESS CONNECTION

1. 2.4G Mode:
   Turn the keydoard switch to the 2.46 position, the “M” LED light will siowty flash green. After inserting the recerver and successfully connecting, the “M LEO light will remasn green. if you need to re-pair, press and hold “FN+Q/W/E keys” for 3 seconds, the “M” LED light will quickly flash green. After reinserting or replacing the USB port of the receiver and successful pairing, the “M LED tight will remain green.

2. Bluetooth mode:
   Turn the keyboard switch to the 87 position, hold the keyboard “FN + Q/W/E keys” for 3 seconds, the keyboard will enter Bluetooth host 1/2/3 pairing mode, the “M™ LEO light will quéckty flash in blue/cyan/purple to indicate that it has entered peiring state. Search for Bluetooth signat: 875.0 KB and BT3.0 keyboerd, when the pairing is successful, the °M” LED light will remain steady blue/cyan/purple.

ΙΙΙ. BACKLIGHT EFFECT/BACKLIGHT COLOR/BACKLIGHT SPEED AND BRIGHTNESS

1. Press FN298 to cycle through the backlight effects and switch between 20 becklight effects.
2. Press FN2e0 to open and close the backlight effect of the front main key area.
3. Press FN29 to adjust backlight color: red, green, blue, yetlow, pink, cyprus, white, RGB.
4. Press FN2+ “Z/X” to adjust backtight flow speed, 5 speeds available. When adjustment is to the limit, the CAPS. key position will flash red Ught 3 times to signal.
5. Press FN2+ “-_/=+” to adjust backlight brightness, 5 levels available. when adjusting to the limit, the CAPS key position vil flash red light 3 times to signal.

IV. LIGHT RECORDING

1. Press FN2¢Backspace to enter the custom lighting mode, by defauit the A/W/S/D ley position ts steady green.
2. In this mode, press FN2«Backspace, the CAPS key position red LED will flash slowly. Continuously press the desired key to select the constant light display cotor, the LED will cycle through: red, green, blue, yetlow, purple, cyprus, white, off.
3. When done, press FN2+Backspace fo save.
   To redefine a key position’s backlight color, repeat the 2 and 3 steps. Press FN2+8 to eat the current custom lighting mode.

V. LOW BATTERY INDICATOR / CHARGING MATTERS

1. Len battery indication: when the keyboard es in 2.4G of 8T working mode, if the built-in battery of the keyboard is tow, the “M” LED light of the keyboard will flash red to remind you to charge tn time.
2. Charging Matters: This keyboard supports charging modes with portable power source / external power adapter / effective US8 port of computer.
   Warning:
   * Please use the external power adapter with output of 5V – 2A or SV – 1A,

• Use a portable power source vath output of SV – 2A oF SV – TA.

VI. AUTOMATIC POWER SAVING MODE

when the keyboard is in the 2.46 or 8T working state and unused for 30 seconds, it will enter a first-tevel power-saving state (the keyboard backlight effect / LED indicator bohr ts aff). Hf unused for 30 minutes, the keyboard will enter a second-level deep power-saving state. Press any key to wake up the keyboard for use in any power-saving state.

VII. RESET TO FACTORY SETTINGS

Press and hold FN2 + CapsLk for 3 seconds to reset to factory settings.

COMBINATION KEYS

PACKAGE CONTENTS

User Manuai1, Certification Card1, Data Cablel, Key-switch Puller1, Keycap Putler1, Additional Switch*2.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF waming for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>