Machenike K500PRO Wired Mechanical Keyboard User Manual

Machenike K500PRO Wired Mechanical Keyboard

OVERVIEW

Technical Specification

Multimedia Functionality

Usage Instructions

1. Wired Connection
   Move the switch to the OFF position, then connect the USB cable to the computer for wired mode.

2. Wireless Connection
   Switch the toggle to the 2.4G position for 2.4G mode. Switch the toggle to the BT position for Bluetooth mode. Use Fn+ 1 /2/3 for Bluetooth pairing and Fn+4 for 2.4G pairing.
   a. Bluetooth Pairing: Pairing name: KS00 Pro-B94W 3.0, KS00 Pro-B94W 5.0.
   Move the switch to the BT position, and hold the FN + “1 !” / “2@” / “3#” keys for 3 seconds to enter the corresponding channels for Bluetooth. the M indicator will flash in blue/cyan/pink indicating the pairing state. When pairing is successful, the indicator light stays on.
   b. 2.4G Mode Pairing:
   Move the switch to the 2.4G position, and hold the FN + “4$” key for 3 seconds to enter the 2.4G pairing mode, the M indicator will flash yellow. Then connect the receiver to the computer. When the pairing is successful, the M indicator will stay yellow.

3. Backlight Effects
   FN + Right SHIFT: Change lighting patterns, and supports 15 different lighting patterns.
   FN + ENTER: Change backlight colors, supports red, green, blue, yellow, pink, cyan, white, and RGB switching.
   FN + “Up” or “Down” Arrow Keys: Adjust backlight brightness, the A indicator blinks 3 times when reaching the maximum level, 5 levels adjustable.
   FN + “Left” or “Right” Arrow Keys: Adjust backlight flow speed, the A indicator blinks 3 times when reaching the maximum level, 5 levels adjustable.

4. Side Light Effects:
   a. Use FN + “+” key to change the patterns of the side light (flow light – neon – constant brightness – breathing – off).
   b. Use the FN + “-” key to adjust speed in flow, neon, and breathing modes (4-level speed).
   c . When in constant or breathing mode, press FN + PrtSc to switch colors (red – green – blue – yellow – purple – cyan – white).

5. System Switch
   The default system mode after power-on is Windows. By pressing FN+A, you can switch to the Mac system mode and the ‘A’ key’s red light will flash three times. By pressing FN+W, you can switch to Win system mode and the ‘W’ key’s red light will flash three times.

6. Light Recording
   Pressing FN + Backspace will initiate the custom lighting mode with the def a ult keys (ESC, A, s, D, W, ↑ ↓ ← → ) being lit. Press FN + Backspace again to start recording. The ‘A’ indicator will keep flashing until the recording is completed. Press the same key until you see the required color, then continue setting other keys. To form the needed backlight pattern, press FN + Backspace once done to save these settings. While playing the light macro, press FN + Backspace and the defined key will light up (FN and NUM keys cannot customize the light).

7. Power-Saving Mode
   The keyboard backlight will enter standby mode and turn off after 3 minutes of inactivity and will enter sleep mode after 30 minutes of inactivity.

8. Charging and Low Voltage
   Connect the Type-C USB cable to either a computer or a charging adapter. The keyboard will be in charging state, the battery indicator will be constantly lit in red during charging and green when fully charged. When the battery voltage is below 3.3V, the light will turn off, and the battery indicator will slowly flash red. When the battery voltage is 3.0V or lower, the keyboard will turn off.

9. Battery Status Display
   Press the FN+ALT keys, the entire backlight will be off. The area [1 !]-[O)] indicates the battery status.
   When the battery is low, keys [1 !]-[3#] will light up in red. For battery level above [3#], [1 !]-[O)] will display in green. It will restore the default light effect after releasing it.

10. Reset Factory
    Pressing FN+ESC for 3 seconds will restore the factory settings and clear all macro settings.

Package List

• Manual*1
• Warranty Card*1
• Certification*1
• Cable*1
• Switch Puller*1
• Key Puller*1
• Extra Switch*2.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

GLOBAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>