SHANTOU B35 Wireless Headphone User Manual

SHANTOU B35 Wireless Headphone

Specifications

• Frequency Response : 20-20KHz
• Max Output Power : 20mW
• Working Range: 8-10m
• Battery voltage: 3.7V
• Battery capacity: 200mAh
• Battery Charging Voltage: DC4.2-5.5V
• Charging Time: about 2 hours
• Working Time : about 12 hours
• Impedance: 32 ohm
• Sensitivity: 110+/-3dB
• Speaker diameter : 40mm

Product Usage Instructions

Power:
To power on, long press the POWER button for more than 3 seconds. The headphones will turn on and enter Wireless Mode with blue and red lights flashing alternately. To power off, long press the POWER button for more than 3 seconds until the LED indicator light turns off.

Button Function:

• POWER: Power on/Power off
• Volume up: Long press to increase volume, short press to move to the next track.
• Volume down: Long press to decrease volume, short press to go to the previous track.

Function Description:

• Power on: Long press POWER for more than 3 seconds to turn on the headphones in Wireless Mode.
• Power off: Long press POWER for more than 3 seconds to turn off the headphones.

Button Guide:

• Hang on: Short press the POWER button when receiving a call.
• Hang up: Short press the POWER button during a call.
• Dial back: Double-click the POWER button.
• Play music: Short press the POWER button to play music on connected devices.

Wireless Mode:

• Pairing: Turn off the Wireless function on connected devices to enter pairing mode. Search for device named B35 to connect without a password.
• Subsequent pairing: After powering on, the headphones will automatically connect to the last paired smart device after 3 seconds.

Specifications

• Frequency Response: 20-20KHz
• Max Output Power: 20mW
• Working Range: 8-1 Om
• Battery voltage: 3. 7V
• Battery capacity: 200mAh
• Battery Charging Voltage: DC4.2-5.5V
• Charging Time: about 2H
• Working Time: about 12H
• Impedance : 32 ohm
• Sensitivity: 110+/-3dB
• Speaker diameter: 40mm

Button Function

1. “POWER ” Power on/Power off
2. ” + ” Volume up: long press Move next: short press
3. ” 一’, Volume down: long press Move previous: short press

Function Description

1. Power on: Long press” POWER” for more than 3 seconds.the headphone tum on and enter Wireless Mode. The blue and red lights” flash alternately.
2. Power off: Long press ” POWER ” for more than 3 seconds,the LED indicator light is off and the headphone turn off

Button Guide

1. Hang on: Short press ” POWER” button when being called
2. Hang up: Short press ” POWER” button when calling
3. Dial back: Double-click” POWER” button.
4. Play music: Normally short press” POWER” button to turn on the smart devices automatically to play music
5. Continue to play music after the call : When there is an incoming call, the music will be automatically suspended. After the call, you need to short press the “POWER” button to continue playing

Wireless mode

• Repairing : turn off the Wireless function of the connected smart devices, at this time.the Wireless headset and the last matching device got disconnected,LED light flashed between red and blue.and enter the Wireless pairing mode.then tum on the Wireless function of the smart devices, search for the device named “B35” to get connected without a password, after pairing successfully , voice prompts “connected”, the blue LED is on and flash slowly after working
• Subsequent pairing: 3 seconds after powering on, it will automatically search and connect the smart device that paired last time Warning voice of maximum volume: “Didi”
• Power saving mode: headset will automatically power off after pairing continuously for 5 minutes; it will cut off power supply automatically after using an Aux-in cable for power-saving

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is   encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

FAQ

• Q: How do I know when the headset is successfully paired?
  A: When successfully paired, the voice prompt will say “connected,” and the blue LED will be on and flash slowly during operation.

• Q: How can I conserve power with the headset?
  A: The headset will automatically power off after being continuously paired for 5 minutes. Additionally, it will cut off power supply automatically when using an Aux-in cable for power saving.

• Q: What is the warning voice of maximum volume?
  A: The warning voice indicates that the headset has reached its maximum volume level.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>